Sears. Roebuck and Co., Chicago, IE. 60684 US. A.
/ ,i‘‘.....' ■' ■ ■ \- у» r ■.'7 \ ^ ,. ,fr-:^ \/г X- ,,г'i^.N X.>''"*'KV,X . -/‘¡fy • V,XXyX-;*—‘V-.X ‘‘-"i.. • '' ^ Щ^Щ0!^ •i»r TWO YEAR LIMITED WARRANTY ON CRAFTSMAN BUSHWACKER 836.796670 For two years from date of purchase, when this BUSHWACKER is maintained, lubricated, and tuned up accordtrtg to the operating and maintenence instructions in the owner's manuai. Sears will repair free of charge any defect in material or workmanship This warranty excludes blades, spark plug.
Know ¥OyR BUSHWACKER Your new BUSHWACKER has been carefuhy packed at the factory to prevent damage during shipping and storage, however, even with the best of preventative measures, damage does sometimes occur It is recommended that you follow the check out procedures listed below: _ Remove all items from the carton, lay them out and check the parts to be sure that you have everything required for assembly. Also check carefully for any visible damage..
PREP4B1MG FOR OPERATIOM Fuai and oil mixture inspect the fuel tank and fill with clean, fresh fuel of the proper mixture This engine requires a mixture of 16 parts gasoline to 1 part oil |1 gal gasoline to 8 oz oil) Use 71-36555 Craftsman Engine Oil or a high grade two cycle engine oil.
3. . Puii the throttle lever a little, push the throttle knob and lock the throttle lever at the starting position, (Figure 31 without a load, otherwise the engine will run at a high speed reducing engine life. Stopping the Engine 1 Reduce the engine rpm to idle by releasing the throttle 2, Set the stop switch to stop. (Figure 1) Blade sharpening If the edges are rounded and do not cut well arty more, grind off only the shaded portions.
Carburetor Proper adjustment of the carburetor is very important to the operation of this engine. The carburetor has been carefully adjusted at the factory and therefore should not require any further adjustment,. SLAiSB AWUSTMSMT (Performed with engine stopped.) The blades wear with use when you notice a decrease in cutting performance adjust the blades as follows.
mSMTEH^WeE 1, In every 10--20 hours. Inject one or two ounces of grease through a grease nipple installed in the gear case of the BUSHWACKER- Be sure the engine is stopped while greasing the gear case 2 Stop the engine before lubricating the blades during the cutting c>peration. Frequent lubrication using a light weight oil during cutting will greatly add to blade life.
SEARS BUSHWACKER PARTSLIST-MODEL 636.
SEARS BUSHWACKER PARTSLIST-MOOEL 636.786670 FiBure 7 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 IS 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 PART NO, 118-110 900-140/0 118-121 118-111 118-001 118-115 302-050 118-112 118-114 118-113 118-109 SOO-141/1.
SEARS BUSHWACKER PARTSLIST-MODEL 636.
SEARS BUSHWACKER PARTSLIST-MODEl. 638.796670 Fi^re B KEY NO. 1 2 3 4 S 6 7 8 9 10 It 12 13 14 15 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 3? 38 39 40 41 42 43 44 45 PART NO. QTY.
SEARS BUSHWACKER PARTSLIST-MODEL 636.
SEARS BUSHWACKER PARTSLIST4W0DEL 636.736670 Figure 3 KEY NO. •1 *2 3 4 S 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2S 26 27 28 29 30 31 32 33 PART NO. EC02ER-0606 34Í14 S-2238 92-258 95-99 157-280 92-257 92-146. 95-526 21-168 122-211 16-103 112-183 16-104 16-71 136-90 52-30 167-91 98-323 96-314 96-323Y 96-325Ì^ EC02E-3123 EO)2E-3104a EC02E-3108 EC02E-3141A EC02E-3114A ECQ1A-3072A eC02E-310G EC02ER-3130 00436-a512-0 h) 00217-05000 N 00431-0555-0 M QTY.
The Model Number will be found on the top of recoil starter. Always mention the Model Number when requesting service or repair parts for your unit. All parts listed herein may be ordered from any SEARS, ROEBUCK AND CO. OR SIMPSONS'SEARS LIMITED service units or most retail stores. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION AS SHOWN IN THIS LIST 1. ThePART NUMBER 3 The PART DESCRIPTION 2 The MODEL NUMBER 4, The NAME OF ITEM- of the Bushwacker 63B. 796670 20.