Manual

CJeaningand ApplyingDetergent with the StandardClear
Siphon
To apply diluted detergent using the
standard clear siphon tube, follow these
steps:
1. Review use of PrecisionSprayTM
nozzles.
2. Attach clear siphon hose to barbed
fitting on pump.
3. Mix detergent solution as required by job.
4. Place small filter end of clear siphoning tube into
container with diluted solution as described above.
NOTE:DO NOTinsert standard siphon hose in Extreme
Concentrate. Failureto dilute concentrate will causeexcessive
application and consumption of solution.
NOTE:Makesure the filter is fully submerged in fluid while
applying solution.
NOTICE
Contact with the hot muffler can damagedetergent
siphoning tube.
Wheninsertingthe siphonintoa detergentsolutionbottle,
routethetubeso asto keepit from inadvertentlycontactingthe
hot muffler.
5. Make sure fan soap (black) or jet soap nozzle (magenta)
is installed.
NOTE:Detergentcannot be applied with the high pressure
nozzles (Cyan, Orangeor Red).
6. Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE
You must attach all hoses before you start the engine.
Startingthe enginewithoutallthe hosesconnectedandwithout
the waterturnedONwill damagethe pump.
Damageto equipmentresultingfrom failureto followthis
instructionwill void warranty.
7. Start engine following instructions How to Start Your
Pressure Washer.
8. Apply detergentto a dry surface, starting at lower
portion of area to be washedand work upward, using
long, even, overlapping strokes.
9. Allow detergentto %oak in" for 3-5 minutes before
washing and rinsing. Reapplyas neededto prevent
surface from drying. DONOTallow detergentto dry on
(prevents streaking).
IMPORTANT:You must flush the detergent siphoning system
after each use by placing the filter into a bucket of clean
water, then run the pressure washer in low pressure for 1-2
minutes.
Pressure Washer Rinsing
ForRinsing:
1. Remove lowpressure nozzlefrom nozzleextension.
2. Selectand installdesired high pressure nozzlefollowing
instructions How to UsePrecisionSpraSMNozzleSystem.
3. Keepspray gun a safe distance from areayou plan to
spray.
spray gun can causeyou
Kickbackfrom to fall.
• Operatepressurewasherfrom astablesurface.
, Beextremelycarefulif you mustusethe pressurewasherfrom
a ladder,scaffolding,or anyothersimilarlocation.
, Firmlygraspspraygunwith both handswhenusing high
pressuresprayto avoidinjurywhenspraygunkicksback.
Apply a high pressure spray to a small areaand then
check surface for damage.If no damage is found, you
can assume it is okayto continue rinsing.
Start at top of areato be rinsed, working down with
same overlapping strokes as you used for cleaning.
Cleaning DetergentSiphoning Tube
If you used the clear detergent siphoning tube, you must
flush it with clean water before stopping the engine.
1. Placedetergent siphoning tube/filter in a bucket full of
clean water.
2. Remove high pressure nozzlefrom nozzleextension.
3. Selectand install a soap nozzlefollowing instructions
How to Use PrecisionSprayTM Nozzle System.
4. Flushfor 1-2 minutes.
5. Shut off engine following instructions How to Stop
Pressure Washerand turn off water supply.
6. ALWAYS point spray gun in a safe direction push red
button and squeezespray gun trigger to release retained
high water pressure.
iMPORTANT:Spray gun traps high water pressure, even
when engine is stopped and water is disconnected.
Automatic Cool Down System (Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F.The system engagesto cool the pump by discharging
the warmwater ontothe ground.
15