® Save This Manual For Future Reference OW ° MANUAL Model No. 319.226560 Serial No. Model and serial numbers may be found on the nam plate located on the front of the tool. You should record both the model and serial number and retain it in a safe place for future use. LT/ SANDER Caution: • Warranty Read, understand and follow ALL Instructions and rules for safe operation operating before this tool. .
FULL ONE-YEAR WARRANTY ON SEARS BELT and DISC SANDER If this Sears Craftsman Belt and Disc Sander fails due to a defect in material or workmanship within one year' from the date of purchase, RETURN IT TO THE NEAREST SEARS SERVICE CENTER INTHE UNITED STATES, and Sears will repair it, free of charge. If this Belt / Disc Sander is used for cormnercial for ninety days from the date of purchase.
SAFETY 11 ALWAYS INSTRUCTmONS WEAR EYE PROTECTION. Any Sander can throw foreign objects into the eyes which could cause permanent eye damage ALWAYS Wear Safety Goggles (not glasses) that comply with ANSI safety standard Z87o t, Everyday eyeglasses have only impact-resistant lenses.
SAFETY INSTRUCTIONS [] ADDITIONAL SA!FETY DO NOT OPERATE YOUR INSTALLED ACCORDING I .THIS SANDER WOOD ONLY.
SAFETY INSTRUCTHO.NS l_ ADDITIONAL 20USE SAFETY RNSTRUCTIONS PROPER When product using EXTENSION an extension CORD.
SAFETY INSTRUCTIONS m GROUNDING USE ONLY THAT INSTRUCTIONS 3-WIRE THAT HAVE PLUGS AND CONTINUED EXTENSION CONTINUED CORDS 3-PRONG GROUNDING 3-POLE RECEPTACLES ACCEPT THE TOOL'S REPAIR OR REPLACE VVORN CORD DAMAGED IMMEDIATELY...if OR repair or replacement of the electric cord or plug is ever necessary, DO NOT connect the equipment-grounding conductor to a live terminal. PLUG.
TABLE OF CONTENTS SECTION PAGE Warranty. .............................................................. 2 Safety Instructions ............................................... 2 Extension Cord Use ............................................. 5 Specifications ....................................................... 7 UnpacMng and Checking Contents ..................... 8 Know Your Belt/Disc Sander ................................ 9 Assembly. ............................................................
UNPACKING _[ Tools needed for 1, Combination 2_Two hex 3. Slotted AND CHECKING assembly and alignment: CONTENTS (see figure t) Square keys (supplied) and phillips 4_Adjustable screwdriver wrench Fig. I Bi Unpacking (see figure This belt disc/sander from the carton.
KNOW YOUR BELT/DmSC SANDER Dust deflector BACKSTOP belt disc " DISC Sanding ---- Belt bed plate Sanding TABLE --- Sanding BELT TABLE Idler drum --- Disc guard ON/OFF switch with key Base mounting hole Fig. 3 KEY GUIDES FOR PROFESSIONAL DISC TABLE: is used to support sander in vertical position.
ASSEMBLY Ill Installing the sanding 1, Remove the two screws and remove sanding 2_Wipe sanding 3, Peel backing disc (see figure from the sanding disc guard 5) disc guard plate. disc plate clean. from sanding disc, align disc with plate and press saxlding disc firmly on to plate, 4, Reinstall disc guard and tighten screws_ [] Installing the sanding 1 Loosen the bed locking tighten 2, Release 3.
ASSENBL¥ CONTINUED B Hounting the backstop (see figure 9) l Align backstop with hole 2, Install lock washer and flat washer on screw 3 insert screw into backstop hole and tighten, Mounting the belt sander table (see figure 10) 1, Insert washer on belt sander table fastening screv¢. ZAlign holding bracket index and screw hole with indexing and screw hole located on side of the belt bed, 3_Insert screw and tighten. 4_Slide table adjusting bracket Lock and adjust. @ Fig.
OPERATION AND ADJUSTMENTS [] ON t OFF switch (see figure l3) The keyed switch is hutended to prevent unauthorized use of the sander: 1•To mm sander "ON" insert the yellow key into the key slot in the center of the switch Z Push key firmly into the slot, then push switch to the r_,ht to start the sander. 3_ To turn the sander 4. Remove "OFF" push switch to the left., the yellow switch come to a complete key when the sander has stop by gently pulling it forward and out, Fig.
OPEF T ON J AND CONTINUED ADJUSTNENT$ Squaring the tables (see figure 17) lb ensure accurate end sanding the wade tables mt_ be sqtmre to the s_mding snarlhcesprior to using the tables for disc sanding, belt sanding, or vertiml belt sanding I Adjust tame you will be using to be 90" with the sanding sun'ace 2 Using a combination square, place one end on the table with the rifler end against the sanding surface, Check that the table is 90" m the s,mding surface 3 If the table is not 90" to the sanding
BASIC [] Sanding Sanding SANDING inside the inside positioning belt, Hold OPERATIONS curves (see figure 20) curve of' the workpiece is done the workpiece on the idler pulley workpiece firmly with both hands, Edge sanding CONTINUED of long workpieces by of' the sanding (see figure 21 ) Adjust the belt sander table to the desired angle for either straight or bevel sanding of the edge. Hold the workpiece tightly with both hands..
MAINTENANCE FOR YOUR SAFETY, TURN SWITCH "OFF" AND REMOVE THE POWER CORD FROM THE ELECTRICAL OUTLET 3 Adjust the tension ot tlle belt by putting a slotted screwdriver in the bracing sloE. Pushing up on the screwdriver will tighten the tension of the belt between the pulleys. 4 Tighten all 3 screws. 5. Test belt tension by Squeezing both sides of the belt. It"properly adjusted, the belt should "give" about 1/-i inch 6.
PARTS BELT/DISC LIST MODEL SANDER Key Part Number | 2 3 4 5 6 7 8 9 IO 11 12 13 14 15 16 I7 18 19 20 2l 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 3_ 38 39 40 4t 42 43 44 45 46 4" 226560001 226560002 226560003 226560004 226560005 226560006 226560007 226560008 226560009 226560010 226560011 226560012 226560013 226560014 226560015 226560016 226560017 226560018 226560019 226560020 226560021 226560022 226560023 226560024 226560025 226560026 226560027 226560028 226560029 226560030 22656003.
g / 75 73 74 26 67 53 So 34 4g 33 36 _42 43 48 Page I7 39
/I:RRFTSMRN + OWNER'S BE[ r/DISC MANUAL SERVICE MODEL NO. 319.226560 HOW TO ORDER REPAIR PARTS To Call Toll Free For Service: i -800-4-REPAIR ( i -800-473- 7247) For Parts: Now that you have purchased your Belt/Disc Sander, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears stores..