Operating instructions
Lightlyapplygreasetotheendofthearmonthetilt
anchorassemblyandinstallthetiltbracketassembly
tothearmusinga 1/2"x 1"hexbolt(C)and1/2"
nylockjamnut(O),Tighten.Loosenthenut1/4turn,
oruntilthetiltbracketassemblypivotsfreely,
Installa 1/4"x 1-3/4"hexbolt(H)througha 1/4"
washer(W)andthenthroughtheendoftheextension
springonthetiltbracketassembly,Next,insta!la 1/4"
hexnut(T)allthewayontothethreadsofthebolt,
Finallyinstalltheendoftheboltintotheholeinthe
armofthetiltanchorassemblyandsecureusinga
1/4"nylocknut(S).Tighten.
1/4" NYLOCK NUT (S)
TULTANCHOR
ASSEMBLY_
1/4" HEX NUT (T)
1/2" x 1"
REX BOLT (C)
1/4"'WASHER
\
APPLY
1/4"' x 1-3/4" GREASE
HEX HOLT (H) 1/2" NYLOCK
JAM NUT (O}
T{LT BRACKET
ASSEMBLY
FIGURE 6
STEP 9: iNSTALL DUMP CONTROL ROD
(SEE FIGURE 8)
, Install a 1/8" x 1-1/4" cotter pin (ll) into the inside hole
in each end of the dump control rod. Spread the ends
of the cotter pins and wrap around the rod. Instal! a
5/8" washer (BB) onto each end of the control rod.
Install the dump control rod to the dump pivot bracket
and bucket, Fasten using two 5/8" washers (BB) and
1/8" x 1-1/4" cotter pins (ll), Spread the ends of the
cotter pins and wrap around the rod,
1/8" x 1-114"
COTTER PiN (ii)
5/8" WASHERS (BE)
x 1°1/4"
COTTER
PiNS (H)
118" × 1-1/4"
COTTER PiN (H) DUMP
CONTROL
5/8" WASHERS (BE) ROD
FIGURE 8
STEP 8: iNSTALL DUMP PtVOT BRACKET
(SEE FIGURE 7)
" Install a 1/8" x 1-1/2" cotter pin (HH) to the inside hole
in the shaft shown in figure 7, and then install a 1"
washer (EE) onto the shaft. Apply grease to the end of
the shaft and install the dump pivot bracket assembly
onto the shaft. Install a 1" washer (EE) onto the shaft
and secure it using a 1/8" x 1-1/2" cotter pin (HH).
1/8" x 1ol/2"
COTTER PRN(HH)
\
/_/' 1" WASHERS (EE)
118" × 1-1/2"
COTTER PmN(HH)
DUMP PUVOT
BRACKET
STEP 10: INSTALL TILT STOP BRACKETS
(SEE FIGURE 9)
, Install a tilt stop bracket (OO) to each side of the
bucket using a 1/4" x 3/4" carriage bolt (K), 1/4"
washer (W) and 1/4" nylock nut (S). Do not tighten
the nuts until step 28.
TULTSTOP
BRACKET
1/4" NYLOCK _--.
NUT (S) 1/4" x 3/4" .j.l*_
114"WASHER (W) CARRmAGEBOLT (K)
FIGURE 9
FIGURE 7