Operator's Manual MIXTEC 2.5 AMP MULTI-TOOL KIT Model No. 320.35078 (Uhs [5 + WARRANTY hd + SAFETY + ASSEMBLY A WARNING: To reduce the risk of injury, + OPERATION read and understand the Operator's manual « MAINTENANCE before using this product. » LIFESPAN Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
TABLE OF CONTENTS Warranty page 2 Safely Symbols pages 4-5 Safety Instructions pages 6-8 Description pages 9-10 Assembly pages 10-11 Operation pages 12-25 Maintenance page 26 Troubleshooting page 26 Part List pages 27-29 CRAFTSMAN ONE YEAR LIMITED WARRANTY FOR ONE YEAR from the date of purchase, this product is warranted against any defects in material or workmanship. With proof of purchase, defective product will be replaced free of charge.
A DANGER: People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. A warning: Sore dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.
SAFETY SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers, The safety symbols and the explanations with them deserve your careful attention and understanding.
SAVE THESE INSTRUCTIONS Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to aerate the tool better and more safely.
SAFETY INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS A warning: Read and understand all instructions. Failure to follow all instructions in this Operator's Manual may result in electric shock, fire, and/or serious personal injury. Save all warnings and instructions for future reference. s The term “power tool” in all warnings listed below refers to corded power tools or battery-operated (cordless) power tools. WORK AREA SAFETY + Keep your work area clean and well lit.
PERSONAL SAFETY » Stay alert, watch what you are doing and use common sense when operating a power tole. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power fools may result in serious personal injury. Use personal protective equipment, Always wear eye protection Protective equipment, such as a dust mask, non-skid safety shoes, hard hat, or hearing protection, used for appropriate conditions, will reduce personal injuries.
Keep cutting tools sharp and clean. Properly maintained cutting foals with sharp cutting edges are less likely to bind and are easier to control Use the power tool, accessories, tool bits, ele. in accordance with these instructions, taking info account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
DESCRIPTION KNOW YOUR MULTISTORY (Fig. 1} Fig. 1 i 9 On/Off Switch Live Tool Quick-Release Lever ~~ Indicator Light _ Flange Bolt Variable-Speed Dial PRODUCT SPECIFICATIONS Input 2.5 Amps Rating 120V, 80Hz, AC Oscillation Rate Oscillation Angle +1.4 degrees Tool Weight 3.5 lbs. A WARNING: The safe use of this product requires an understanding of the information on the tool and in this operator's manual as well as knowledge of the project you are attempting.
QUICK-RELEASE LEVER The quick-release lever allows for tool-less exchange of application totals, VARIABLE-SPEED ADJUSTMENT DIAL The variable-speed dial is located on the back of your tool for selecting the appropriate sped. LED WORK LIGHT The LED work light is located in the front of the tool. This feature provides extra light for increased visibility, LIVE TOOL INDICATOR LIGHT The eight shines green when tool is plugged into a power source.
SELECTING THE APPLICATION TOOL APPLICATION TOOL MATERIALS Sanding Plate and Sandpaper Bare or Painted Wood, Plaster, other surfaces, depending on sandpaper grit Circular Saw Blade Wood, Plastic, Drywall, Non Ferrous Metals, Thin Sheet Metal and other materials Carbide Circular Blade Grout, Plaster, Porous Concrete and Masonry Scraper Blade Paint & Varnish, Bonded Carpet, Soft Adhesives, Vinyl Flooring, wood and other Floor Coverings.
lassie ON/OFF SWITCH (Fig. 2) Fig.2 1. Conn act the power cord of your multi-tool to a standard household power outlet. 2. To turn the tool ON, push the on/off switch forward. oe 3. To tum the tool OFF, pull the [— on/off switch backward. VARIABLE-SPEED DIAL (Fig. 3) The variable-speed feature on this multi-tool allows you to match the proper speed to the material being Fig.
LIVE TOOL INDICATOR LIGHT (Fig, 5) Live tool indicator light The live tool indicator light is a green light located on the back of the tool. This light is always on when the multi-tool is plugged into a power source. Lane ule TEs le Bo ATTACHING THE APPLICATION TOOLS (Figs. 6,7, 8,9 and 10) A WARNING: Failure to unplug the tool from the power source when assembling parts, making adjustments, or changing application tools could result in accidental starting and cause serious injury.
Align the grooves on the application tool with the four raised ribs on the drive shaft. Put the application tool onto the drive shaft (Figs. 7 and 8). With your gloved hand holding the application tool, insert and depress the flange bolt until you hear a click indicating that the application tool is secured (Fig. 9). Push the quick-release lever with your palm to lock the driver shaft (Fig. 10). NOTICE: Attach the application tool in the desired orientation for the task at hand.
SANDPAPER KIT DESCRIPTION (Fig. t) » 3 Pisces sandpaper: 3 sate of 60, 120, and 180 grit. Always apply to the compatible sanding plate {supplied with your multi-tonal} The sandpaper Kit is also compatible with the Bosch PMFI180E, GOP 10.8V Lind Craftsman Next Multi-tool. Fig. 11 TO INSTALL THE SANDING PLATE Disconnect the multi-tel from the power source. Push the Buick-re] e lever fully open with your palm to loosen the flange bolt (Fig. 8).
TO INSTALL THE SANDPAPER (Fig, 12a) Ah warning: Check that the sanding plate and sandpaper are correctly attached. An incorrect or insecurely fastened application tool can come loose during operation and cause a hazard. 1. Follow the directions for attaching the application too! to attach the sanding plate to the multi-tool. 2. Align the sandpaper with the sanding plate and use your hand to press it firmly onto the sanding plate. 3.
