Owner’s Manual r B Q ETCIkJ O il ii ICH1 IAH in 6Ji HORSEPOWER 2200 PSI 2.2 GPM HIGH PRESSURE WASHER Model No. 580.762200 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions, HOURS: Mon. - Fri. 8 a.m. to 5 p.m, (CST) SEARS, ROEBUCK and CO., Hoffman Estates, IL 60179 U.S.A. Part No.
TABLE OF CONTENTS SAFETY RULES.......................................................................3 STORAGE ..............................................................................14 ASSEMBLY........................................................................ .4-5 TROUBLESHOOTING................... ....................................... .15 OPERATION ........................................................................ 6-9 REPLACEMENT PARTS ................................... ;........
SAFETY RULES CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PUCE WIRE WHERE IT CAN NOT CONTACT SPARK PLUG, TO PREVENT ACCIDENTAL STARTING WHEN SETTING UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS TO YOUR HIGH PRESSURE WASHER. CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions, WARNING; The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
ASSEMBLY CARTON CONTENTS HOW TO SET UP YOUR PRESSURE WASHER The following parts are shipped loose with your pressure washer: For tie most part, your Craftsman High Pressure Washer has been assembled at tie factory. You must, however, attach the wire form, assemble the spray gun, and attach tie high pressure hose to the pump and spray gun. • Main Unit — pressure washer with wheels, guide handle.
Cut ttie fe wraps on tie high pressure hose and connect high pressure hose to gun. Tighten by hand. Place assembled spray gun on holder. Place tuiho nozzle in grommet hole in base. Remove plastic cap and connect high pressure hose to pump. Tighten by hand. CHECKLIST Before you operate your new high pressure washer please review the following checklist ® All assembly instructions have been completed. Attach High Pressure hose here Attach nozzle extension to spray gun.
OPERATION KNOW YOUR HIGH PRESSURE WASHER Read this owner’s manual and safety rules before operating your high pressure washer. Compare the illustra tions with your high pressure washer to familiarize yourself with ttie locations of various controls and adjustments. Save this manual for future reference. Pump - Develops high water pressure. Enigine Throttle Confrol - Sets engine in starting mode for recoil starter; STOPS running engine. Primer Bulb — Prepares a cold engine for starting.
HOW TO USE YOUR PRESSURE WASHER IF YOU HAVE ANY PROBLEMS operating your pres sure washer, pleas© call the pressure washer helpline at 1-800-222-3136. A DANGER! NEVER adjust spray pattern when spraying. NEVER put hands In front of spray nozzle to adjust spray pattern. You could be injured. HOW TO USE THE ADJUSTABLE NOZZLE One of the nozzles you can attach to the nozzle extension is the adjustable nozzle.
RINSING WITH THE PRESSURE WASHER WARNING Be extremely careful if you must use the pressure washer from ladder, scaf folding or any otiier relatively unstable loca tion. Pressure in a running washer builds in the wand as you climb. When you press the trigger, tiie recoil from the initial spray could force you to fall, or if you are too close to tire cleaning surface, high pressure could force you off a climbing apparatus.
BEFORE STARTING THE PRESSURE WASHER TO START YOUR PRESSURE WASHER To operate the engine you will need to do the tjiowing: You have assembled your high pressure washer and have prepared the engine for starting. You are now ready to clean your car, boat or whatever you plan to clean. ADD ENGINE OIL Use only high quality detergent oil rated with API service classification SF or SG rated SAE 30 weight. Use no special additives.
® Turn on the water. IMPORTANT: Do not ain pump without the water sup ply connected and turned on. You must follow this cau tion or the pump will be damaged. « Move the Throtfle Control Lever to the ‘Fast’ position « Push primer bulb 3 times. Walt about two 2 seconds between each push. In cold weattier, (55“F/13°C or below) push 5 times. Note: Do not use primer to restart a warm engine after a short shut down.
AINTENANCE CUSTOMER RESPONSIBtUTtES MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE HOURLY OPERATING INTERVAL SERVICE DATES RESULAR SERVICE MAINTENANCE TASK Before Each Use Every 25 Hours or Yearly Every 100 Hours or Yearly PRESSUREWASHER Check/clean wafer inlet screen on quick-connect. xt Check high pressure hose. X Check detergenf hose. X Check spray gun and assembly for leaks. X Purge pump of air and contaminants. X ENGINE Check oil level. X Change engine oil.
BEFORE EACH USE ENGINE MAINTENANCE • Check water inlet screen for damage. CHECKING OIL LEVEL • • Check high pressure hose for teaks. Check detergent inlet hose and filter for damage. Oil level should be checked prior to each use or at least every 5 hours of operation. Keep oil level maintained. • Check gun and wand assembly for leaks. » Purge pump of air and contaminants. • Check engine oil level.
® Turn cover to ttie left {counterclockwise) and remove it and filter from flange. Discard filter. Shut off the engine and turn off the water supply. Separate the nozzle from the nozzle extension. ® Clean cover and flange thoroughly. Rotate to stream setting. ® Insert new filter into cover. Remove orifice from toe end of the nozzle using toe alien wrench included with the kit or a 2mm or 5/64 alien wrench.
