Owner's Manual ICRRFTSMRN ] 3/8 in. Two Speed / Reversible CORDLESS DRILL Model No. 315.111630 Save this manual future reference for _IL CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.
• Warranty ......................................................................................................................................................... 2 • Introduction and Product Specifications ........................................................................................................... • Rules For Safe Operation ............................................................................................................................ 2 3-5 A.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures, SYMBOL A MEANING SAFETY ALERT SYMBOL: Indic_eswarningorcaution.
RULES • • FOR SAFE OPERATION (Continued) NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor couJd ignite flammable liquids, gases, or fumes. DO NOT PLACE BATTERY TOOLS OR THEIR KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products or any strong solvents to clean your tool. DO NOT CHARGE BATTERY TOOL IN A DAMP OR WET LOCATION. BATTERIES NEAR FIRE OR HEAT. They may explode.
RULES • FOR SAFE OPERATION (Continued) An extension cord should not be used unless • Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. • Do not disassemble charger; take it to a qualified serviceman when service or repair is required.
Thefollowingrecommended accessories arecurrentlyavailableat SearsRetailStores. • • 6-Pc.ExtraLengthMagnitePowerBitSet • 30-Pc.PowerScrewdriver/Nutdriver SetandCase • • 17-Pc. Power Screwdriver/Nutdriver A'_kWARNING: KNOW HighSpeedBits(ForWoodor Metal)..3/4 in. Max. KeylessChuck(ItemNo,9-20988) Set and Case The use of attachments or accessories not listed might be hazardous. YOUR DRILL WRIST STRAP See Figure 1. See Figure 1.
,_ ,_ WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. WARNING: Do not allow familiarity with your drill to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. • The battery pack will become slightly warm to the touch while charging. This is non'hal and does not indicate a problem.
Do not hold chuck body with one ,& WARNING: hand and use power of the drill to tighten chuck REVERSIBLE See Figure 3. jaws on drill bits. Chuck body could slip in your hand or your hand could slip and come in contact with rotating drill bit. This could cause an accident resulting in serious personal injury. This tool has the feature of being reversible. The direction of rotation is controlled by a selector located above the switch trigger.
INSTALLING BITS ,_WARNING: Do not insert drill bit into chuck jaws and tighten as shown in Figure 7. This could cause drill bit to be thrown from drill resulting in possible serious personal injury or damage to the chuck, See Figure 6. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 2. • Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
,_ WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Fairure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. DRILLING When drilling metals, use a light oil on the drill bit to keep it from overheating, The oil wirl prolong the life of the bit and increase the drilling action. If the bit jams in workpiece or if the drill stalls, release switch trigger immediately.
CHUCK REMOVAL (continued) ,_ Insert allen wrench in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It can now be unscrewed by hand. See Figure 11. WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Avoid using solvents when cleaning plastic parts.
BATTERIES The battery pack for this dril_ is equipped with 5 nickelcadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this tool have been designed to provide maximum trouble free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn.
CRAFTSMAN I 3/8 in. CORDLESS DRILL - MODEL NO. 315.111630 The model number will be found on a plate attached to the motor housing, Always mention the model number in all correspondence regarding your 3/8 in. CORDLESS DRILL or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING PARTS INSTRUCTIONS LIST Part Number Description 1 616478-003 Screw (Special) ............................................. 1 2 973094-001 Chuck (Item No. _9-20988) ............................. 1 Key No.
In U.S.A.
