Operator's Manual [I:RRFTSMRN°I Belt Sander Double Insulated Model No. 315.117250 Save this manual for future reference. _, WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Visit the Craftsman Web page: www.sears.
• • • • • • • • • • • • • • Warranty.................................................................................................................................................... 2 Introduction ................................................................................................................................................. 2 GeneralSafetyRules...................................................................................................................................
,_ SAVE THESE WORK • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL • Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
SERVICE • • • Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.
Important:Someof thefollowingsymbolsmaybeusedonyourtool.Pleasestudythemandlearntheirmeaning. Properinterpretation ofthesesymbolswillallowyoutooperatethetoolbetterandsafer.
BeltSize......................................................................................................................... 3 in.X 18in.(76cmX 45.7cm) SandingSurface........................................................................................................ 16.5squarein. (106.5squarecm) Input....................................................................................... 120Volts,60Hz,AConly,5.3Amps NoLoadSpeed.........................................................................
INSTRUCTIONS PACKING Your belt sander has been shipped completely assembled. Belt Sander Sanding Belt (3) • Carefully remove the tool and the accessories from the box. Dust Collection Bag • Make sure that all items listed in the packing list are included. • Inspect the tool carefully to be sure no breakage or damage occurred during shipping. • Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool.
Beforeusingthe beltsander,familiarizeyourselfwithall operatingfeaturesandsafetyrequirements. However, donotletfamiliaritywiththetoolmakeyoucareless. TRACKING _IL WARNING:Exercisecautionwhenusingthebelt sander.Carelessactions,forevena fractionofa second,canresultin seriouspersonalinjury. DUST COLLECTION The tracking knob allows you to easily adjust the belt tracking. RELEASE BAG The dust collection bag attaches to the sander and keeps dust to a minimum.
DUST COLLECTION BAG FRONT HANDLE REAR HANDLE TENSION RELEASE LEVER SANDING BELT BLOWEREXHAUST HOLE LOCK-ON BUTTON TRACKING KNOB TRIGGER SWITCH Fig.
• WARNING: Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in dust, shavings, chips, or loose particles being thrown in your eyes resulting in possible serious injury. If the operation is dusty, also wear a face or dust mask. SELECTING Selecting important Aluminum abrasives SANDING Raise the tension release lever. Note: If you are changing sanding belts, remove the old sanding belt at this time.
TOADJUSTSANDINGBELTTRACKING A See Figures 5 and 6. Belt life is greatly increased if you regularly adjust the sanding belt tracking. When correctly adjusted, the outer edge of the sanding belt should be even with the outer edge of the base of the sander. • When you install a new sanding belt, you may need to adjust the sanding belt tracking several times until the belt becomes pliable. in contact with a moving sanding belt could result in serious injury.
USING THE DUST COLLECTION BAG Follow these steps to empty the dust collection bag. • The dust collection bag provides a dust collection system for the sander. ,_ d_j WARNING: Do not use the dust collection bag when sanding metal. Using the dust collection bag when sanding metal creates a fire hazard, which could damage the tool and lead to serious personal injury. TO ATTACH THE DUST COLLECTION See Figure 7.
LOCKINGONTHE SANDER SeeFigure8. Thelock-onfeatureallowsyouto lockthetriggerswitch intheOnposition.Lockingthetriggerswitchonallows youto operatethesanderforextendedperiodsoftime. If youhavethelock-onfeatureengagedduringuseand thesanderis accidentally disconnected fromthepower supply,disengage the lock-onfeatureimmediately. Also,donotlockthetriggerswitchif youmightneedto suddenlystopthe sander. ,_ We designed the sander to provide the proper weight on the sanding belt.
PROPER HAND PLACEMENT See Figure 10. For ease of operation and maintaining proper control, the sander has a front handle and a rear handle. These handles allow two-handed operation, which aids in maintaining control, keeping the sanding area level with the workpiece, and keeping hands clear of the sanding belt. When operating the sander, always hold the front handle with your left hand and the rear handle with your right hand.
,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. ,_ WARNING: The belt sander should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool prevents accidental starting that could cause serious injury.
-- CRAFTSMAN BELT SANDER - MODEL NUMBER 315.117250 -- SEE NOTE 7 2 8 4 Note: The assembly shown represents an important part of the double insulated system. To avoid the possibility of alteration or damage to the system, service should be performed by your nearest Sears repair center. Contact your nearest Sears retail store for service center information.
-- CRAFTSMAN BELT SANDER - MODEL NUMBER 315.117250 -- The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your BELT SANDER or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING B INSTRUCTIONS PARTS LIST Key No. Part No. Description 1 9430401 Logo Label ............................................................................................................ 1 Sanding Belt ......................
