Use & Care Manual

ManualsBrandsCraftsman ManualsChest & Cabinet CombosCraftsman 5-Drawer Standard Duty Ball-Bearing Tool Center - Black

Ball bearing Friction slides

OPERATOR’S MANUAL

F1842

Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA



 is used to indicate a hazardous situation which,

if not avoided, will result in serious injury or death.

 indicates a hazardous situation which, if not

avoided, could result in serious injury or death.

is used to indicate a hazardous situation which, if not

avoided, may result in minor injury, moderate injury, or property

damage.

 Read and follow all Safety Rules and Operating

Instructions before rst use of this product.

• Periodically the drawer fronts, drawer trim, and other surfaces

should be cleaned with a mild detergent and water.

• Auto wax will preserve the unit’s luster nish. Apply the wax as

to a car. The wax will also help protect the unit against scratches.

• Grease and oil can be removed with most standard cleaning

uids. For safety, use a nonammable cleaning uid.

• If drawer liners are supplied, it is recommended they are used

to protect the nish inside the drawers and to make the drawers

easier to clean. The drawer liners may be cleaned with soap and

water.

• For casters, use high quality bearing grease, (yearly).

• Lubricate the slides with grease or equivalent,(twice yearly.)



• Lubricate lock with graphite, (yearly).



• The maximum weight for each drawer should be no more than

25 lbs.

• Empty weight of the unit is: 70 lbs

• The maximum product weight, including contents, should be no

more than 400 lbs.

 Refer to Service

Parts Drawing for full listing of Service Parts.



Model numbers and other information required for service parts is

located on a label on top shelf behind the logo.



•  stand on this product. You may fall, which may cause

personal injury.

• step in drawers. You may fall, which may cause personal

injury.

•  when not moving this product. This will pre-

vent the product from rolling, which may cause personal injury or

product damage.

•  this product before moving with a

forklift.

•  tow with power equipment. The product could tip, which

may cause personal injury or prduct damage.



•  when removing or repositioning the

slides. The tool could slip, which may cause personal injury.

•  mount this product on a truck bed or any other moving

object. This may cause personal injury or product damage.

• alter this product in any manner. For example, do not

weld external lockbars or attach electrical equipment. This may

cause personal injury or product damage.

•  located on a level surface. The product may be-

come unstable and tip if stored or moved on an un-level surface,

which may cause personal injury or product damage.

• the drawers before moving this product. The drawers could

come open and make the product unstable and tip, which may

cause personal injury or product damage.

•  pull this product when moving it. Push the product to

prevent personal injury.



• when opening more than one drawer. The product

may become unstable and tip, which may cause personal injury or

product damage.



5-DRAWER BB TOOL CENTER - MODEL # 31013

Summary of content (8 pages)

PAGE 1
OPERATOR’S MANUAL Ball bearing 5-DRAWER BB TOOL CENTER - model # 31013 Friction slides • Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mild detergent and water. • Auto wax will preserve the unit’s luster finish. Apply the wax as to a car. The wax will also help protect the unit against scratches. • Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid.
PAGE 2
hardware ASSEMBLY TOOLS REQUIRED: Flat-tip Screwdriver 3/8-in Wrench Remove Chest From Roll-Away • The unit comes with the chest secured to the inside of the roll-away by either two or four 1/4-20 bolts. • Lay the roll-away down on its back. Use packaging material to protect the paint finish. • Remove the securing bolts from the underside of the roll-away. Save the screws for mounting the chest to the roll-away. • Remove the chest.
PAGE 3
Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops). Pull out to remove. • Attach the chest using two 1/4-20 screws that were used to secure the chest to the bottom of the roll-away. • Wrench tighten all screws. • Replace the drawer (refer to the drawer installation instructions). • To remove the chest, reverse the procedure.
PAGE 4
Removing and Installing Slides from Unit reinstall drawers Ball bearing slide - Pull slides and slide carrier out to fully extended position (see illustration). Hold the slide on the cabinet while aligning it with the slide on drawer. Slightly insert one side and repeat for the other side. Slowly push drawer to its fully closed position to engage slide. Open drawer and reclose to ensure proper operation. • First remove the drawer. (See section A) To remove the slide: • Push slide to the closed position.
PAGE 5
MANUAL DE USUARIO Cojinetes de bolas CENTRO PARA HERRAMIENTAS CON COJINETES DE BOLAS (BB, EN INGLÉS) DE CINCO CAJONES modelo no. 31013 Correderas de friccion • Lubrique la cerradura con grafito (anualmente). • Limpie con detergente suave y agua los frontales y los bordes laterales de los cajones y las demás superficies. • La cera para automóviles preservará el acabado brilloso de la unidad. Aplique la cera como lo haría al carro. La cera también ayudará a proteger la unidad contra raspones.
PAGE 6
FERRETERÍA ENSAMBLAJE HERRAMIENTAS NECESARIAS: QUITAR EL BAÚL DE LA PIEZA DESLIZANTE Destornillador, punta de cruz Llave Inglesa de 8mm • La unidad tiene un baúl fijado por dentro a una pieza deslizante ya sea por dos o cuatro pernos 1/4-20. • Acuesta la pieza deslizante boca arriba. Usa el material del empaque para proteger el acabado de la pintura. • Quita los pernos de fijación en el fondo de la pieza deslizante. Guarda los tornillos para montar el baúl sobre la pieza anterior. • Quita el baúl.
PAGE 7
Estilo palanca – Levante o baje (dependiendo de la corredera) • Fija el baúl con los dos tornillos 1/4-20 usados para unir el baúl al fondo de la pieza mencionada. • Aprieta todos los tornillos con una llave. • Vuelve a montar el cajón (ver las instrucciones correspondientes). • Para quitar el baúl, invierte el proceso. la palanca de liberación en ambos lados (esto permite que las correderas pasen sobre los topes). Jale hacia afuera para retirar.
PAGE 8
Estilo fricción - extienda completamente la gaveta. Inserte el destornillador en la ranura del costado y presione el tope hasta que libere el rejón. Hale la gaveta justo después del rejón antes de liberar el tope. Repita el proceso con la otra corredera QUITAR E INSTALAR LAS CORREDERAS DE LA UNIDA • Primero quita el cajón. (Ver la sección A) Para quitar la corredera: • Empuja la corredera hasta que quede en la posición de cerrado.