Manual

RefertoFigures1-9.
CAUTION:Donotattemptassemblyifpartsaremissing.
Usethismanualtoorderreplacementparts.
• Removeallcomponentsfromtheshippingcartonandverify
againstthepartslistabove.Cleaneachcomponentand
removeshippingpreservatives(coatings)asrequired.
NOTE: Before assembling copy crafter, make sure that lathe
is secured to a suitable workbench or stand.
ATTACH TOOL REST BASE {MODEL 24951)
Refer to Figure 2.
• Loosentool restbase lockingbar and slidetool rest base
(suppliedwith the lathe)to as nearthe headstockas possible,
• Loosen locking handle of lathetoolrest and remove toolrest
(suppliedwithlathe).
• Loosentailstookhandleand remove tailstookfromlathebed.
• Insertguide between bed ways.Slide carnagesupport
through slotof guideand secure with set screw.
• Loosen hex nut from the bottom of tool rest base assembly
suppliedwith copycrafter so that the clamping plate can
slide between bed ways, Attach locking handle to tool rest
base.
• Slide tool rest base onto lathe bed, Positiontool rest bases
approximately 30" apart, Tool rest base will later be adjust-
ed closer or further apart, depending upon the length of
the workpieca.
• Replace tsilstock onto lathebed and secureitby tightening
lockinghandle.
_/TOOl Rest
_Carriage Screw
J Guide
:" Tailstock
/J _to_H_a
Ta ndle
Lockin,
Bar
Tool Rest
LockingHandle
Figure 2 - AttachTool Rest Baseto Lathe Bed(Model24951)
ATTACH TOOL REST BASE (MODEL 24952)
Refer to Figure 3.
Loosentailstocklockinghandleand slide ittowardthe rear of
the lathebed tube.
Loosentool restlockinghandleand slidetool rest base
assembly(suppliedwith the lathe)to as near the headstock
as possible.
Loosenthe lockinghandle ofthetool rest holder and remove
toolrest (suppliedwith lathe).
Place tool rest support and bracket onto lathe bed tube
and assemble together using two 8 x 25mm socket head
bolts and two 8ram lockwashers.
Position tool rest bracket and support assembly approxi-
mately 30" from the tool rest base suppliedwith lathe. Tool
rest bases will later be adjusted closer or further apart,
depending upon the lengthof the workpiece.
Insertbrasspin intothreaded hole at toolrest supportand
then thread locking handleinto the support.
Placetool rest holderontotoolrest supportand securein
positionusingone 8 x 30ram sockethead boltand spacer.
Thread lockinghandle intotool rest holder.
Socket H::dac::J_.
Tool Rest Holder _
Head Bolt
_'_ Looking
t, Handle
\Pin
ToolRest Bracket
Loc_kWasher
Figure 3 - AttachTool RestBaseto Lathe Bed(Model24952)
INSTALL SUPPORT BARS IN CARRIAGE ASSEMBLY
Refer to Figure 4,
• Remove gear assembly from carriage assembly by
removingthree sockethead bolts.
• Slide supportbars intocarriage assembly.
• Replace gear assembly into the carriage and securein
positionwith socket head bolts,
_L.f Gear Assembly
'_'_Socket Heed Belt
sT.
Assembly
Support Bar
with Rack
Figure 4 - Install Support Bars
Bar
4
INSTALL COPY CRAFTER ONTO LATHE
Refer to Figure 5,
• Slide bracketsonto support bars,
• Place spacers over bottomof bracketsand then insert
bracketsinto tool rest bases,
• Secure bracketsto supportsbarswith 8 x 40ram socket
head bolts,
BsmpCkce_r_!_ d Bolt
Figure 5 - Install CopyCrafterto Lathe