III ICRnFTSMnN® I 5.0 Horsepower 21 Inch Single Stage Auger Propelled Electric Start SNOW THROWER MODEL NO. 536.885212 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product. SEARS, ROEBUCK F-001128M AND CO., Hoffman Estates, IL 60179 UoS.A.
WARRANTY STATEMENT ...... SAFETY RULES ............... INTERNATIONAL SYMBOLS .... ASSEMBLY ................... OPERATION .................. MAINTENANCE ............... SERVICE AND ADJUSTMENT .. LIMITED TWO-YEAR 2 2 4 6 8 14 16 WARRANTY STORAGE TROUBLE ....... • i in Qio SHOOTING CHART REPAIR PARTS ............... ENGINE REPAIR PARTS SPANISH PARTS (ESPAI_IOL) .. 21 22 32 ....... 38 .......... ORDERING/SERVICE ON CRAFTSMAN 20 o Dloo. ..
TRAINING . 1. Read the operating and service instruction manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. 2. Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction. 3. Keep the area of operation clear of all persons, particularly small children and pets. 4. OPERATION 1.
13. Never operate the snow thrower near enclosures, automobiles, window wells, drep-offs, and the like without proper adjustment of the snow discharge angle. Keep children and pets away. 14. Do not overload the machine capacity by attempting to clear snow at too fast a rate. 15. Never operate the machine at high transport speeds on slippery surfaces, Look behind and use care when backing up. 16. Never direct discharge at bystanders allow anyone in front of the unit. 17.
Drive Clutch Forward Push To Engage Electric Starter Discharge DOWN Reverse Auger Clutch Fuel Discharge Auger Collector Oil UP Discharge Engage Fuel Oil Mixture LEFT Discharge RIGHT iN Weight Transfer Lift Handle To Engage Weight Transfer Depress Pedal To Disengage Transmission Ignition Key Insert To Run, Pull Out To Stop. SafetyWarningSymbols A DANGER Thrown Objects. Keep Bystanders Away. DANGER Thrown Objects. Keep Bystanders Away.
Contents of Parts Bag 1 - Owner's Manual (not shown) 1- Container 3.2 ounce Craftsman 2-cycle oil 1 - Electric Starter Cord (not shown) HOW TO CARTON safety glasses or eye shields _ ARNING: Always wear while assembling snow thrower. TOOLS REQUIRED 1 - Knif_ to cut carton FROM THE 1. Locate and remove container Craftsman 2-cycle oil. 2. Locate all parts packed separately and remove from the carton. 3. Remove and discard the packing material from around the snow thrower. 4.
_- CHECKLIST Before you operate your new snow thrower, to ensure that you receive the best performance and satisfaction from this quality product, please review the following checklist: P" All assembly instructions have been completed. _' The discharge chute rotates freely. P" No remaining loose parts in carton. While learning how to use your snow thrower, pay extra attention to the following important items: P" Make sure the fuel tank is filled with the correct mixture (40:1 ratio) of gasoline and oil.
KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Chute Deflector Ignition Switch Key Discharge Chute Choke Control Electric Starter Button Figure 2 Auger Drive Lever - Starts and stops the auger. Recoil Starter Handle - Starts the engine manually.
The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating the snow thrower. HOW TO THROW SNOW We recommend standard safety glasses or a wide vision safety mask for over your glasses. ,_ 1. Engage the auger drive lever. 2. To stop throwingsnow, release the auger drive lever.