1 O-Ring (p/n B2386) for the outside of the Male Quick-Connect 0-RING MAINTENANCE Through ttie noitnal operation of your pressure washer, O-Rlngs, which keep the connections of the hoses and gun fight and leak-free may become worn or damaged. Provided with your pressure washer is an 0-Ring Maintenance Kitwhidi provides replacement 0-Rings, Rubber Washer and Quick Connect filter. Parts in tiie 0-Ring Kit Include: » 2 0-Rlngs (p/n 97837) for each end of the nozzle extension.
STORAGE AFTER EACH USE To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Follow these instructions: Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and “freeze” pump action. Follow these procedures after every use: PROTECT FUEL SYSTEM ® Remove all gasoline from the fuel tank to prevent gum deposits from forming on these parts and causing pos sible malfunction of engine.
TROUBLESHOOTING PROBLEM Pump has following problems: CAUSE CORRECTION 1. Nozzle in low pressure mode. 1. Pull nozzle backward for high erratic pressure, chattering, toss of 2. Water inlet is blocked. 2. Clear inlet preraure, low water volume. 3. Inadequate water supply 3. Provide adequate water flow at failure to produce pressure, or pressure mode. least 2.2 gpm. 4. Inlet hose is kinked or leaidng 5. Replace/clean water inlet screen. 6. Water supply fe over 140°F. 6.
NOTES 17
PARTS CRAFTSMAN 3200 PSI HIGH PRESSURE WASHER 580.762200 Craftsman 4-Cycle Engine 143.
CRAFTSMAN 2200 PSI HISH PRESSURE WASHER 580.762200 Craftsman 4-Cycle Engine 143.986714 Item Part# 1 2 6 7 36835A 26727 33734 36557 12 12A 32447 36558 12B 14 16 16 17 18 36694 28277 30589 34839A 31336 651018 19 20 30 40 36281 32600 37208 35544A 40 35545A 40 35546 41 41 35541 35542 41 35543 42 42 42 43 45 35547A 35548A 35549 20381 32B75A 46 48 50 52 3261OA 35616 37011 29914 Description Cylinder (Incl. 2 &. 20) Dowel Pin Breather Element Breather Ass’y(incl.
CRAFTSMAN 2200 PSI HIC3H PRESSURE WASHER S80.762200 Craftsman 4-Cycle Engine 143.986714 Part# Description Qty. 155 157 16B 159 160 161 35624A 650914 36629 35626 35718 30063 1 1 2 1 1 178 29752 Rocker Arm Lock Nut Push Rod Rocker Arm Cover Gasket Rocker Arm Housing Screw, TofX T-30, 1/4-20 x1/2” Nut &. Lock Washer, 1/4-28 Screw, 1/4-28 X 1” Carburetor Gasket Intake Pipe Governor Link Spacer Control Bracket (Zncl.
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200 Craftsman 4“Cycle Engine 143.986714 Item Part# Description 0 640147 1 631615 16 17 631767 631184 631183 640070 650506 631807 651025 18 630766 20 640016 20A 640053 , Item Part# Qty. Carburetor Oncl.
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200 Craftsman 4-Cycle Engine 143.986714 ~u Item 0 3 6 7 8 11 12 13 14 Pari# Description 590739 590740 590616 590617 590618A 59063B 590535 590701 590741 Rewind Starter Retainer Starter Dog Doo Spring Qty- 1 1 2 2 1 Starter Housing Ass’yl40 degree grommet) Starter Rope (Length 98” x 9(64” dia.
CRAFTSMAN 2200 PS! HIGH PRESSyRE WASHER S80.76220H Craftsman 4“Cycle Engine 143.986714 Item 0 1 2 3 4 5 6 7 8 11 12 13 Parti Description 590702 590699A 590600 590696 590601 590697 590698 590699 590700 590703 590535 590701 Recoil Starter Spring Pin (Zncl. 4) Washer Retainer Washer Brake %)ring Starter Dog Dog Spring Puffey & Rewind Spring Ass’y. Qty.
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200 HIM 1 2 PART NO. 3 4 5 6 7 8 9 A1803C EB2534 39414 52858 42909 27007 B2142 1 1 3 5 2 2 2 10 11 12 13 14 15 16 17 18 19 20 75402 B2168 B1460 B1779 B2347 46476 51767 52857 92235 B1631A B2K3 2 21 22 23 24 25 B2626 91373 79552 96307 A1040B 1 B2619 om 1 1 1 3 2 2 2 2 2 1 1 1 1 1 1 1 DESCRIPTION BASE, VSFW ENGINE, TecumsehOHV 6.75HP PUMP, Medium Frame HANDLE HHCS.
o S I VENTURI ASSEMBLY p/H Baisi so ffi Os s SPACER PLATE ASSEMBLY P/N Baois TRAPPED P/N BÌ879 LINE PRESSURE outlet check valve assembly P/N Ae034 (NLCT CHECK VALVE ASSEMBLY P/N Aa033 unloader spindle assembly P/N Ba091 PUMP ICAD P/N BaOI4 assembly OTECK VALVE
CRAFTSMAN 2200 PSI HIGH PRESSURE WASHER 580.762200 Qty.
For the repair or replacement parts you need delivered directly to your home Cal! 7 am. * 7 p.m., 7 days a week 1 -800-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing agreement Call 9 a.m. - 5 p.m.
