Operator's Manual CRAFTSMAN’ evolve Hammer Drill Model No. 320.17263 * WARRANTY A WARNING: To reduce the risk of « SAFETY injury, the user must read and * ASSEMBLY understand the Operator's Manual * DESCRIPTION before using this product. *« OPERATION * MAINTENANCE Sears Brands Management Corporation www. craftsman.
JL ee = Warranty Page 2 Safety Symbols Page 3 Safety Instructions Page 4-7 Unpacking Page 8 Description Page 9-10 Operation Page 10-14 Maintenance Page 15 Troubleshooting Page 16 Parts List Page 17-19 Sears Repair Parts Phone Number Back Cover CRAFTSMAN® EVOLVE FULL WARRANTY If this Craftsman® Evolve product fails due to a defect in material or workmanship within one year from the date of purchase, return it to any Sears store or other Craftsman® Evolve outlet in the United States for free replacement.
SAFETY SYMBOL! The purpose of safety symbols is to attract your attention to possible dangers, The safety symbols and the explanations with therm deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
Reyna i Le] AA WARNING: Be sure to read and understand all instructions in this manual before using the hammer drill, Failure to follow all instructions may result in hazardous radiation exposure, electric shock, fire, and/or serious personal injury, A WARNING: Do not attempt to operate this tool until you have thoroughly read al instructions, safety rules, and wakings. Failure to comply with them can result in firs, electric shock, or serious personal injury. Save the manual and refer to it frequently.
extension cords. Recommended sizes of extension cords Volts Total Length of God in feet Ampere Rating 120v | 258 50ft 100% 150ft More Than | Not More Than AWG Not Recommended PERSONAL SAFETY + Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. + Dress properly. Do not wear loose clothing or jewelry.
tool will do the job better and more safely at the rate for which is designed. + Do not use tool if the switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. + Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the fool. Such preventive safety measures reduce the risk of starting the tool accidentally, * Store idle tools cut of reach of children and other untrained persons.
Class Il construction Revolutions or Strokes per minute Indicates danger, warning caution. It means attention! Your safety is involved. SPECIFIC SAFETY RULES FOR HAMMER DRILL » Hold the tool by its insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
UNPACKING A WARNING: Your hammer drill should never be connected to the power source when you are assembling parts, making adjustments, installing or removing bits, cleaning it or when it is not in use, Disconnecting the hammer drill will prevent accidental starting, which could cause serious personal injury. When unpacking the box, do not discard any packing materials until all of the contents are accounted for: 1. Carefully lift the drill out of the carton and place it on a stable, flat surface. 2.
DESCRIPTION KNOW YOUR HAMMER DRILL (Fig. 1} Before attempting to use this hammer drill, familiarize yourself with all its operating features and safety requirements. A WARNING: Do not allow familiarity with your hammer drill to make you careless. Remember that a careless fraction of a second is sufficient to inflict severs injury. Fig.
A WARNING: The safe use of this product requires an understanding of the information on the tool and in this operator's manual, as well as knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules, OPERATION ASSEMBLY AND ADJUSTMENTS {Fig.2) A WARNING: Remove the hammer drill from the carter and examine it carefully. Do not discard the carton or any packaging material until all parts are examined.
turn OFF. LOCK-ON BUTTON (Fig.4) 1. To lock the switch ON for continuous operation, depress the switch and push in the “lock-on” button, then release the switch, 2. Ta stop the hammer drill when in the “lock-on” position, depress and release the switch. Note: if you have the “lock-on” feature engaged during use and your hammer drill becomes disconnected from the power supply, immediately disengage the “lock-on” feature. FORWARD/REVERSE SWITCH (Fig.
or rotation with hammering action. 1. For rotation only, push the switch to the side of the hammer drill with the mark. 2. For rotation with hammering action, push the switch to the side with the mark. DEPTH GAUGE (Fig.6} 1. The adjustable depth gauge is used to control the depth of drilled holes. 2. Install the depth gauge as shown in the Assembly section, 3. Loosen the auxiliary handle to facilitate the adjustment of the depth gauge. 4.
To remove 1. Unplug the hammer drill. 2. Insert the chuck key into a guide hole and turn it counter-clockwise. When footie, remove the bit. 3. Remove the chuck key. HAMMER DRILLING When drilling in concrete, granite, tile, marble, etc. use the hammer action by pressing the button on the marked side. 1. Be sure to use a tungsten carbide-tipped bit. When the hole becomes clogged with chips, do not apply more pressure. Allow the tool to idle and partially remove the bit from the hole. 2.
MASONRY DRILLING {Fig.8) 1. Set the forwardness switch for the desired rotation direction. 2. Secure work piece to keep it from turning when drilling. 3. Push the hammerlock selection switch to set the action mode, 4. Push the switch to start the hammer drill. 5. Apply pressure to the hammer drill handles to keep the bit cutting. 6. Use tungsten carbide-tipped bits for drilling concrete, ceramic tile, brick, etc.
MAINTENANCE A WARNING: To ensure safety and reliability, all repairs should be performed by a qualified service technician at a Sears Service Center, A WARNING: For your safety, always turn off the switch and disconnect the plug from the electrical outlet before performing any maintenance or cleaning. Periodic maintenance of your drill allows for long life and trouble free operation. A cleaning, lubrication, and maintenance schedule should be maintained.
TROUBLE SHOOTING PROBLEM CAUSE SOLUTION The hammer drill does not start when trigger switch Is squeezed Check to be sure power cord is connected to power source and that power source (outlet) is operable Connect to power surge, Confirm power source {outlet is operable Will not drill Check drill bit and chuck jaws Replace drill bit if dull or worn; tighten chuck jaws to firmly secure drill bit Bit cannot be installed Sleeve is not released Release the sleeve Motor overheating Be sure cooling vents are free f
aie n ty Hammer Drill MODEL NUMBER 320.
aie n ty 5620138000 Sower (LH) 3860005000 Chuck S700018000 Ball Bearing Spindle 5660018000 Cir clips For Shaft 3520016000 Gear 3660331000 Spring 3520017000 Impact Gear 3700086000 Seaboard 5700027000 Needle Bearing 3120269000 Knob 3700088000 Reed 3550101000 Lever Pin 3420062000 Bearing Support Ball Bearing 2750131000 Rotor 3700517000 Felt Ring 5610042000 Tapping Screw 3320048000 Right Housing 3420064000 Right Alum Cover Tapping Screw 2240134000 Name Plate 4960005000 Carbon Brush 2800016000 Brush Holder 37004
ie Ge Beh ey 2820725000 1 2820717000 1 30 2820718000 Internal Wire SAYS 1-8 ! 2820719000 1 2820721000 1 2820723000 1 31 3121008000 Cord Guard 1 32 4810002000 Power Cord & Plug 1 33 5610023000 Tapping Screw 2 34 3700285000 Cord Anchorage 1 35 3320048000 Left Housing 1 36 2240139000 Name Plate 1 37 3420063000 Left Alum Cover 1 38 5620037000 Screw 3 39 3120263000 Auxiliary Handle 1 40 3121143000 Handle Hoop 1 41 3550098000 Depth Stop 1 42 5640015000 Hexagon Head Bolt 1 77263 Manual Revised 08-0709 Page 19
at your home or ours Get it fixed Your Home Far expert troubleshooting and home solutions advice: manage [fi home www.managemyhome.com For repair — in your home — of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself For Sears professional installation of home appliances and terns like garage door openers and water heaters.
