Operator`s manual

2; tztst_lling Line On Spool
Use .06s" _4_zmeter line only.
• To replace the trimmer line on an ezistfug
spool, do the following:
a. Follow "InstatRu_ Spool w/Line," steps"a.-c., _
and remove any _me remaJni_ugon thespool.
Do not wrap more than 40 feet of.065" di*
ameter line ontothe spool.
b. Hold spoolasshown inFigure15.
c. InsertI116 to I/8 inchof line through theholein
theinnerrimofthespool.Figure15. Allowno
more t_m.ui/8inchoflinetoextendbeyondthe
innerrimofthespooltoavoidinterferencewith
thedrivegear.
d. Wrap lineevenlyand firmlyinthedirectionin-
dicatedby thearrowon thespool.Figure 15.
To ensure proper line advance, avoid crossover
orcrisscrossingtheline.
II l . Jml IIIIIIII II
GENERAL MAENTENANCE
undera loadordoes
not turnwhen
switch is pressed.
Line does not ad-
vance orbreaks
while cutting. €:
d.
e.
Line welds a.
ontospool, b.
e.
d.
a.
e. Followinstructionsin _InstailingSpool w/
Line, _steps "f.-j."
• If'the trimmer llne break.soft or backs uv in
the trimmer head, followInstallingSpoolw/
Line/steps"a.-c." Pull slackin theline untilitis
tightly wound on the spool, tea_ng 4-6 inches of
]_e extended.-Continuewith InstallingSp0olwi
_.. Line,"s_ps "f.-j."
xrow of Line
,,,, ,
Figure 15
i r , i i H HI . ,
' ' ' ' 1,,","" ............... ., .........
A. MAINTENANCE SAFETY
* t * •
1. Mam la m the tool according to reeom-
men_dp_'_ed_es. K£-epthe cut_Angiineat the
_ropertength.
2. Disconnect power source before performang
m_Lintenanee. 7.
3. K_ep the unit clean. Use a spongedampened
with a sOlUtionofmildsoapand water.Do notuse 8.
s_qlvents or petroleum bassi cleaner of may kind.
4. Keep air vente free ot debris at all times.
B. TROUBLE SHOOTING CHART
SYMPTOM .......CAUSE .................... ........................
Trimmer Head stops a. Crowding trimmerlineagainst
materialbeingcut.
Line releases
continu0tLsly.
Line usage is
excessive.
5. ReFlace L_mmer head parts that are cracked,
chipped, broken, or damaged in any other way be-
ford using the tool.
6. Use only .065"diameter llne.Neverusewire,
rope,string,,etc.
Use only genuine SEARS replacement parts
ai recommended.
Ixmpect the entire tool Replace damaged psxts.
Checkforfuelleaksand make sureall fastenersare
inplaceand securelyfastened.
Line pullsback
into head.
b. Electricalfailure.
c. None 0£the above.
...,, .,
a. Line improperly routed in head.
b, Line improperlywound ontospool.
Line _size incorrect.
Too little line outside he_&
DL_ a,_umulated on coven
Line size incorrect.
Incorr_ spool.,
Crowdi_ line ags_st material being cuL
Cuttinf at higherspeed _,,necessmT.
Line improperly routed in hea_
b. Line size incorrect.
,JLHm,,,, , ,,,,,,,
a. [£u improperly muted in head.
b. Line size inco_
c. Cuttinff at high speed around hard objects.
d. ,,Crowding RUeS_ainst material bein_._t.....
a, Too little Rue outside of head.
b. Linesize incorro_
""I'H{H IIIHHHHHHHH I IIIHH
ACCESSORIES
SAFETY GOGGLES .................
SPOOL W/LINE 06_" DIA.
EXTENSION CORD (100 R.) ..........
BULK LINE --_t00 F_ .............
--200 FT..............
• --400 F_... • ........
'0P RATOR'SMANUAL ..........,..
REMEDY ..........................
a. Back trimmer bead away fromgrassbeing
cut;allowtipof lineto.do thecutting.
b. Contactyour SEARS ServiceCenter/Depc.
_.€"Contact _our S_RS ServiceCenter/Dept.
8- Remove cove_ Check linerouting.
b.r md eve.ly.
c. Use only.06_ dlameterllne,
& Remove cover. Pu]t4" of line to outside.
e. CI_ coyer.
a. Use only .065" diameter llne.
b. Use proper spool.
e. Cut with tip of line.
d. Reducecuttingspeed.
a. Remove cover.Check linerouting.
b. Use only ,,06_" _eter line. ......
a. Remove cover. Check [ine routing.
b. Use only.06_" diameter line.
c. Reducespeedaround hard objects.
d: cut o,, tine.
a. Remove cover.Pull4" oflinetooutside.TM
b. Use only .065"diameterline.
III Hill IIII{ HI I l, lii ..............
....................... STOC NO. .........
.............................................71-85707
.............................................. 71-85830
............................................. 71-;57020
,,,_.........................................71-85772
........ , .................................... 7Z-85607
. .............. : ....................... . ..... 71_769
................ _ ............................ _30-068416
" , • .