Operating instructions

KightF_x 811512003 1 :18 PAGE 8111 RightFax
SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION
Trigger cap leaks air 1. O-ring damaged 1. Check and replace damaged O-ring (Fig. 9, No. 55)
2. Valve stern, seal or O-rings damaged 2. Check and replace damaged stern, se_l or O-rings
(Fig. 9, Nos. 55, 56, 57 and 60)
Cap leaks air 1. Cap bolts toose 1. Tighten bolts (Fig 9, No. 1)
2. Damaged gasket 2. Check and replace damaged gasket (Fig. 9, No. 3)
Nose leaks air 1. Damaged cylinder O-ring 1. Check and replace damaged O-ring (Fig. 9, No. 12)
2. Damaged bumper 2. Check and replace damaged bumper {Fig. 9, No. 14)
3. Ram guide damaged 3. Check and replace guide (Fig. 9, No. 15)
Tool will not operate 1. Insufficient air supply 1. Check air supply
2. Damaged or worn heed valve O-dng 2. Replace damaged or worn O-ring or seal
or seal (Fig, 9, Nos. 5 and 9)
3. Damaged head valve spring 3. Replace damaged spring (Fig. B, No. 6)
4. Head valve binding in cap 4. Clean and grease cap and head valve
(Fig, 9, Nos. 2 and 9)
Tool operates slowly
or loses power
I
Tool skips fasteners or
nconsistsnt operation
1. Damaged head valve spring
Z Damaged or worn O_ngs
3. Damaged trigger assembly
4. Build-up on ram
5. Cylinder not sealed on bumper
propedy
6. Insufficient air supply
7. Head valve poorly lubricated
1. Worn ordamaged bumper
2. Build-upon ram or nose
3. Insufficient air supply 3.
4. Damaged or warn piston O-ring 4.
5. Damaged magazine springs 5.
6, Magazine-nose bolts loose 6.
7. Fasteners too short
8. Damaged fasteners
9. Inconect fastener size
10. Cap leaks
11. Damaged trigger valve seal and
O-rings
12. Bent or damaged ram
13. Dirty magazine
14. Damaged orwom magaslne
1. Check and replace damaged swing (Fig 9, No 6)
2. Check and replace damaged or worn O-dr_ja
3. Check and replace trigger assembly
4. Clean piston/ram assembly (Fig. 9, No. 11)
5. Disassemble cylinder and assemble properly
6. Check air supply
7. Disassemble heed valve (Fig. 9, No. 9),
dean, grease, and assemble properly
1. Check and replaCe bumper (Fig, 9, No. 14)
2. Clean and grease piston/ram assembly (Fig. 9, No. 111
and inside of nose cover (Fig. 9, No. 21)
Check air supply
Check and ragl_ca O-ring (Fig. 9, No. 10)
Chedx and replica springs (Fig. 9, No, 34]
PJlgn nose wffh magazine and tighten bolts
(Fig. 9, No. 24)
7. Use Sears recommended fasteners only
8. Discard damaged fasteners
9. Use Sears recommended fasteners only
10. Tighten cap bolts [Fig. 9, No. 1). Check and replace
damaged gasket [Fig. 9, NO. 3)
11. Check and replace damaged seal and O-rings
(Fig. 9, Nos. 55, 57 and 60)
12. Check and replace damaged piston/ram assembly
(Fig. 9, No. 11)
13. Clean magazine and lubricate with a
dry, film lubricant.
14. Check and replace magaslne (Fig, 9, No. 37)