Operators Manual 2.5 GPM HIGH PRESSURE WASHER CLEANING SYSTEM Model No. 580.768030 HOURS: Mon. - Fri. 8 a.m. to 5 p.m. (CT) CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179 Visit our Craftsman website: www.sears.GomJcmftsmen Part No. B3595 D_tt $ (4/5/1999) Pr;.rttsd in _ U.S.A.
Warranty ......................... Safety Instructions ................ Assembly ......................... Operation ....................... Maintenance .................. Storage 2 2-3 4 5-9 10-13 ......................... LIMITED Troubleshooting ................... Replacement Parts .............. Emission Control Warranty Statement ............. How to order parts and request service .............
• Operateengineonlyatgovemedspeed.Running theengineat excessive speeds increases the Never use a spray gun which does not have a trigger look or tdgger guard in place and in working order. hazard of personal injury. Do not tamper with parts which may increase or decrease the governed speed. • Use a respirator or mask whenever there is a chance that vapors may be inhaled. Read at! instructionswith the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors.
CARTON • CONTENTS Raise guide handle, secure in place. Roll the cleaning system out the open end of the carton. The tollowing parts are shipped loose with your cleaning system: • Main Unit -- pressure washer with wheels, chemical tanks, guide handle.
KNOW YOUR HIGH PRESSURE WASHER Read this owner's manual and safety rules before operating your cleaning system. Compare the illustrations with your cleaning system to familiarize yourself with the ocations of various controls and adjustments.
HOW TO USE YOUR CLEANING SYSTEM Cleaning With The Adjustable Nozzle and Applying Chemical Read these instructions and learn how to use your cleaning system before you attempt to start your cleaning system. If you have any problems operating your cleaning system, please call the pressure washer helpline at 1-800-222-3136. IMPORTANT: Use soaps designed specifically for pressure washer cleaning systems. Household detergents could damage the pump.
,_ Warning: Besystem extremely careful if you must use the cleaning from a ladder, scaffolding or any other relatively unstable location. When you press the trigger, the recoil from the initial spray could force you to fall, or if you are too close to the cleaning surface, high pressure could force you off a climbing apparatus. • • Rotate the Dial-A-Cleaner TM selector knob to the letter corresponding to the System Rinse tank.
Toaddfueltoengine: • Clean area around fuel cap, remove cap. • Add regular unleaded gasoline, slowly, to the fuel tank. Important: Never mix oil with gasoline. • Install fuel cap and wipe up any spilled gasoline. TO START THE CLEANING SYSTEM Safety Latch The best way to start your cleaning system engine for the first time is to follow these instructionsstep-bystep. This starting information also applies whenever you start the engine after you have let the cleaning system sit idle for at least a day.
• Grasp starter handle and pull slowly until you feel some resistance. Then pull cord rapidly to overcome compression, prevent kickback and start the engine. Let rope return to starter slowly. Note: The Pressure Command TM may be placed in any position during starting or operation. • When engine starts, move choke lever to "1/2 CHOKE" until engine runs smoothly and then to "NO CHOKE POSITION." If engine falters, move choke lever to =1/2 CHOKE" until engine runs smoothly and then to "NO CHOKE POSITION.
CUSTOMER RESPONSIBILITIES HOURLY OPERATING INTERVAL MA|t_RENANCESCHEDULE RLL iN DATESAS YOU COMPLETE REGULARSERVICE Before MAINTENANCE TASK Es_tl Use J HOURS or Hours Eve/'] 50 Yearly SERVICE DATES O_ Evee/100 Yearly PRESSURE WASHER Check/clean water inlet screen onquick-connect. Checkhighpressure hose. xt x Check detergent hose, x Check spray gun and assembly for leaks. x Purgepumpofairandconterninants. ENGINE Checkoillevel. x ' x x* oil. Serviceair cleaner.
BEFORE EACH USE • Check water inlet screen for damage. • Check high pressure hose for leaks. • Check chemical tanks and filters for damage. • Check gun and wand assembly for leaks. Purge pump of air and contaminants. • Check engine oil level. PRESSURE WASHER Check and Clean If the screen is damaged, the o-ring kit contains a replacement in-line filter screen and an o-ring. If undamaged, reuse screen. 3. Place the in-line filter screen into the threaded end of the lance.
Usethewireincludedinthe kitor a small paper Parts in the O-Ring ICJtInclude: clip to free the foreign materials clogging or restricting the nozzle. • 1 O-ring, red, (p/n B2726) for the end of the spray gun connection between gun and highJ1owspray wand. • 2 O-rings, yellow, (p/n B2264) for the ends of the high pressure hose. Insert wire into nozzle and turn back and forth to clear obstruction. Remove additional debris by back flushing water supply through wand. Back flush between"30 to 60 seconds.
ENGINE MAINTENANCE Base Maintenance, replacement or repair of the emission control devices and systems may be performed by any non-road engine repair establishment or individual. Paper Element Checldng Oil Level Oil level should be chocked prior to each use or at least every 5 hours of operation. Keep oil level maintained. Bas_ Changing Oil Change engine oil after the first two hours and ,every 50 hours thereafter.