CIRCULAR SAW BLADE Fig. 14 DESCRIPTION (Fig. 14) + High-speed steel circular cutting blade. = Designed for cutting wood, plastic, drywall, non-ferrous metals, thin sheet metal and other materials. pn = The circular saw blade is also compatible with the Fain Multi-Master tool and Craftsman Next Multi-tool, ann, TO INSTALL THE CIRCULAR SAW BLADE oh CAUTION: Wear protective gloves. Ab erring: Usa sharp, undamaged saw blades only. Deformed or blunt saw blades or saw blades that are otherwise damaged can break.
2. Push the quick-release lever fully open with your palm to loosen the flange bolt (Fig. 16). Overmaster the flange bolt. 3. Ensure that the inner threads and the drive shaft are clean. 4. Align the grooves on the circular cutting blade with the four raised ribs on the drive shaft; put the blade root the drive shaft (Fig. 17). 5. With your gloved hand holding the blade, insert and depress the flange bolt until you hear a click indicating that the blade is secured. 8.
TO INSTALL THE CARBIDE CIRCULAR BLADE A warning: Use sharp, undamaged saw blades only. Deformed, blunt saw blades or saw blades that are otherwise damaged can break A WARNING: When sawing light building materials, observe the precautions and the recommendations of the material suppliers. Ah WARNING: Plunge cuts may only be applied to soft materials, such as wood, gypsum plaster boards, etc. oH CAUTION: Wear protective gloves. 1. Disconnect the multi-tool from the power source. 2.
CUTTING GROUT WITH THE CARBIDE CIRCULAR BLADE (Fig. 21) 1. Connect the multi-tool to a power source 2. Draw the cutting lines on the work piece, if desired. 3. Tum on the tool and allow it to come to the full desired speed. 4. Place the carbide circular blade against the work piece at a 90° angle. 5.
4. Align the grooves on the scraper blade with the four raised ribs on the drive shaft; put the scraper onto the drive shaft Fig. 28). 5. With your gloved hand holding the blade, insert and depress the flange bolt until you hear a click indicating that the scraper blade is secured. 8. Push the quick-release lever with your palm to lock the driver shaft (Fig. 10).
CARBIDE TRIANGULAR RASP [5006 DESCRIPTION (Fig. 26) » Carbide tipped triangular grout rasp. ® Designed for grout, masonry, twinset, wood and removal of hardened adhesives on the wall files s The triangular rasp is also compatible with the Fern Multi Master Tool and Craftsman Dexter Multi-tool. TO INSTALL THE CARBIDE TRIANGULAR BAPS A caution: wear protective gloves 1. Disconnect the multi-too! from the power source. 2. Push the quick-release lever fully open with your palm to loosen the flange bolt (Fig.
USING THE CARBIDE TRIANGULAR RASP (Fig. 29) 1. Connect the multi-tool to a power source. 2. Draw the cutting lines on the work piece. 3. Tum on the tool and allow it to some to the full desired speed. 4. Put the rasp flat against the work piece and apply appropriate pressure. 5. Remove any hardened adhesive or grout on the surface of the wall tiles. FLUSH CUT BLADE DESCRIPTION (Fig. 30) . Bi-metal, straight-edge, flush cut blade. Designed for cutting wood, plastic, drywall, soft metal and other materials.
5. 8. With your gloved hand holding the blade, insert and depress the flange bolt until you hear a click indicating that the flush-cut blade is secured. Push the quick-release lever with your palm to lock the driver shaft (Fig. 10}. A warning: Do not attach the flush cut blade, facing backwards, as operation in this position may cause serious injury.
ACCESSORIES NOTICE: The multi-tool can be used with the Craftsman accessories below {sold separately): MODEL DESCRIPTION 67650 Carbide Circular Blade 67651 Circular Saw Blade 67652 Scraper Blade 67653 Flush Cut Saw Blade 87654 Carbide Triangular Rasp £7655 Sandpaper Kit 60, 120, 180 grit 17374 Sandpaper Kit {220, 280, 320 grit) 17375 Detail Saw Blade 17376 Rough Cut Saw Blade 30858 Caulk Removal blade 30753 Sanding Pad 3102 Felt Polishing Pad 31022 Detail Sanding Blade 31023 Detail Sandpaper 2549 Detail Str
MAINTENANCE A warning: Avoid using solvents when cleaning plastic parts, Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use, Use clean cloths to remove dirt, dust, oll, grease, eto, A warning: Do not at any time allow brake fluids, gasoline, petroleum based products, penetrating oils, etc. to come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
abnegate 2.5A VARIABLE-SPEED MULTI-TOOL MODEL NUMBER 320.35078 The Model Number will be found on the Nameplate. Always mention the Mode] Number when ordering parts for this tool, To order parts, call 1-800-469-4863. 5078 Dissemblance 12.
PART LIST 2.5A VARIABLE-SPEED MULTI-TOOL MODEL NUMBER 320.35078 The Model Number will be found on the Nameplate. Always mention the Mode] Number when ordering parts for this tool, To order parts, call 1-800-469-4863.
hi HL Lan ne 25 3321487000 Right Housing 1 28 5610024000 Tapping Screw 2 27 3120234000 Cord Anchorage 1 28 Right Indicator Caver 1 28 3126796000 Switch Actuator 1 30 3551798000 Bush 2 31 3402898000 Lever 1 32 5670317000 Pin 1 33 2800176000 Brush Holder 2 34 4960273000 Carbon Brush 2 35 4930036000 Receptacle 2 36 3126787000 LED Cover 1 37 Oil Impregnating Bearing 1 38 Quick Clamp Assembly 1 39 Lock Pole 1 40 3520628000 Lever 1 41 3550031000 Washer 2 301 3810537000 Wood & Metal Plunge Cut Blade 1 302 Scraper
