Instruction Manual JCRRFT$1VlRN°I 12 AMP Motor 220 MPH/360 CFM ELECTRIC Model BLOWERNACUUM No. 358.748240 • Safety • Assembly • • Operation Maintenance • Espar_ol FOR HOUSEHOLD USE ONLY WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product. For answers Mon.-Sat., to your questions about this 7am-Tpm, or 10am-Tpm, Sun.product, • 1-800-235-5878 Sears, Roebuck 530165832-01 and Co.
Warranty Statement Safety Rules Assembly Operation Maintenance Service & Adjustments 2 Parts Available 2 Storage 5 8 9 10 Troubleshooting Spanish Parts Ordering 10 11 Table 11 12 Back Cover FULL TWO YEAR WARRANTY ON SEARS CRAFTSMAN ELECTRIC BLOWER If this Craftsman Electric Blower fails to perform properly due to a defect in material or workmanship within (2) two years from the date of purchase, Sears will replace it free of charge.
ELECTRICAL SAFETY AWARNING: Avoid a dangerous environment. To reduce the risk of electrical shock, do not use in rain, in damp or wet locations, or around swimming pools, hot tubs, etc. Do not expose to snow, rain, or water to avoid the possibility of electrical shock. Do not use on wet surfaces. Do not handle extension cord plug or unit with wet hands. Avoid dangerous situations. Do not use in the presence of flammable liquids or gases to avoid creating a fire or explosion and/or causing damage to unit.
insulation construction consists oftwo • Have all maintenance other than the separate "layers" ofelectrical insularecommended procedures described tioninstead ofgrounding. in the instruction manual performed by your Sears Service Center. Tools andappliances builtwitha • Always see your Sears Service Center double insulation system arenotintended tobegrounded. Nogrounding to replace a damaged impeller.
• Never useforspreading chemicals, fertilizers, oranyother substances which maycontain toxicmaterials. VACUUM SAFETY • Stop the motor and disconnect the power source before opening the air inlet door or attempting to insert or remove the vacuum tubes. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades.
2. Push theblower tubeontothe blower outlet untilitsnaps into place (tube issecured byredtube release button). 3. Toremove theblower tube, press the tuberelease button while pulling on tube. Vacuum } Inlet Restdctor Attaching the vacuum tubes There are 2 vacuum tubes, an upper tube and a lower tube. The upper tube has a vacuum assist handle attached to one end and is cut straight on both ends. The upper tube attaches to the blower unit.
Elbow Tube Zipper Opening HOW TO CONVERT UNIT FROM Tube Release VACUUM USE TO BLOWER USE Button 1. Stop unit and unplug the extension cord. Hole 2. Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area on the vacuum assist handle. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacuum assist handle with your other hand. _1 Opening 3. Close the zipper on the bag. Make sure the zipper is closed completely. 4.
MINIMUM WIRE GAUGE RECOMMENDATIONS Cord Recessed 100 FT. A.IW4G.* *American Wire Receptacl_ Gauge Secure the extension cord to the unit by threading the cord through the cord retainer (see illustration). Insert the cord receptacle into the recessed plug. CAUTION: Failure to use cord retainer could result in damage to the unit, extension cord, or both. °°tlin KNOW YOUR ELECTRIC BLOWER READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
z_ 4rLWARNING: Direct air flow by directing the blower tube down or to one side. Always work away from solid objects such as walks, large stones, vehicles, and fences. Clean corners by starting in corners and moving outward. This will help prevent an accumulation of debris which could fly into your face. Be careful when working near plants. The force of the air could damage tender plants. USING YOUR UNIT AS A VACUUM You MUST make sure the tubes are secure before using the unit.
GENERAL RECOMMENDATIONS AFTEREACH USE Thewarranty onthisunitdoes notcover INSPECT AND CLEAN UNIT & LABELS items thathave been subjected tooper- Stop unit and unplug extension cord. atorabuse ornegligence. Toreceive full each use, inspect complete unit value fromthewarranty, theoperator • After for loose or damaged parts. Clean must maintain unitasinstructed inthis the unit using a damp cloth. manual. Various adjustments willneed • Wipe off unit with a clean dry cloth.
• Clean the entire unit before lengthy storage. • Open inlet cover and clean any dirt, grass, or debris that has collected. Inspect the blower and all tubes. Close and make sure the cover is latched. • Clean air vents and air inlet of debris. • Store your unit and extension cord in a well ventilated area and covered, if possible, to prevent dust and dirt accumulation. Do not cover with plastic. Plastic cannot breathe and may cause condensation and eventual rust or corrosion.