FILL GAS: HOW TO MIX THE FUEL MIXTURE NOTICE: ENGINES WHICH ARE CERTIFIED TO COMPLY WITH CALIFORNIA AND US EPA EMISSION REGULATIONS FOR ULGE ENGINES: Are certified to operate on regular unleaded gasoline. Include the following emission control system(s): EM, TWC (if so equipped). Include any user adjustable features-therefore no other adjustments are needed. The two cycle engine, used on this snow thrower, requires a mixture of gasoline and oil for lubrication of the bearings and other moving parts.
mable. Always use caution ARNING: Gasoline is flamwhen handling or storing _ equipped three-wire WARNING: with Thea starter is power cord and plug and is designed to operate on 120 volt A.C. household current. The power cord must be properly grounded at all times to avoid the possibility of electrical shock which can injure the operator. Carefully follow all instructions in the "How To Start The Engine" section. Make sure that your house wiring is a three-wire grounded system.
grounded 120 VOLT,A.C. receptacle. (See the WARNING in this section). 8. Push the primer button while covering the vent hole as follows: Remove finger from primer button between primes. Do not prime if temperature above 50 ° F (10 ° C). tion. When the engine runs smoothly, move the choke control to the off position. NOTE: Allow the engine to warm up for several minutes before blowing snow in temperatures below 0°F. WARM START Push two time if temperature is 50 ° F (10 ° C) to 15°F (-10 ° C).
SNOW THROWING TIPS 10. After each snow throwing job, allow the engine to run for a few minutes. The snow and accumulated ice will melt off the engine. 11. Clean the snow thrower after each 1. When the handle is raised, the auger blades will engage the ground and the snow thrower will move forward. When the auger drive lever is released, the auger blades will stop. if the blades do not stop, see "How To Adjust The Auger Drive Cable" in the Service And Adjustment section. 2.
CUSTOMER RESPONSIBILITIES SERVICERECORDS Fill in dates as you complete regular service. Before Each Use Often Every 5 Hours Every 10 Hours Every 25 Hours Each Seat, on Before Storage SERVICE DATES -nghten All Screws and Nuts Check Spark Plug .j Lubricate Chute Control Flange Drain Fuel Check Fuel _J Check Auger Drive Cable Adjustment (See Cable Adjustment) .
HOW TO REMOVE THE TOP COVER 1. Remove the discharge Top Cover chute. 2. 3. Remove the fuel cap. Remove the two bolts and nuts (A) from the front of the top cover. 4. Remove the two bolts (B) from the left and right side of the top cover. D A 5. Remove the eight screws (C) on the left and right side of the top cover. 6, Remove the three screws (D) from the top portion of the control panel. 7. Carefully pull the rear of the top cover up and over the gas tank. 8.
the outer diameter tal starting when making any ,_ WARNING: To prevent accidenadjustments or repairs, always disconnect the spark plug wire and place it where it cannot make contact with the 4. of the worm gear. -tighten the nuts. spark plug. HOW TO ADJUST THE CHUTE CRANK Crank Adiusting Bracket If the chute crank will not rotate fully to the left or right, adjust as follows. 1. Remove the top cover. See "How To Remove The Top Cover". 2. Loosen the nuts. Worm Gear 3.
HOW TO REPLACE THE DRIVE BELT The drive belt is of special construction and must be replaced with original factory replacement belt available from your nearest Sears authorized service center. 7. Tip the auger enough to allow the auger to slide out of the auger housing. 8. To install auger, reverse the above steps. 1. Remove the belt cover. See "How To Remove The Belt Cover". 2. Remove the drive belt from the idler pulley (Figure 11). 3. Move the belt guide away from the belt. 4.
HOW TO ADJUST THE BRAKE PAD The brake pad is adjusted at the factory and a periodic adjustment is not necessary. . IMPORTANT: An adjustment is only necessary if the brake pad has become loose or has been removed. To adjust, proceed as follows: . 5. 1. Remove the top cover. See "How To Remove The Top Cover". 2. Remove the belt cover. See "How To Remove The Belt Cover". Tie the auger drive lever to the handle. This will engage the drive system.
TO ADJUST THE CARBURETOR The carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet. For operation at higher elevations, contact your nearest Sears Store. proper engine speed. Over-speeding the engine above the factory high speed setting can be dangerous. If the engine-governed high speed needs an adjustment, contact an authorized Sears Service Center. They have the proper equipment and experience to make any necessary adjustments.
