NB04D-9150/I Sears] owner's manual MODEL NO. 636.795454 I:RRFTSM 37.7 cc CAUTION: Read Rules for Safe Operation and Instructions GASBRUSHWACKEWo". • Assembly • Maintenance • Operation • Repair Parts Carefully Sears, NB04D.9150/| 6/82 Roebuck and Co., Chicago, Ill. 60684 PRINTED U.S.A.
° _...... _'_ :1'"Y'E-,_.R'_WA_ R_A-N T_'_O N CR_'A:I= TS A_N M _'-'_" _ _""_ _SHWACKER _M• 636. 795454 _CKER_M.• fails to perform properly, due toa defect in material or workmanship with_ in one (1) year from date of purchase Sears will repair it free of charge c ase, Sears will rep_ , • _TM. is usedfor commercial or rental purposes, this warranty applies for only 90 days from date _ of purchase.
KNOW Your new BRUSHWACKERT.M. has been however, even with the best of preventative check out procedures listed below: YOUR carefully BRUSHWACKERTM packed measures, at the factory damage Remove all items from the carton, lay them out and check assembly. Also check carefully for any visible damage. (IN THE OR BOTH, NOTIFY YOUR SEARS STORE IMMEDIATELY.) You should the unit. familiarize Refer yourself to drawing with the various parts of to prevent does sometimes your occur.
ASSEMBLY 1. 5. INSTRUCTIONS After checking parts, fasten fuel tank and fit drive shaft to engine with four screws. Figure 1. GROUND WIRE OF TOGGLE SPLASH DEFLECTOR ASSEMBLY Attach the splash deflector unit to the Drive Shaft Housing using the clamp and screws provided. See figure 4. SWITCH / STAND Figure 4 Figure 1 You are now Lock on the 6. . 3. Attach stand to engine with two bolts. Figure 1. Clamp the handle bar to the drive Connect the toggle switch cord from the ignition coil. Figure 2.
Assembly Instructions [€ont'd.| CAUTION: When preparing for the job been stored stored fuel you mixture, longer longer than than performance. time it should CAUTION! mix only the amount needed are to do. Do not use fuel mixture two this will (2) months. cause hard NEVER fill the fuel tank Fuel starting If fuel mix has been stored be removed and filled with that has mixture and poor longer than this a fresh mixture. to the inlet port level.
Engine 4. Starting Procedure {cont'd} Stopping Set the throttle lever at starting position ing button of throttle lever. Figure 9. with the lock- the Engine 1. Reduce the engine 2. Set the toggle switch 3. After stopping FUEL rpm to idle. at "OFF". the engine, COCK ...shutting tank to the engine. Figure 7. IMMEDIATELY off Figure CLOSE the fuel supply THE from the 7.
Tips for Long Drain Storage all spark fuel from plug, the fuel tank pour a teaspoon Rotate the crankshaft handle slowly. of oil through several Replace and carburetor. times and the machine the plug hole. by pulling the spark Emergency measure during operation In case of emergency, pull the detaching Remove will be detached from belt upward strongly the body. the starter plug and proceed with storage.
NYL ON LINE HOW The TO USE Line work. Trimmer depends cutting. bricks, the for upon LINE is designed It uses only specially-treated THE wear. type trimming and light tip of a monofilament longer the of The life surface of the against edging nylon cutting which 17. line line you fences. The shrubs and could cutting around line scar fences.
Engine Operation Always 3. release (cont'd.} the trigger and allow the engine to return to idle speed whe'n not cutting. 4 The carburetor and not carburetor section 5. has been carefully should To stop any adjustment, in this position. require see adjusted further at the factory adjustment. ENGINE For ADJUSTMENTS manual. engine, move Figure the toggle switch to the "OFF" 7. Proper length of cutting eyelet to end of line. Figure MOWING a.
D° SCALPING To remove all unwanted vegetation around trees, posts, monuments, etc., maintain a 30 degree angle with the nylon cutting head and allow the tip of the cutting line to strike the ground. Figure 19. NOTE: Increased line wear is to be expected when using the edging or scalping techniques. Figure 21 C. Figure E. THE SPOOL When it becomes spool, the following 1.
Line & Spool Maintenance GENERAL [€ont'd] A. MAINTENANCE LUBRICATION FOLLOW INSTRUCTIONS! After every 10 hours of operation, remove the plug and fill gear box with grease, Figure 24 4, There are two eyelets, one on each side. After the nylon cord has been threaded through eyelets with thick side facing shaft holt, (may not be applicable on all heads), insest eyelets in side slots of housing while inserting interspool. Thus snapping together both interspool and eyelets in housing with one motion.
\ t_o it" o_ sD ILl C_ O 0.
.J z _ _ _ 8 I-- _ .... C _ __-=a _-_ S _J _J _3 0 , ..
\ \. \ i \ o., 0 -p IX I,M _ZJ 14.
o 0 ' ' ' T o uJ 0 0 <_: _ _ .:-__oSozzzzzzoooooo , , , ooo_ oSo o 0 :E I--I _r_ I- = e') t,., 2 I-: n_ w "I- 8_ z 0 l- nn €/) nO €/) ill .... _ _ .a _ ._ ._ c).
\ \ \ \ uf) r_ / _D ..I ILl Q 0 i l-.J <_ Q.
.! o A 0 2 O3 O3 ,.=, "6 t_ fa m" _ v _k z_ o o Uil i. -T_q cx t-n .F..--. r,_ a_ _= , - _ U.
q_ u'J qt a_ _D .,J w r_ 0 i €_ ml cr_ o..
1% r,,, rjD .J IJJ 0 X X"_ _r , 2 < t-- 0 Q,. ,o ,- = E 8 _ _ = o -_ (O 2 s (.0 -r P u') p ._ ._ .=_ rn (,0 _ mm_" rr 0 I.Ll m_Q< _- • .
The Model Number will be found on the top of recoil starter. Always mention the Model Number when requesting service or repair parts for your unit. All parts listed herein may be ordered from any SEARS, ROEBUCK AND CO. OR SIMPSONS-SEARS LIMITED retail or catalog store. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE FOLLOWING INFORMATION AS SHOWN IN THIS LIST. 1. The PART NUMBER 3. The PART DESCRIPTION 2. The MODEL NUMBER of the BRUSHWACKERT.M. 636. 795454 4. The NAME OF ITEM37.7cc Gas BRUSHWACKER T.M.
