Operator`s manual

7. EngagetriggerIockonspraygunandstartengine
foliowinginstructionsHow to Start Your Pressure
Washer.
8£ If using cbaning tank, rotate detergentshut-off valve on
cleaning tank to "On" position (A).
/
J
iMPORTANT:if using detergent siphoning hose, makesure
detergent shut-off valve on cleaning tank is in the "Off"
position.
8B. If using detergentsiphoning hose, piacesmali fiiter end
of detergentsiphoning tube into detergentcontainer.
NOTE:Makesure the fiiter is fully submerged in detergent
while applying detergent.
NOTICE
Contact with the hot muffbr can damage detergent
siphoning tube.
Wheninsertingthe filterintoadetergentsolutionbottle,route
the tubeso asto keepit from inadvertentlycontactingthe hot
rnuffler.
9. Apply detergentto a dry surface, starting at lower
portion of area to be washedand work upward, using
long, even, overlapping strokes.
10. Aliow detergentto "soak in" for 3-5 minutes before
washing and rinsing. Re@plyas neededto prevent
surface from drying. DO NOTaiiow detergentto dry on
(prevents streaking).
iMPORTANT:When using the detergentsiphoning hose, you
must flush the detergent siphoning system after eachuse by
placing the fiiter into a bucket of cteanwater, then run the
pressure washer in Iow pressure for 1-2 minutes.
Pressure Washer Rinsing
After detergentis applied, scourthe surface andrinseit clean
as fellows:
f. if using cbaning tank, rotate detergentshut=off valve on
cleaning tank to "Off" position=
2. Rotate PrecisionSprayTM Selectorto a high pressure
position, asdescribed in the PrecisionSprayTM Selector
instruction sheet.
3. Keepspray gun a safe distance from spray surface.
WARNING
Kickbackfrom spray gun can causeyou to fall.
o Operatepressurewasherfrom astablesurface.
o Beextrerne[ycarefulif you mustusethe pressurewasherfrom
a ladder,scaffolding,or anyothersimilarlocation.
• Firmlygraspspraygunwithboth handswhenusing high
pressuresprayto avoidiniurywhenspraygunkicksback.
4. Apply a high pressure spray to a small areaand then
check the surface for damage.If no damage,proceedto
step 5.
Start at top of areato be rinsed, working down with
same overiapping strokes usedfor cleaning.
Cteaning Detergent $iphening Tube
If you used the detergentsiphoning tube, you must flush it
with clean water beforestopping the engine.
1. Engagetrigger iock on spray gun.
2. Piacedetergent siphoning tube/filter in a bucketfull of
ciean water.
3. Rotate PrecisionSprayTM Selector to a iow pressure
position, as described in the PrecisionSprayTM Selector
instruction sheet.
4. Flushfor 1-2 minutes.
5. Shut off engine foliowing instructions How to Stop
Pressure Washerand turn off water supply.
6. ALWAYS point gun in a safe direction and squeezespray
gun trigger to releaseretained high water pressure.
IMPORTANT:Spraygun traps high water pressure,evenwhen
engineis stoppedand water is disconnected.
WARNING
The high pressurestream of water that this
equipment produces cancut through skin and its
_ nderlying tissues, ieadingto serious injupj and
}ossible amputation.
Spray gun traps high water pressure, evenwhen
engine is stopped and water is disconnected,
which can cause injupJ.
o Keephighpressurehoseconnectedto purnpandspraygun
whilesystemis pressurized.
• ALWAYSpointsprayguninsafedirectionandsqueezespray
guntrigger,to releasehighpressure,everytimeyou stop
engine.Engagetrigger lockwhennot in use.
autematic Ceel gewn System {Thermal lleiief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reachtemperatures above
125%. The system engagesto cool the pump by discharging
the warm water onto the ground.
13