Operators tVlanuai &75 Horsepower 2200 PSI 2.2 GPM ' ..... E WAS Model No. 580.762202 Pressure Washer Customer Hel 1-800-222-3136 HOURS: Mon.- Fri. 8 a.m. to 5 p.m. (CST) • • CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates, Visit our Craftsman website: www.sears.com/craftsman Part No. B3412 Draft 0 (7/30/98) Printed in the U,S,A.
SAFETY RULES ........................ 2-3 STORAG E ............................. 15 ASSEMBLY 4-5 TROUBLESHOOTING .................... 16 ................ 18-27 OPERATION ............................ .......................... MAINTENANCE ...................... LIMITED ONE YEAR 6-t 0 REPLACEMENT 11-14 WARRANTY PARTS HOW TO ORDER PARTS ..................
Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury. Always be certain the spray gun, nozzies and accessories are correctly attached. Never use a spray gun which does not have a trigger lock or trigger guard in place and in working order. Do not allow CHILDREN to operate the Pressure Washer at any time.
CARTON CONTENTS HOW TO SET UPYOUR PRESSURE WASHER The following parts are shipped loose with your pressure washer: o Main Unit -- pressure washer with wheels, guide handle. • High Pressure Hose For the most part, your Craftsman High Pressure Washer has been assembled at the factory. You must, however, attach the wire form, assemble the spray gun, and attach the high pressure hose to the pump and spray gun.
Cut the tie wraps on the high pressure hose and connect high pressure hose to gun. Tighten by hand, o Place assembled spray gun on holder. o Place turbo nozzle in grommet hole in base. Remove plastic cap and connect high pressure hose to pump, Tighten by hand, CHECKLIST Before you operate your new high pressure washer please review the following checklist: o All assembly instructions have been completed.
KNOW YOUR HiGH PRESSURE WASHER Read this owner's manual and safety rules before operating your high pressure washer. Compare the illustrations with your high pressure washer to famiIiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
HOW TO USE YOUR PRESSURE WASHER IF YOU HAVE ANY PROBLEMS operating your pressure washer, please call the pressure washer helpline at 1-800-222-3136. HOW TO USE THE ADJUSTABLE NOZZLE A DANGERt NEVER adjust spray pattern when spraying. NEVER put hands in front of spray nozzle to adjust spray pattern. You could be injured. One of the nozzles you can attach to the nozzle extension is the adjustable nozzle.
RiNSiNG WITH THE PRESSURE WASHER WARNING Be extremely careful if you must use the pressure washer from ladder, scaffolding or any other relatively unstable location. Pressure in a running washer builds in the wand as you climb. When you press the trigger, the recoil from the initial spray could force you to fall, or if you are too close to the cleaning surface, high pressure could force you off a climbing apparatus.
TO START BEFORE STARTnNG THE PRESSURE WASHER ODL Use only high quality detergent oil rated with API service classification SF or SG rated SAE 30 weight, Use no special additives, Check that the high pressure hose is tightly connected to the spray gun and to the pump. See ASSEMBLY section for illustrations. Clean area around oil fill and remove oil dipstick. Wipe dipstick clean.
HOW TO STOP YOUR WASHER IMPORTANT: Do not run pump without the water supply connected and turned on. You must follow this caution or the pump will be damaged. Move the Throttle Control Lever to the 'Past' position o Push primer bulb 3 times. Wait about two 2 seconds between each push. In cold weather, (55°F/13°C or below) push 5 times, Note: Do not use primer to restart a warm engine after a short shut down.
CUSTOMER ............... RESPONSiBiLiTiES MAINTENANCE SCHEDULE HOURLY OPERATING INTERVAL FILL IN DATES AS YOU COMPLETE REGULAR SERVICE MAINTENANCE Before Each Use TASK PRESSURE WASHER Check/clean water inlet screen I Every 100 Hours or Yearly xf on quick-connect, ;Check Every 25 Hours or Yearly SERVICE DATES x high pressure hose, ................ ,,,,,,,,,,,,,,, ......... Check detergent x hose. i Check spray gun and assembly x for leakS:.
BEFORE o • , • • Check Check Check Check Purge Check EACH USE ENGINE water inlet screen for damage. high pressure hose for leaks. detergent inlet hose and filter for damage. gun and wand assembly for leaks. pump of air and contaminants. engine oil level. PRESSURE WASHER CHECKING OIL LEVEL Oi! level should be checked prior to each use or at least every 5 hours of operation. Keep oil level maintained.
Turn cover to the left (counterclockwise) and remove it and filter from flange. Discard filter. o • Shut off the engine and turn off the water supply. Separate the nozzle from the nozzle extension. Clean cover and flange thoroughly. Rotate to stream setting. Insert new filter into cover. Remove orifice from the end of the nozzle using the allen wrench included with the kit or a 2ram or 5/64 allen wrench.
