Operator’s Manual 21” LAWN MOWER Model No. 247.379550 CAUTION: Before using this product, read this manual and follow all safety rules and operating instructions. • • • • • • SAFETY UNPACKING P. 8 ASSEMBLY OPERATION MAINTENANCE ESPAÑOL Sears Brands Management Corporation, Hoffman Estates, IL 60179, U.S.A. Used under license Visit our website: www.craftsman.com Form No.
TABLE OF CONTENTS Warranty Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2 Service and Maintenance. . . . . . . . . . . . . . . . . . . . Pages 14-16 Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . Pages 3-6 Off-Season Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 17 Slope Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY INSTRUCTIONS WARNING DANGER This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol, HEED ITS WARNING! This machine was built to be operated according to the safe operation practices in this manual.
SAFETY INSTRUCTIONS • If the equipment should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. • Shut the engine off and wait until the blade comes to a complete stop before removing the grass Bagger or unclogging the chute. The cutting blade continues to rotate for a few seconds after the blade control is released. Never place any part of the body in the blade area until you are sure the blade has stopped rotating.
SAFETY INSTRUCTIONS • Never store the machine or fuel container near an open flame, spark or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances. • To reduce fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel-soaked debris. • Allow machine to cool at least 5 minutes before storing. • General Service: • Never run an engine indoors or in a poorly ventilated area.
SAFETY INSTRUCTIONS SAFETY SYMBOLS This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER — ROTATING BLADES To reduce the risk of injury, keep hands and feet away.
SLOPE GAUGE (OK) Figure 1 Slope Gauge e da s h e d lin 15°/25% Slope 5% 15°/2 USE THIS SLOPE GAUGE TO DETERMINE IF A SLOPE IS TOO STEEP FOR SAFE OPERATION! To check the slope, proceed as follows: 1. Remove this page and fold along the dashed line. 2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.) 3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ). 4.
ASSEMBLY IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the Operation section of the Engine Manual before starting or running your machine. NOTE: Reference to right and left hand side of the Lawn Mower is observed from the operating position. Unpacking Opening Carton 1. Cut each corner of the carton vertically from top to bottom. 2. Remove all loose parts. 3. Remove loose packing material.
ASSEMBLY 5. Attaching the Grass Catcher The rope guide is attached to the right side of the upper handle. Loosen the wing knob which secures the rope guide. Refer to Figure 5. a. Hold blade control against upper handle. b. Slowly pull starter rope handle from engine and slip starter rope into the rope guide. See Figure 5. c. Tighten rope guide wing knob. 1. Follow steps below to assemble the grass catcher.
ADJUSTMENTS Attaching Side Discharge Cover Handle Pitch Your mower is shipped as a mulcher. To convert to side discharge, make sure grass catcher is off of the unit and rear discharge door is closed. For convenience of operation, you may adjust the pitch of the handle as follows: 1. Remove wing nuts and carriage bolts from handle. See Figure 11. 1. On the side of the mower, lift the mulch cover. See Figure 9. 2. 2.
OPERATION Blade Control Dual Lever Drive Control (Rear Wheel Drive Lever) Dual Lever Drive Control (Rear Wheel Drive Lever) Cutting Height Adjustment Lever Recoil Starter Grass Catcher Deck Wash Oil Fill Cap/Dipstick Rear Mulch Plug Trail Shield (Not Shown) Side Discharge Chute Cutting Height Adjustment Lever Figure 13 Blade Control Mulch Plugs The blade control is attached to the upper handle of the mower. Depress and squeeze it against the upper handle to operate the unit.
OPERATION GAS AND OIL FILL-UP IMPORTANT: Refer to the separate Engine Operator’s Manual for additional engine information. This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in this section before starting or running your machine. NOTE: Your mower is equipped with an advanced internal drive system for ease of use.
OPERATION 3. Using Mower as Front Wheel Drive Only. See Figure 16: a. b. Squeeze the left lever drive control against the upper handle to engage the front wheel drive. Release the left lever drive control to disengage the front wheel drive. NOTE: To disengage the front wheel drive (left lever) or rear wheel drive (right lever) while in four wheel drive perform the following. See Figure 18: • Allow the lever to move away from the upper handle.
SERVICE AND MAINTENANCE MAINTENANCE SCHEDULE Follow the maintenance schedule given below. This chart describes service guidelines only. Use the Service Log column to keep track of completed maintenance tasks. To locate the nearest Sears Service Center or to schedule service, call the following toll free number:1-888-331-4569. WARNING Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts have come to a complete stop.
SERVICE AND MAINTENANCE Engine Maintenance Refer to the Engine Operator’s Manual packed with your mower for a detailed description of all engine-related service specifications. Clean Engine • Daily or before every use, clean grass, chaff or accumulated debris from engine. Keep linkage, spring, and controls clean. Keep area around and behind muffler free of any combustible debris. • Keeping engine clean allows air movement around engine.
