Operator's Manual RRFT. MRN 3/8 in. 14.4 VOLT CORDLESS DRILL-DRIVER RIGHT ANGLE Variable Speed / Reversible Model No. 315.101531 Save this manual for future reference WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman web page: www.sears.
• General Safety Rules ................................................................................................................................................. • Specific Safety Rules ...................................................................................................................................................... 4 • Important Safety Instructions for Charger ....................................................................................................................
,_ WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
SERVICE • Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. • Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator. ADDITIONAL • • Always wear safety glasses with side shields.
chemicals that can damage, weaken, or destroy plastic. WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. • • • Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage. b.
Important:Someofthefollowingsymbolsmaybeusedonthistool.Pleasestudythemandlearntheirmeaning.Proper interpretation ofthesesymbolswillallowyoutooperatethetootbetterandsafer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time "X.
SPECIFICATIONS Chuck ............................................................................................................................................................. Motor .................................................................................................................................................................. 3/8 in., Keyless 14.4 Volt DC Switch .............................................................................................................................
BATTERYPACK SHOWNIN CHARGER KEYLESS CHUCK HARGER DIRECTIONOF ROTATION SELECTOR (FORWARD/ REVERSE/LOCK OFF) REDLED ON INDICATES FASTCHARGINGMODE GREENLED ONAFTER /_--_"_ |_ -_'_-"_---_" FASTCHARGING CYCLE,INDICATES ,NR,OKLE CHARGE =ODE YELLOW AND GREEN SWITCH DISCHARGEDOR DEFECTIVEBATTERY PACK STORAGE WRIST STRAP_ _ SCREWDRIVER _v" I _ _/ _ / 4-1/2in, BATTERY PACKSHOWN IN TOOL Fig. I INSTRUCTIONS PACKING LIST When unpacking the tool: 3/8 in.
_k LED FUNCTIONS OF CHARGER LED WILL BE ON TO INDICATE STATUS CHARGER AND BATTERY PACK: WARNING: Do not allow familiarity with the tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. BATTERY PACK The battery pack for your toot has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until light on front of charger changes from red to green.
SWITCH REVERSIBLE See Figure 2. See Figure 2. To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. This direction of rotation is reversible and is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch for drilling. The drilling direction is reversed when the selector is to the right of the switch.
INSTALLING BITS See Figure 4. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 2. • Open or close the chuck opening is slightly larger use. Also, raise the front bit from falling out of the • Insert the drill bit straight into the chuck the full length of the jaws as shown in figure 4. • Tighten the chuck jaws on the drill bit. jaws to a point where the than the bit size you intend to of the drill slightly to keep the chuck jaws.
TO INSTALL BATTERY PACK • • Lock the switch trigger on the drill by placing the direction of rotation selector in the center position. See Figure 2. • Place the battery pack in the drill. Align the raised rib on the battery pack with the groove inside the drill. See Figure 7. Make sure the latches on each side of the battery pack snap into place and the battery pack is secured in the drill before beginning operation.
DRILLING ,_ See Figure 8. _ WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. WARNING: Be prepared for binding or bit breakthrough. When these situations occur, drill has a tendency to grab and kick opposite to the direction of rotation and could cause loss of control when breaking through material.
CHUCK REMOVAL • See Figures 9, 10, and 11. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 2. • Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely. Insert the hex key in chuck and tighten the chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen the chuck on the spindle.
,_ Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer. All other parts should be replaced at a Sears Service Center. WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Do not abuse power tools. Abusive practices can damage toot as well as workpiece. ,_ _i WARNING: Do not attempt to modify this toot or create accessories not recommended for use with this tool.
-- CRAFTSMAN 14.4 VOLT CORDLESS DRILL-DRIVER MODEL NO. 315.101531 SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 4 3 PARTS LIST Key No. Pad Number Description Qty. 1 6612003 Chuck Screw ...................................................................... 1 2 6903302 Chuck ................................................................................. 1 3 1325101 * Battery Pack (Item No. 9 11044) ........................................
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anytime, ® (1-800-469-4663) day or night (U.S.A. and Canada) www.sears.com www.sears.
