CRRFTSMRN Operator's Manualo 6 x 48" Oscillating Belt 12" Disc SANDER Model No. 351.226061 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 17985.
Warranty ....................................... • Proper electrical receptacle should be available for tool. Three prong plug should be plugged directly into properly grounded, three-prong receptacle. 2 Safety Rules .................................... Unpacking ..................................... Assembly ..................................... Installation .................................... 2 3 3-4 4-5 Operation .................................... Maintenance ....................................
ATTACH FOOT RESTS Refer to Figure 12. Required parts and hardware: • Four foot rests with bolts • Eight 5/1o" flat washers • Four s/_+"-18Hex nuts Refer to Figure 1. Check for shipping damage. If damage has occurred, a claim must be filled with carrier. Check for completeness. Immediately report missing parts to dealer. CAUTION: Sander with cabinet weighs approximately200 Ibs. At least two people are required to attach foot rests. The sander comes assembled as one unit.
• Loosen and remove hex head bolt and flat washer from the disc table. NOTE: Though the motor works at 115/230-volt AC, sander must be operated at 115 volts only. • Replace hex head bolt with the handle provided. Secure disc table to disc guard using the handle and flat washer. Horsepower (Maximum Developed) ................... ATTACH ABRASIVE DISCTO ALUMINUM DISC Refer to Figures 3, 4 and 11. • Sander is shipped with the abrasive (Key No. 5) not applied to the aluminum disc (Key No. 1). Amperes ..
• Green (orgreenandyellow) conductor incordisthe grounding wire.If repair orreplacement oftheelectric cord orplugisnecessary, donotconnect thegreen(orgreen andyellow) wiretoa liveterminal. Motor and wires are installed as shown in wiring diagram (See Figure 7). Motor is assembled with approved, 3-conductor cord to be used at 115/230 volts. Motor is prewired at the factory for 115 volts.
The two dust collection chutes accept the standard 4" dust collection hose for quick removal of dust. The adjustable miter gauge can be used on both the belt and disc tables for guiding the workpiece at a desired angle while sanding. • Replace abrasives when they become loaded (glazed) or frayed. SPECIFICATIONS • Never attempt wet sanding. If the workpiece becomes too hot to handle, cool it in water. Belt size ............................ Belt platen area ..........................
HORIZONTAL BELT SANDING BELT TRACKING Refer to Figures 9 and 11. Refer to Figures 10 and 11. • Adjust the belt housing to full horizontal position as described in the above section, "Adjusting Belt Housing". Belt (Key No. 25) should oscillate around center on drive and idler drums (Key Nos. 36 and 65). The sander is shipped with the tracking mechanism properly adjusted. However, if adjustment is necessary: • Remove the belt table by removing handle (Key No. 16).
• Use the scale on disc table trunnions to set table at the desired angle. • Loosen and remove knob (Figure 12, Key No. 7) from cabinet door assembly (Figure 12, Key No. 8). • Secure disc table position by tightening the two handles. • Open cabinet door. ABRASIVE • Turn knob (Figure 12, Key No. 7) on bracket (Figure 12, Key No. 17) to release tension on V-belt (Figure 1f, Key No. 6). DISC FINISHING • Abrasive disc sanding is well suited for finishing small flat surfaces and convex edges.
SYMPTOM POSSIBLE Motor will not start 1, Low voltage 2. Open circuit in motor or loose connections 3. Thermal overload protector activated 1. Check power line for proper voltage 2. inspect all lead connections on motor for loose or open connection 2, Push thermal overload button to reset Motor will not start; fuses blown or circuit breakers are tripped 1, Short cimuit in line cord or plug 1. Inspect line cord or plug for damaged insulation and shorted wires 2.
Model 351.226061 Figure 11 - Replacement Parts Illustration / for Sander 25 37 59 39 \ 40 2_ 26 t 52 5O 44 23 44 50 10\ 16.,-_ \ 15 \ 3 j9 23 10
KEY NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 3O 31 32 33 34 35 36 37 38 39 4O 41 42 43 44 45 46 47 48 02225.00 STD503103 02226.01 03333.00 02227.00 STD304340 02228.00 STD502503 08257.00 07296.00 03040.01 01201.00 STD551031 STD651131 04020.00 03041.00 00558.00 03042.00 03043.00 03044.00 03045.00 STD5511t0 03046.00 03047.00 9-28015 04867.00 03049.00 03074.00 03050.01 04020.00 03051.01 STD582066 03053.00 03054.00 STD315535 03056.00 06741.
Model 351.
KEY NO. PART NO. DESCRIPTION 1 3076.01 Cabinet 1 2 STD541031 8 3 STD551031 "A6"-18 Hex Nut* 5A_"Fiat Washer* 4 8879.00 Foot Rest 5 STD523110 1413.00 5/,,-18 x 1" Hex Head Bolt* 4 8 Strain Relief 3 3314.00 Knob 4 Cabinet Door Assembly 9 3077.01 STD541431 1 4 10 STD541010 11 STD551210 3079.00 #10 Serrated Washer* 1 Motor Plate 1 13 14 3080.01 Motor with Cord 1 3081.00 1 15 STD502503 Motor Pulley 1_-20 X 3/. Set Screw* 16 0975.
In U.S.A. or Canada for in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME °"(1-800-469-4683) Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811 Au Canada pour tout le service - 1-877-LE-FOYER s"(1-877-533-8937) For the repair or replacement parts you need: Call 6 a.m. - 1 1 p.m. CST, 7 days a week PartsDirect" 1-800-366-PART (1-800-366-7278) www.sears.