SERVICE AND MAINTENANCE Blade Care WARNING When removing the cutting blade for sharpening or replacement, protect your hands with a pair of heavy gloves or use a heavy rag to hold the blade. Place blade bell support on the blade. Align notches on the blade bell support with small holes in blade. 8. Replace hex bolt and tighten hex bolt to torque: 450 in-lb (min.), 600 in-lb (max.). To ensure safe operation of your mower, periodically check the blade bolt for correct torque.
OFF-SEASON STORAGE WARNING Never store lawn mower with fuel in tank indoors or in poorly ventilated areas where fuel fumes may reach an open flame, spark, or pilot light as on a furnace, water heater, clothes dryer, or gas appliance. Preparing The Engine Preparing The Lawn Mower For engines stored over 30 days: • Clean and lubricate mower thoroughly as described in the lubrication instructions. • Do not use a pressure washer or garden hose to clean your unit.
TROUBLESHOOTING WARNING Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. Before performing any type of maintenance/service, disengage all controls and stop the engine. Wait until all moving parts have come to a complete stop. Always wear safety glasses during operation or while performing any adjustments or repairs. This section addresses minor service issues.
TROUBLESHOOTING Problem Cause Remedy Excessive vibration 1. Cutting blade loose or unbalanced. 2. Bent cutting blade. 1. Tighten blade and adapter. Balance blade. 2. Replace blade. Uneven cut 1. Wheels not positioned correctly. 1. Adjust cutting height lever on right front and right rear wheel to same position. 2. Sharpen or replace blade. 2. Dull blade. Mower will not self propel 1. Belt not installed properly. 2. Debris clogging drive operation. 3. Damaged or worn belt. 1.
(This page applicable in the U.S.A. and Canada only.) Sears Brands Management Corporation (Sears), the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.S.
ÍNDICE Declaración de garantía. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Operación. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-32 Instrucciones de seguridad. . . . . . . . . . . . . . . . . . . . . . . . 22-25 Servicio y Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . 33-35 Pendiente De Calibre. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Almacenamiento fuera de temporada . . . . . . . . . . . . . . . .
INSTRUCCIONES DE SEGURIDAD ADVERTENCIA PELIGRO La presencia de este símbolo indica que se trata de instrucciones importantes de seguridad que se deben respetar para evitar poner en peligro su seguridad personal y/o material y la de otras personas. Lea y siga todas las instrucciones de este manual antes de poner en funcionamiento esta máquina. Si no respeta estas instrucciones podría provocar lesiones personales.
INSTRUCCIONES DE SEGURIDAD • Nunca opere la podadora en césped húmedo. Siempre esté seguro de su equilibrio. Si tropieza y cae puede lesionarse gravemente. Si siente que pierde el equilibrio, suelte inmediatamente la manija de control de la cuchilla y la cuchilla dejará de girar en tres segundos. • Corte el césped solamente con luz de día o con una buena luz artificial. Camine, nunca corra. • Detenga la cuchilla cuando cruce caminos de gravilla, pasos o andadores.
INSTRUCCIONES DE SEGURIDAD • Nunca recargue el tanque de combustible. Llene el tanque no más de 1 pulgada por debajo de la base del cuello de llenado para dejar espacio para la expansión del combustible. • No cambie la configuración del regulador del motor ni acelere demasiado el mismo. El regulador controla la velocidad máxima segura de operación del motor. • Vuelva a colocar la tapa de la gasolina y ajústela bien. • • Limpie la gasolina derramada sobre el motor y el equipo.
INSTRUCCIONES DE SEGURIDAD SÍMBOLOS DE SEGURIDAD Esta página representa y describe la seguridad los símbolos que pueden parecer en este producto. Lea, comprenda, y siga todas instrucciones en la máquina antes procurar para reunir y operar. Símbolo Descripción LEA EL MANUAL(S) DEL OPERADOR Lea, comprenda, y siga todas instrucciones en el manual (manuales) antes procurar para reunir y operar. PELIGRO— GIRANDO HOJAS Para reducir el riesgo de herida, guarde manos y pies lejos.
Figura 1 nua conti ea dis 15° lí n Las pendientes son un factor importante relacionado con resbalones y caídas de los accidentes que pueden resultar en lesiones o death.The severa máquina es pesada y puede acelerar cuando se va cuesta abajo. Esté preparado para mantener el control de la máquina. Para evitar la pérdida de control, operar a través de pendientes, no hacia arriba y hacia abajo. Al girar, girar hacia arriba, no hacia abajo. No utilice la máquina en pendientes superiores a 15 grados.
MONTAJE IMPORTANTE: Esta unidad se envía sin gasolina ni aceite en el motor. Antes de comenzar o correr la máquina cargue el motor con gasolina y aceite como se indica en la sección de operación de del manual de motor. NOTA: Las referencias a los lados derecho e izquierdo de la cortadora de césped se hacen observando la máquina desde la posición de operación. Desembalaje Apertura De La Caja De Cartón 1. Corte cada una de las esquinas de la caja verticalmente, de la parte superior a la base. 2.
