SAVE THIS MANUAL FOR FUTURE REFERENCE OWNER'S MANUAL MODEL NO. 351.226711 .A/P /CRR FTSMRN l"x 6" BELT & DISC SANDER CAUTION: READ ALL INSTRUCTIONS CAREFULLY! • • • • Sold by SEARS, ROEBUCK Part NO. 3899.00 safety Instructions assembly operating instructions replacement parts AND CO., Chicago, IL 60684 U.S.A.
FULL ONE YEAR WARRANTY ON SEARS/CRAFTSMAN 1" x 6" BELT & 015C SANDER If Within one full year tom the date of purchase, this Sset_ Cmfleman 1" x 6" Belt & Dlso Sender fells due to e defect in material or wodunanchlp, Seam will repair It, free of r,hafge, WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES. This warranty glvm; you specific legal rights, and you my have other rigMs which vary from elate to stats. BEARS, ROEBUCK AND CO.
CONTENTS Wmmmty ................................ Goal 8eloty Immmotkme for Power Tcolo ...................... Salety InIWmotlene for Bolt & Disc Sender ................. Motor Speclfk:atlone end Ei$Ctlrlsal Requirements ............ Eieotrk:al ConnecUone .................. a Unpaeldng end Checking Contents ........... TOOLSNeeded ............................ 8 $ 2 As_mb_ ............................... s Operetlon ............................... Malntermr_e ..........................
MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS PROPERLY GROUNDED MOTOR The belt and disc lander Is mmembled with motor 8nd wiringreadied ,., an _eTal i_t of the tool The 120 Volt AC permanent epla €_q_c_ motor has the renewingqx_ncatk_: M_ Devek¢_ Horsepower ................ 1/t Voltage .................................. Amperes .................... 120 3 ............... Phase ................................ RPM ................................... Rotation (viewed from left side) .........
ELECTRICAL CONNECTIONS WARNING: MAKE 8URE THE UNIT 18 OFF AND DISCONNECTED FROM THE POWER 8OURCE BEFORE IN8PECTING ANY WIRING. •r_ motor wxl wlrl_ m k_mlled u _ _ U_ wr_ dk_ram(m F_re 1). The motor Is auen_ed with an apflrowd thnm oo_ ductor €old to be used on 120 volts u Indk:ated. The power su_ to the motor Is con(rolled by a double pole lockingrocker swltc_ Remove the key to prevent unauthorized use. The power flmm are Inse_ed dlmc_ly Into the swltch.
ASSEMBLY CAUTION: Lift the disc table so both tn.lnnions are shoulderod agelnst the guide pips and tighten the knobs. Position dtsc table so the edge of disc table end abrasive disc are parallel and the gap between them Is 1/16'. DO NOT A'rFEMPT ASSEMBLY IF PARTS ARE MISSING. USE OWNER'S MANUAL TO ORDER REPLACEMENT PARTS. FASTEN THE DISC TABLE BRACKET Refer to Figure S. The table support breckt Tlghten the hex bolts seoure_y. (Key No, 15) Is _lached to theleft hand endshleld(Key No.
OPERATING INSTRUCTIONS (Continued) TENSIONING ABRASIVE BELT ADJUSTING BELT TABLE ANGLE Tension ks created by a spring loaded Cam shaft (Key TO adjust the angle of the belt tal_e, loosen the socket head bolt (Key NO` S2) and adJuetto d'm desired angle. Uee a combination square to set the belt table at 45" or i_"_ the abm_ve be_ No.32). Tho tracking whoel IS mounted tho shall on tim oppose side of The spring tenskm Is tmnsml_ed to tho trecldng wheal (Key NO_31) end maintains the ter.don on ben.
OPERATING INSTRUCTIONS (Contlnued) _0o, abrasiveused can be changedtOa dlffarentgrit ro_acgnothe aJum_num €.8C. Addltlonslaluminumdlace are avsHable,Use I separate elumlnumdlsofor _ch gritslze used. Interal_nge the ilun_num dlscto el_nge _ size. Refll_e dlse table. ADJUSTING DISC TABLE ANGLE dll_ tal_e 18IKllUllllll01o from 45" to gO* for beveled work. To adjust the dlso table, Iooeen the two knobe and adJuu to the dselmd angle. When dleo table Is IR dulmd m_ie, lock II Into p(JUon bym_.
MAINTENANCE LUBRICATION The shielded _ manomly IUl_ted further lubrlcelk)n, (Continued) Replace any damaged or mlsldng parts. Use the perte I_ to order parts. besdng_l In this sander are perlit the factory. They require no Any _lempt to repalr the motor may create e heze_ unless rel_r Is done by s qualified service technlclarL Repair service is available at your nearut Seers store.
42 65 50 4 I 3 62 S4 F_re S - F_:i_TW_ pam m_
REPLACEI NT KEY NO. 1 2 I I PART NO. DESCRIP'flON 3896.00 3897.00 Ro(o¢ Stzd_ 3896.00 38ge.00 3304.0O 330S.0O 3306.00 1603.00 3307.00 3308.00 330O.0O 3310.00 3311.0O 5 6 7 8 9 10 11 12 13 14 15 16 T7 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Rutdxrfoot Disc _ _lt_ KEY NO, PART NO. 1 1 2 1 1 37 38 30 40 41 1 44 STD51100_ * dP10-24xS/16' Screw, pan head 6 4! _ STD5.0O_ _lO-_xlrZ'Scrow,pa.hoad STD5231_ : 5/16-18 x 1/2" Boltr hex 27 3329.00 333O.OO Z924.0O 1304.