AFTER EACH USE Flush the chemical system by selecting a tank and run the Pressure Washer with nozzle in low pressure mode. Flush until each tank is empty, then switch the selector knob to the next tank. The last tank to be emptied must be the System Rinse tank. Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and "freeze" pump action.
CAUSE PROBLEM CORRECTION Pump has toilownng problems: 1. Nozzle in tow pressure mode. 1. Pull nozzle backward for high failure to produce pressure, or erratic pressure, chattedng, loss of 2. Water inlet is blocked. 2. pressure mode. Clear inlet pressure, Lowwater volume. 3. Inadequate water supply 3. Provide adequate water flow at least 3 gpm. 4. 4. Straighten inlet hose, patch leak. 5. Clogged water inlet screen. 5. Replace / clean water inlet screen. 6. Water Supply is over 140°F. 7.
Tecumseh 6HP Enduro, Model #143.
Tecumseh 65 6HP Enduro, Model #143.
Tecumseh ]_ 2 14 15 16 19 20 25 25A 26 30 35 37 38 40 40 41 41 6HP Enduro, 37120A 26727 651052 37108 37110 37111 32600 36621 36622 30200 34740 651053 29216 37109 40004 40005 36070 36071 42 42 43 45 40006 40007 20381 32875A 46 48 49 50 60 64 65 69 70 72 75 80 81 82 83 86 89 90 92 93 100 101 103 103A 110 110A 111A 119 120 125 125 32610A 35616 36611 37040 36623A 651015 30200 36624 36766 27642 36742 30574A 30590A 30591 36057 650488 610961 611205 650815 650818 34443B 610118 651007 650767 35589 36964 61122
Tecumseh 6HP Enduro, Model #143.996005 Item Pa_# 0 640O6O 2 '20A ] 30 _b_.37 .dD_37 - 25 20 1 2 4 5 6 7 10 11 12 13 14 15 16 17 631615 631767 631184 631183 631036 650506 31868 632042 631184 631183 631890 630735 632164 651025 18 20 20A 25 27 28 29 30 31 36 37 40 44 47 48 60 630766 640027 640053 631867 631024 632019 631028 631021 631022 640019 632547 640015 27110A 630748 631027 832760 Carburetor (Incl.
Tecumseh 6HP Enduro, Model #143.996005 _em Pa_# 0 1 2 3 4 5 6 7 8 11 12 13 F 21 590736 590599A 590600 690696 590601 590697 590698 590699 590700 590705 59O535 59O701 Qty. Rewind Starter Spring Pin (Incl. 4) Washer Retainer Washer Brake Spring Starter Dog Dog Spring Pulley & Rewind Spring Ass'y. Starter Housing Ass'y. Starter Rope (98" x 9/64" dia.
Craftsman Pump 2250 PSI Cleaning System 580.
Craftsman 2250 PSI Cleaning System 580.768030 Pump Nern Part# Qtv Descr_bn Item Pad# 1 B2218 1 O-RING, 1.625"x 0.103 33 ... 2 3 4 5 6 7 8 9 10 11 12 B2260 B2217 B2261B 96400 99735 93790 40945 93652 95416 93876 A2069 1 4 4 3 1 1 6 1 1 1 1 ADAPTER, Engine O-RING, 0239 ID x 0.0-/0 SCREW, ButtonHd 5/16 - 24 x 3/4" Lg SPRING, PistonReturn ASSEMBLY,Oil Bmalher O-RING, 114x 119x 2.6 SHCS, M6 x 1.0 x20mm Lg SPRING, ThermalBy-Pros ' P_STON,_ By-Pass O-RING, Z9 x 6.5 x 1.
Craftsman Main Unit 2250 PSI Cleaning System 580.
Craftsman Main Unit 2250 PSI Cleaning Item Part_# System 580.768030 Qtv 2 3 4 5 B3608C B3597 B3376B B32?.
CALIFORNIA & US EPA EMISSION CONTROL WARRANTY STATEMENT You are responsible for presenting your utility or lawn or garden equipment engine to a Tecumseh Authorized Service Outlet (any Tecumseh Registered Service Dealer, Tecumseh Authorized Service Distributor or Tecumsoh Central Warehouse Distributor) as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. The U.S.
EMISSION CONTROL SYSTEM WARRANTY 4. Repair or replacement of any warranted, emissions related part under this ECS Warranty shall be performed at no charge at a Tecumssh Authorized Service Outlet. Emission Control System Warranty (=ECS Warranty') for 1995 and later model year Califomia utility and lawn and garden equipment engines (for other states, 1997 and later model year engines): 5.
I For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME" Para (1-800-469-4663) pedir servicio de reparack_n a domicilio - t-800-676-5811 In Canada for all your service and parts needs call - 1-800-665-4455 Au Canada pour tout fe service ou les pi_ces For the repair or replacement parts you need: _Call 7 am - 7 pm, 7 days a week 1-800-366-PART Para ordenar (1-800-366-7278) piezas con entrega a domicilio- 1-800-659-7084 For the location of a Sears Parts and Rep