MONTAJE 5. Conexión de la colectora de césped La guía de la cuerda, que está conectada a la varilla de sostén, se encuentra sobre el lado derecho de la manija inferior. Vea la Figura 5. a. Sostenga la manija de control de la cuchilla contra la manija superior. b. Jale la cuerda de arranque para sacarla del motor. Suelte el control de la cuchilla. c. 1.
AJUSTES Conexión de Canal de Descarga Lateral Inclinación de la manija Su podadora ha sido enviada como abonadora. Si hace la conversión a descarga lateral, asegúrese de que el colector de césped esté fuera de la unidad y que la puerta de descarga trasera esté cerrada. Por conveniencia de la operación, puede ajustar la inclinación de la manija de la siguiente manera: 1. Quite los tornillos y tuercas de mariposa transporte de manejar. Vea la Figura 11. 1.
OPERACIÓN Control de cuchilla Controles de transmisión de doble palanca� (Palanca de la tracción trasera) Controles de transmisión de doble palanca� (Palanca de la tracción trasera) Arrancador de retroceso Palanca de ajuste de altura de corte Lavado de la Plataforma Colector de Césped Tapón de aceite/varilla de medición del nivel de aceite Adaptador trasero para abono Escudo de Ruta (No Mostrada) Canal de Descarga Lateral Palanca de ajuste de altura de corte Figura 13 Control de Cuchilla Canal de D
OPERACIÓN Llenado de gasolina y aceite Consulte en el Manual del operador del motor información adicional sobre el motor. 1. Agregue el aceite provisto antes de arrancar la cortadora de césped la primera vez. 2. Realice el mantenimiento del motor con gasolina como se indica en el Manual del operador del motor. ADVERTENCIA: La gasolina es altamente inflamable y explosiva y usted puede quemarse o lesionarse gravemente al reabastecer. Pare el motor y mantenga lejos el calor, las chispas y las llamas.
OPERACIÓN b. Libere la palanca de control de transmisión izquierda para desacoplar la tracción delantera. a NOTA: Para desacoplar la tracción delantera (palanca izquierda) o la tracción trasera (palanca derecha), teniendo tracción en las cuatro ruedas, haga lo siguiente. Consulte la Figura 18: • Deje que la palanca se separe de la parte superior de la manija. • La palanca contraria se va a destrabar y separar de la manija, desacoplando la tracción.
SERVICIO Y MANTENIMIENTO PROGRAMA DE MANTENIMIENTO Siga el cronograma de mantenimiento que se presenta a continuación. Esta tabla sólo describe pautas de servicio. Utilice la columna Registro de Servicio para hacer el seguimiento de las tareas de mantenimiento completadas. Para ubicar el Centro de Servicio Sears más cercano o para programar un servicio, simplemente comuníquese con Sears al teléfono 1-888-331-4569.
SERVICIO Y MANTENIMIENTO Mantenimiento Del Motor 5. Arranque el motor como se describe en la sección de Operación. Consulte el manual del motor entregado con su bordeadora para obtener una descripción detallada de todas las especificaciones de servicio relacionadas con el motor. 6. Hacer funcionar el motor durante dos minutos como mínimo, permitiendo que la parte inferior de la plataforma de corte se lave a fondo. 7. Hoja de control de la cuchilla al parar el motor y la cuchilla. Motor 8.
SERVICIO Y MANTENIMIENTO Cuidado de la cuchilla ADVERTENCIA Cuando saque la cuchilla de corte para afilarla o reemplazarla, protéjase las manos usando un par de guantes para trabajo rudo o un trapo grueso para sostener la cuchilla. Inspeccione periódicamente el adaptador de la cuchilla en busca de rajaduras, especialmente cuando golpee un objeto extraño. Realice los reemplazos que resulten necesarios. Siga los pasos que aparecen debajo para realizar el mantenimiento de la cuchilla. 1.
ALMACENAMIENTO FUERA DE TEMPORADA ADVERTENCIA Nunca almacene la cortadora de césped con combustible en el tanque en un espacio cerrado o en áreas con poca ventilación, donde los gases del combustible puedan alcanzar el fuego, chispas o una luz piloto como la que tienen algunos hornos, calentadores de agua, secadores de ropa o algún otro dispositivo a gas.
SOLUCIÓN DE PROBLEMAS ADVERTENCIA Antes de realizar cualquier tipo del mantenimiento/servicio, suelte todos los mandos y pare el motor. Espere hasta que todas las partes de movimiento hayan venido a una parada completa. Desconecte el alambre de bujía y báselo contra el motor para prevenir el comienzo involuntario. Siempre lleve puestos cristales inastillables durante la operación o realizando cualquier ajuste o reparaciones. Esta sección se ocupa de cuestiones de menor importancia del servicio.
NOTAS 38
(Esta página se aplica sólo en EE.UU. y Canadá).
Product questions or problems? 1-888-331-4569 Customer Care Hot Line Get answers to questions, troubleshoot problems, order parts, or schedule repair service. Para respuestas a preguntas o problemas, y ordenar piezas o pedir servicio para la reparación de su equipo. To help us help you, register your product at www.craftsman.com/registration Para poderte ayudar mejor, registra tu producto en www.craftsman.