Operator's 5.0 Amp IVlanuan Variable Speed Orbital Sabre Saw Model No. 320.2190 z_ CAUTION Read, understand and follow all Safety Rules and Operaling Instructions in this Manual before using this product Sears Brands Management Corporation Visit our Craftsman webslte: wwwocraflsmanocom .
Warranty .................................................. Page 2 Safety Symbols ............................................... Safety Instructions .......................................... Glossary of Terms ........................................................... Page Pages Pages 3 4-9 9-10 Unpacking ................................. Pages 10-11 Description .................................................... Pages 11-12 Assembly ......................................................
The purpose of safety symbols is to attract your attention lo possible dangers, The salely symbols, and the explanations with them, deserve your careful attention and understanding, Tile symbol warnings DO NOT by themselves eliminate any danger.
1 before using sabre to follow i manual Z_WARNING: BEthis SURE to saw, read Failure and understand result In eleclrlc shock, fire and/or serious personal WORK t AREA all instructions Instrucllons in may all this injury. J | SAFETY Keep your work area clean and well lit, Cluttered workbenches and dark areas invile acctdenls, 2.
TOOL USE AND CARE SAFETY ,_WARNING: BE SURE to read and understand all Instructions before operating this saw. Failure to follow all Instructions listed below may result in electric shock, Ilre and/or serious personal Injury. ALWAYS use clamps or other practical ways to secure and support the workplace to a stable platform,, Holding the work by hand or against your body is unstabts and may lead to loss of control 2 DO NOT force the tool.
ELECTRICAL ] SAFETY conL _WARNING: Doubte insulation precaul[ens when operating this IDol.DOES NOT take the place of normal safety 3,, BEFORE plugging in the tool. BE SURE that the outlet voltage supplied is within Ihe voltage marked on the tool's data plate. DO NOT use "AC only" raled too_s with a DC power supply. 4 AVOID body contact wllh grounded surlaces, such as pipes, radiators, ranges and relrigeralors There is an increased risk of electric shock it your body is grounded 5.
SAFETY SYMBOLS FOR YOUR TOOL s Vo_t ......................................... V The label on your tool may include the following symbols,. A ............................................... Hz ....................................................... W .................................................. mtn ...................... i ............................... Amps Hedz Walls Minuies ............................................... _ __-= .................................................. no .........
SAFETY RULES FOR SABRE SAWS conL 6 MAKE SURE the blade is not contacting the workplace turned on_ before the switch is 7 HOLD TOOL by insulated gripping surfaces (handles) when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make the exposed metal paris ol the tool "live r and shock Ihe operator. 8 SECURE MATERIAL before cutting,. Never hold a workplace in your hand or across your legs,.
ADDITIONAL RULES FOR SAFE OPERATION ,_ WARNING: BESURE follow all Instructions personal Injury_ to read and understand ell instructions. Failure to / listed below may result in electric shock, fire and/or serious J t Know your power tool. Read operator's manual carefully.
Freehand Cul Performing a cut wiflloul using a fence, miter gauge, fixture, work clamp, or other proper device to keep the werkpiece from twisltng or movtng during the cut Orbital Sawing tn addition to the up and down movemenl of a sabre saw's blade, there ts orbtlal action which ihrusts lhe blade forwa_d on the culling stroke and greal]y increases the culling speed over convenllonal sabre saws Scrolling Allows the blade to swivel for tn|ricate pattern cutting Through Sawing Any cutting operation where the
(Fig. 1) 2,,Two wood cutting blades (stored in blade storage compartment) _ 1oSaw 3_Vacuum Adapter (attached Io saw) 4, Carry bag KNOWYOUR SABRE SAW (Fig, 2) NOTE: Before altempttng to use your saw, femlflarlze yourself with all of the operating features and safety requirements, 1 Your sabre saw has a precision buflt electric motor and it should only be connected to a 120-volt. 60-Hz AC ONLY power supply (normal household c_n'ent), DO NOT operate on direct current (DC).
This Sabre Ffg Saw has the following features: conto (Ftgo 2) ! 2 Variable Speed Di,_f On/Off Triggor .,Sw_t_h 8-ll. Power Card .•.,;7__-,_'_ T, RaIlng .... No Losd Speed H ' 5.0 Amps ................................................. B0O - 3000 SPt-,_ (slrokes Input 120-vottm Bevel Cutting Blade Slmke Angle Range 60-Hz c,,i,_ D_'hi_ Weed Culling Deplh in Steel AC ..... 0." !0, 45 _ left and right 11116-Inch "I!4-tn, 12 (6ram) per rain,) ........
