OPERATOR'S MANUAL CRAFTSMAN BACK WALL WITH METAL PEGBOARD CAUTION: Back wall MUST be attached to the Workbench before the top is attached. CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Distributed by Sears Brands Management Corporation.
LEIS SAFETY WARNINGS AND CAUTIONS: Use appropriate safety equipment when using power and hand tools. Failure to do so may cause personal injury or product damage Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injury or product damage. DO NOT stand on this product. You may fall which may cause personal injury. DO NOT mount this product on a truck bed or any other moving object. This may cause personal injury or product damage.
“\ WARNING: Back wall with Metal Pegboard is only to be attached to one of the following Workbenches: 14929. 14528, 149256 and 14840. TOP REMOVAL: Remove and reuse fasteners from wood top. + Remove top from workbench base. STEP 1: » Remove and reuse the top and bottom fasteners from the top back of the workbench, Attach (2) A to workbench, as shown, using existing hardware and {8) CC. + Finger tighten.
HH{1) sonny KK(2) 32) Assemble (2) LL and {2) JJ loosely together. Place hardware assembly into top slots in light housing F. Tighten so each JJ locks LL into place. Attach light assembly into B and secure with {2) KK. On the 8 Workbench insert {1) HH inch hole of B to protect fight cord. int used on workbench) HH {mmm DDG) i EEK) RR(2) + Attach light assembly B to Callback! using and (8) EE as shown. Back of workbench + Use {2) RR where appropriate to support the light wire.
STEP 6: FE(6) NOTE: To reattach the top, new pilot holes may need to be marked and drilled. + Place top on the bench in the desired location. + Mark centers of mounting holes to be drilled. {if needed) « Drill 1/8" pilot holes in top. (If needed) + Reattach top using existing hardware. + Wrench tighten all fasteners. Reattach top hardware. Back Front « Drill 1/8" pilot holes in top using holes template. + Drill 1/8" pilot holes in top using holes template. + Attach using (8) FF.
Periodically the surfaces should be cleaned with a mild detergent and water. = Auto wax will preserve the unit's luster finish. Apply the wax as to a car. The wax will also help protect the unit against scratches. + Grease and oil can be removed with most standard cleaning fluids. For safety, use a nonflammable cleaning fluid. « Install grommets (4) HH in holes in E.
MANUAL DE USUARIO CRASCITARAN MONTAJE EN PARED CON TABLERO METÁLICO PRECAUCIÓN: La parte posterior DEBE fijarse al banco de trabajo antes de unir la parte superior. ATENCIÓN: Lea y siga todas las Normas de Seguridad y las Instrucciones de Funcionamiento antes de utilizar por primera vez este producto.
SEGURIDAD ADVERTENCIAS Y PRECAUCIONES DE SEGURIDAD: ™\ Utilice ef equipo de seguridad adecuado cuando emplea herramientas eléctricas. De lo contarlo, podría causarle lesiones personales u ocasionar fados al producto. Utilice el personal adecuado para ef montaje y el trasijado de esta unidad. De lo contrario podría ocasionarse lesiones personales o defiar ef producto NO se ponga de pie sobre la unidad, Podría caerse y lesionarse.
ENSAMBLAJE ADVERTENCIA: El Panel Posterior con Tablee de Metal Acaballa 14943/14944 adlo debe ser colocase en jos siguientes Bancos de Trabajo: 14929, 14928, 14925 and 14940. REMOCIÓN DE LA PARTE SUPERIOR: + Retire y vuelva a utilizar los sujetadores del tope de madera. » Retire la parte superior de |a base del banca de trabajo. PASO 1: » Quite y reutilice la tapa y los sujetadores inferiores de la tapa detrás del banco de trabajo.
442) Monte libremente junto. Ponga el montaje del harreare en ranuras superiores en la cubista ligera F. Apriete tan cada uno las cerraduras JJ LL en lugar. Ate a la asamblea ligera en B y asegúrela con Parte movible dei banco de trabajo agujero de B para proteger la cuerda ligera, light corda. {Ho titado on 6 Banco de laido) HH « Ate el montaje ligero B a Acaballa usando como se muestra Parte posterior del banco de trabajo Utilice (2) los RR en su caso para apocar el alambre ligero.
PASO 6: NOTA: Para reatar la tapa, los nuevos agujeros experimentales pueden necesitar ser marcado y ser perforado. + Coloque la parte superior del banco en el lugar de su elección. + Marque ios centros de los agujeros de montaje que deben ser taladrados. (Si esta necesitado} + Haga agujeros piloso de 1/8 guipada en ia parte superior. (31 esta necesitad) « Vuelva a colocar la parte superior utilizando el harreare existente + Apriete con lave todos los sujetadores.
4 \ MANTENIMIENTO « Periódicamente las superficies deberán implarse con un detergente suave y agua + La cera para automóviles preservar ef acabado brioso de la unidad. Aplegue la cera como lo garfa al carro. La cera también ayudar a proteger la unidad contra raspones. + La grasa y el aceite pueden retirarse con la mayoría de ios líquidos estándar para limpieza. Por razones de seguridad, utilice un liquide incombustible para limpieza. « Instale los ojales {4) HH en agujeros en E.