O-RING MAINTENANCE 1 O-Ring (pin B2386) for the outside of the Male Quick-Connect. Through the normal operation of your pressure washer, O-Rings, which keep the connections of the hoses and gun tight and leak-free may become worn or damaged. Provided with your pressure washer is an O-Ring Maintenance Kit which provides replacement O-Rings, Rubber Washer and Quick Connect filter. Parts in the O-Ring • 2 O-Rings extension.
AFTER EACH USE Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and "freeze" pump action. Follow these procedures after every use: To avoid engine probfems, the fuel system should be emptied before storage of 30 days or longer. Follow these instructions: PROTECT FUEL SYSTEM Remove all gasoline from the fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine.
PROBLEM CAUSE CORRECTION 1. Nozzleinlowpressure mode. t. Pull nozzle backwardfor high erraticpressure,chattering,loss of 2. Waterinletis blocked. 2. pressure mode. Clear inlet pressure,low watervolume. 3. Inadequatewatersupply 3. Provide adequatewater flowat least22 4, inlet hoseis kinked or leaking 4. gpm, Straighteninlethose,patch leak, 5. Cloggedwaterinletscreen. 5. Replace/ clean waterinletscreen. & 7. Watersupply isover t40°F. Outiethoseis blocked. 6. 7.
CRAFTSMAN 2260 PSI HIGH PRESSURE WASHER 580.
CRAFTSMAN 1 3 4 5 6 7 8 9 10 11 12 !3 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 3t 32 33 35 36 2200 PSB HBGH PRESSURE PART NO.
CRAFTSMAN 2200 PSi HiGH PRESSURE WASHER 580,762202 L_ o_ or, _o_ 04 o_ __, o_ 4_ 37 44 - 5Z 43 8 /.
CRAFTSMAN 2200 PSi HIGH PRESSURE WASHER item _ 1 2 3 B2218 B2260 96542 1 1 1 4 5 B3328 97606 ! 1 6 7 8 9 10 11 12 B2261B B2217 94944 99427 96400 99735 93790 4 4 3 3 3 t 1 13 !4 15 B2016 93668 40945 16 17 18 93652 95416 93876 1 3 6 1 1 t9 2O 21 22 23 24 25 26 27 28 B2015 #2069 97934 B1449 93644 96053 96015 95380 95379 A1575 1 1 1 6 6 1 3 3 1 1 ! 580.762202 O-RING, 1.625" x 0.103 Item 29 B2451 1 VENTURI ASSEMBLY ADAPTER, Engine BEARING, Eng. Adptr. Roller Thrust 4 x 4 CAM, Axial 6.
CRAFTSMAN Tecumseh 2200 PSi HIGH PRESSURE 4-Cycle Engine WASHER 580.762202 143.
CRAFTSMAN Tecumseh Item 2200 PSi HgGH PRESSURE 4=Cycne Engine WASHER 580,762202 143,9867t4 Part# Description Qty. 1 2 6 7 36835A 26727 33734 36557 1 2 1 12 12A 32447 36558 12B t4 15 16 17 18 36694 28277 30589 34839A 31335 651018 19 20 30 40 36281 32600 37208 35544A 40 35545A 40 35546 41 41 35541 35542 41 35543 42 42 42 43 45 35547A 35548A 35549 20381 32B75A 46 48 50 52 32610A 356!6 37011 29914 Cylinder (Incl. 2 &. 20) Dowel Pin Breather Element Breather Ass'y. (Inc!.
CRAFTSMAN Tecumseh Item 2200 PSi HiGH PRESSURE WASHER 580.762202 4=Cycne Engine 143.
CRAFTSMAN Tecumseh 2200 PSi HUGH PRESSURE 4_Cycle Engine WASHER 580.762202 143.986714 t I 37 P Item 0 Part# Description 64O t 47 Carburetor ncl.
CRAFTSMAN Tecumseh 2200 PSI HIGH PRESSURE 4-Cycle Engine WASHER 580,762202 143.986714 / 1 t3 f f \ _8 % J m m -7 @-, item 0 3 6 7 8 1t 12 13 14 Part# Description 590739 590740 590616 590617 590618A 59063B 590535 590701 590741 Rewind Starter Retainer Starter Dog Dog Spring . , =Pulley k Rewind Spr!ng Ass y =Starter Housing Ass y -(4,0 degre,egrommet) Starter Rope (rengtld 98 x 9(64 dia.) Starter Handle Locking Tab Qty.
For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4=MY=HOME Para pedir servicio de reparaci_n (1-800 69-4663) a domicilio = 1-800-676o5811 in Canada for all your service and parts needs call = 1-800-665=4455 Au Canada pour tout le service ou los pieces For the repair or replacement parts you need: Call 7 am - 7 pm, 7 days a week 1=800=366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio = 1-800-659-7084 For the location of a Sears Parts and Repair Ce