BLADE STORAGE (Ftg_ 3 and 4) Your sabre saw comes wtlh 2 wood culling blades that are stored In the blade storage compartment _cated on the very back of the saw under Ihe power cord inlet (see Fig 3),, To open blade sloraga door. remove the vae adapter tube (see Fig.,4) Lift the vac adapter tube up stight]y (io release qab from base plate) and pull vac adapter tube straight out to remove, Pull tab on blade storage door down to open and turn saw upside down lo _.
TOOL-LESS BLADE INSTALLATION cent., 6 Pull down on the blade 1o make sure the blade is securely locked in place NOTE: For use with beth "T' and "U" shanked blades° L_ CAUTION: Once the blade Is tnstslfed in the saw, tt Is always exposed° There is no lower blade guard° Use caution when hsndlfng the saw so that the blade does not catch clothing, skin, etc.
POWER ON-OFFTRIGGER 1 2, 3 4. SWITCH and POWER "LOCK-ON" BUTTON Connecl the plug of your saw to a standard household power outial Start the tool by squeezing the on!elf trigger switch (see Fig t0) To stop the toot.
ORBffAL ACTION (Fig. 12) This saw t_asan orbital control [ever (see Fig. 12) that regu_lates lhe Ihree cuf_ing modes of the saw, Positions "!", _2" and "0". The orbital blade aciion thrusts the blade forward on the cutting stroke (see position t and 2), and greatly increases the curling speed over the norma_ up and down blade action of position 0 POSITION POSITION POSITION Fig.
GENERAL CUTTING TIPS t, Always place _he best or "finished" side of your workplace "face down" So it does not get scraped or abused white sawing ALWAYS CLAMP workplace securely betere sawing, 2 Draw your cutting lines, patterns or designs on the "backside lacing you This moans they would be reversed or backwards from the way they will appear on the '=finished" slde.. 3 Always select the co=.
CUTTtNGWITH A STRAIGHTEDGE (Ftgo14) 1 Mark the pesiIion of the side edge of the saw base and then clamp the straighledge on the mark and paraliet to the cut. 2 As you cut, keep the saw base edge Itush against llle straightedge and ttat on the workptece Z_ WARNING: ALWAYS clamp and support workpiece securely, ALWAYS malnlaln proper control of sew. Failure to clamp and support workplece and lose of contro! of saw could result in serious Injury.
TO ADJUST BASE PLATE FOR BEVEL CUTI'ING (Ffgo 16 and 16a) Z_ WARNING: ALWAYS unplug saw from the making any adJuslmenta or attaching accessories. ' NOTE: ALWAYS remove the blade before adjusting power source BEFORE I the cutting angle., 1 After removing the blade from the saw. remove the vac adapter from under the base (see Sawdust Removal, Page 16).
USING THE EDGE GUIDE (Sold separately) I (Fig, 17 and t7a) _ WARNING: ALWAYS unplug saw from the power source BEFORE making any adjustments or attaching accessories. 1 1 tnsed the bar of the edge guide (sold separately) lhrough the stets in the base of the sabre saw (see Fig, '17).
GENERAL Z_ WARNING: ALWAYS cleaning or performing any _ disconnect maintenance, the tool from the power source BEFORE roleum-based products, penetrating oils, etc, came In contact with plastic ts. Chemicals can weaken plastic, which may result in WARNING: Do damage, NOT at any lime or let destroy brake fluids, gasoline, Ious personal Injury.
5,0AmpORBITAL SABRE SAW MODEL NUMBER 320.2190 The Model Number wilt be found on the Nameplate attached to the handle of the Sabre Saw Always mention the Model Number when ordering parts for this tool,, 5.0 Amp ORBITAL SABRE SAW MODEL NUMBER 320,2190 The Model Number will be found on the Nameplate attached to the handte of Ihe Sabre Saw.
3700214000Washer Pendulum 17 18 2j__ _22 23 _24 25 26 27 __28 29 30 31 32 33 34 _335.o.38 37 .__3._8 .... 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 Plate Needle Bearinq. Needle Pin _ 5700184000 { { 3700147000 3550216000 { i 5660004000 3520126000 Washer C Gear Gear Pin Washer For Shaft Crank Roller 2820854000 Guiding Rod Set .... 3520060000 3520061000 3123014000 3660245000 4870099000 5610024000 3120234000 4540017000 3121733000 3121732000 3700231000 3124601001 561Q021Q,00......
Your Home For troubleshooting, product manuals and expert advice: managemylife wwwmanagarny[tfe,,com For repair - in your home- of all major brand appliances, lawn and garden equipment, or healing and cooling systems, _iii!i:i:i:.i:i! no matter who made it, no matter who sold itl For the replacement parts, accessories and owner's manuals that you need to do-it-yourself For Sears professional installation of home appliances and items like garage door openers and water heaters.