To remove gasoline, run the engine until the fuel tank is empty and the engine stops. . snow thrower indoors or in ARNING: Never store your an enclosed, poorly ventilated area. If gasoline remains in the tank, fumes may reach an open flame, spark or pilot light from a furnace, water heater, clothes dryer, cigarette, etc. NOTE: To prevent engine damage (if snow thrower is not used for more than 30 days) follow the steps below.
TROUBLE CAUSE CORRECTION Difficult starting Defective spark plug. Replace spark plug. Water or dirt in fuel system. Use carburetor bowl drain to flush and refill with fresh fuel mixture. Engine runs erratic Blocked fuel line, empty gas tank, or stale fuel mixture. Clean fuel line; check fuel supply; add fresh fuel mixture. Engine stalls Unit running on CHOKE. Set choke lever to run or off position. Engine runs erratic; Loss of power Water or dirt in fuel system.
CRAFTSMAN 21" 5HP SNOW THROWER 536.885212 ELECTRIC START ASSEMBLY 16 16 17 930 313974C Key No. Part No.
CRAFTSMAN 21" 5HP SNOW THROWER 536.885212 FRAME ASSEMBLY 111 -- 110 116 116 100 117 91 113 102 90 92 KEY NO. PART NO. KEY NO. DESCRIPTION 80 FRAME, RIGHT SIDE 333769-853 109 NUT, 1/4-20 73826 81 FRAME, LEFT SIDE 333767 110 TANK, FUEL 1.5QT 90 91 92 CHANNEL, FRAME SCREW, 1/4-20X2.00 NUT, 1/4-20 333987 180044 782585 111 112 113 RING, FUEL TANK CAP, FUEL TUBING 333739 762224 100 BRKT, FUELTANK 333749-853 114 CLAMP, HOSE 323363 47345 101 SCREW, .
CRAFTSMAN 21" 5HP SNOW THROWER 536.885212 AUGER 511512 ASSEMBLY 483 510 48_482 483 520-10 531 534 540 541 520-2 492 520-8 333969 520 KEY NO. DESCRIPTION KEY NO. 340091 520 AUGER, ASSY 327072 302628 520-2 BLADE, AUGER 302565 71067 520-6 RIVET 49838 335992 DESCRIPTION PART NO.
CRAFTSMAN 21" 5HP SNOW THROWER HANDLE 536.885212 ASSEMBLY 760 764 752 762 753 334312A Key No. Description Part No. 740 CABLE, UPPER CONTROL 313449 741 LF BRKT, CABLE ADJ 313441 742 CABLE, LOWER CONTROL 313448 743 BOOT, CLUTCH 308146 744 SPRING, EXTENSION 313471 75O HANDLE, LOWER 333909-853 751 SCREW, 1/4-20Xl.25 313674 752 WASHER, FLAT. 71067 753 NUT, 1/4--20 782585 760 HANDLE, UPPER 333919-853 761 BAIL, CONTROL 333954-853 762 BOLT, 5/16-18X2.
CRAFTSMAN 21" 5HP SNOW THROWER 536.885212 CHUTE ROD ASSEMBLY 857 856 855 858 85O 851 852 334313 Key No. F-001128M Description Part No.
CRAFTSMAN 21" 5HP SNOW THROWER 536.885212 DISCHARGE CHUTE ASSEMBLY --582 342233 Key No. Description Part No. 580 RING, CHUTE 333859 561 SCREW 711752 582 GUIDE, CHUTE 577021 583 DONUT, FOAM 762173 590 CHUTE, LOWER 305862 591 SCREW, 1/4-20X .50 313686 592 NUT, CNTRLK 1/4-20 302635 600 CHUTE, UPPER WITH HANDLE 305861 601 WIRE 310562 602 BOLT, 5/16-18X1.
CRAFTSMAN 21" 5HP SNOW THROWER TOP COVER ASSEMBLY 536.885212 # 143 -,_ 1411 173 l 170 131 124 151 337370 181_ KEY NO. DESCRIPTION KEY NO. PART NO, 340097 146 HOSE, PRIMER 335507 DESCRIPTION 120 COVER, 121 SCREW, 1/4-14X.75 313685 147 NUT, 1/4-20 271172 122 PANEL, ACCESS 761538 150 COVER, BELT 340089 124 NUT, 1/4-10 578109 151 SCREW, 10-24X .50 12342 125 PANEL, CONTROL 761539-853 152 NUT, #10-24 312300 126 SCREW, 1/4-20X1.
CRAFTSMAN 21" 5HP SNOW THROWER ENGINE DRIVE ASSEMBLY 536.885212 79 10 76 11 78 7O 73 75 KEY NO. DESCRIPTION PART NO. 180077 45 46 PULLEY, iDLER SCREW 48924 302637 WASHER 120638 47 NUT 590 20 21 22 LF PAD, BRAKE SCREW WASHER 333970 180077 120638 48 50 51 WASHER, FLAT SCREW, 1/4-20X2.00 WASHER, FLAT 301188 180044 71067 23 SCREW,1/4-20X.
CRAFTSMAN 21" 5HP SNOW THROWER WHEEL ASSEMBLY 536.885212 651 61_0 661 314097 Description Key No. F--OO1128M Pa_ No.
F-OO1128M 31
CRAFTSMAN2-CYCLE ENGINEMODEL143.
CRAFTSMAN2-CYCLE ENGINEMODEL143.015071 KEY NO. PART NO. DESCRIPTION KEY NO. PART NO. RPM High 3700 to 4000 105 650892 Screw, 5/16-18 x 2-3/16" 106 650891 Screw, 5/16-18 x 1-5/8" 135 611049 Resistor Spark Plug (RCJ8Y) DESCRIPTION 1 250296A Cylinder Ass'y. (Incl.
CRAFTSMAN2-CYCLE ENGINEMODEL143.015071 m "15 ..) i _..
CRAFTSMAN2-CYCLE ENGINEMODEL143.015071 KEY NO. F-001128M PART NO. DESCRIPTION 0 640088 Carburetor (Incl. 184 of Engine Parts List) 1 632538 Throttle Shaft & Lever Assembly 6 631621 Throttle Shutter 7 650506 Shutter Screw 10 632734 Choke Shaft & Lever Assembly 14 631815 Choke Shutter 15 630735 Choke Positioning Spring 16 632164 Fuel Fitting 25 631951 Float Bowl Assembly (Incl.
CRAFTSMAN2-CYCLE ENGINEMODEL 143.015071 241_ 15 14 I I i i I I I I 19 1", I KEY NO. PART NO. 0 590670 Electric Starter (110 Volt) DESCRIPTION KEY NO. 13A PART NO. 590677 Thrust Spacer DESCRIPTION 1 34952 Retainer Ring 14 590659 Housing Ass'y.
CRAFTSMAN2-CYCLE ENGINEMODEL143.015071 _14 / 12! D8 Ii KEY NO. PART NO. 0 590743 Rewind Starter 11 590643 Starter HousingAss'y 3 590740 Retainer 12 590535 Starter Rope 6 590616 Starter Dog 13 590701 Starter Handle 7 590617 Dog Spring 14 590760 Spdng Clip 8 590645A Pulley & Rewind Spring F-OO1128M KEY NO. liil m7 DESCRIPTION 37 PART NO.
For the repair or replacement parts you need delivered directly to your home Call 7am-7pm, 7days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7days a week 1-800-4-REPAIR (1--800-473-7247) Para pedir servicio de reparacibn a domicilio- 1-800-676-5811 For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7days a week 1-800-488-1222 |||BBB mmmmmm For informa
