- i n,,lU,,,i ,,iru,,_l MODEL NO. 757.242330 ® 10qNCH MOLDBOARD PLOW FOUR 55 POUND WHEEL WEIGHTS, ONE FRONT WEIGHT BRACKET, AND A SLEEVE HITCH ACCESSORY ARE REQUIRED FOR OPERATION ALSO, TIRE CHAINS ARE RECOMMENDED Caution: Read Rules for Safe Operation and Instructions Carefully ® Assembly ® Installation ® Operation ® Repair Parts ,,it, i ,n .............. inlll,l,l,,, L-1222 SC Sears, Roebuck And Co, ilU,i i,i ,,,lit i lU................... '11' 1: ilU,irll nl, .....................
LIMITED ONE YEAR WARRANTY ON MOLDBOARD PLOW For 1 year from the date of purchase, when this Moldboard Plow is maintained and lubricated according to the operating and maintenance instructions in the owner's manual, Sears will repair, free of charge, any defect in material or workmanship..
CONGRATULATIONS on your purchase of a Sears Craftsman 10" Moldboard Plow It has been designed, engineered, and manufactured to give you the best possible dependability and performance Should you experience any problem you can not easily remedy, please contact your nearest Sears Service Center/Department We have competent, well trained technicians and the proper tools to service or repair your PLOW Please read and retain this manual The instructions will enable you to assemble and maintain your Plow properly
@ Nu Z-1216-A HARDWARE BAG 1 Bo]674P Hex ILocM Nut 5/16 3 Used No 26 P-597 Spacer 5/8t D x 1/2 2 Used No 35 No 3 B-1678F _ Hex (Lock) Nut No 29 5/8 No 2 Used 28 Hex 1M1624P Hex Head t12 x 1-1/2' 1M1628P Head Plow Bo_t 1t2 1/2' x 1_3/4" 2 Used Boft 15Mt632P Bolt x 2' 1 Used 2 Used No 2 Nut 5/8 No 44 45Mt717P Flat Washer Washer 5116' 3 Used Used Z-1216-B No No 42 45Mtl11P Fiat 3g 30M2000P Hex 1/2 1 Used HARDWARE No 45 45M2121P Flat Washer 2 5/8 Used BAG
Z-1216-C HARDWARE / NO 24 Coulter BAG No 6 P-172P Coulter Axle 1 Used. Clamp Used O No 23 P-386P "U" Bolt 1 Used ASSEMBLY NOTES o IT IS RECOMMENDED THAT YOU CAREFULLY READ THIS OWNER'S MANUAL BEFORE STARTING ASSEMBLY OF THE UNIT Tools Required For Assembly: 1-10" Adjustable Wrench 1- 15/16" Wrench 1_ 13/t6" Wrench 1- 3/4" Wrench 1-Pair of pliers 1- t/2" Wrench 1-9/16" Wrench 1 - Pair Gloves g Before starting assembly, arrange each kind of hardware into a group to ease assembly g Right hand (RH.
PLOW BOTTOM AND STANDARD Referto Fig.2 @Assemblethe landsideto frog usingtwo 3/8"x 1" plow boltsand 3/8" hex nuts. @ Attachstandardto frog using 1/2"x2" plow bolt and 1/2" hex nut as shown, © Insertthe 1/2"x 1_1/2"carriagebott throughfrog andstandardandsecurewith a 1/2" hex nut. @ Insertone1/2"x I-1/2" HexBott(Tracking AdjustingBolt)throughthe "tab"atthe bottom of standard.
OPERATION PREADJUSTMENT [Refer to Fig.
PLOWING e Highweedsor grassmustbe cut downwith a rotarymowerbeforeplowing, e NEVER plow whensoil is wet+A ruleof thumb is to pick up a handfulof soil androll it into a "ball" If soil doesnot crumble,it is too wet,,tf the soilis too dry, it maybe difficult for the plow to penetrateproperly e Avoidlow areas,old roadways,paths,andother placeswhere soil is overly packed TIPS Lay out your field to be plowed, and if possible make it rectangular in shape Note: It is easier to plow a few long furrows than many sh
DEPTH ADJUSTMENT Referto Fig 8 eTo turnthe plowshareinto the groundto openthe "first"furrow,adjustthe pointdownward untilthe plowis cutting4"to5" deep e Aftera few furrows,(or desireddepthis reached)turn thecrankCOUNTER-CLOCKWISE to maintainthatdepth Do not allowlandsideto ride morethan !/2" off bottomof furrowas this will causeexcessive wearon bottomof shareresulting in poorsoifpenetration andlossof landside support Depth TURN CLOCKWISE Crank 'TO INCREASE PLOW DEPTH FIG, J4URN COUNTER-CLOCKWISE TO
TROUBLE [PLOWING PROBLEM SHOOTING DIFFICULTIES CAUSE/CONDITION AND REtVIEDIESI i REMEDY L SLOW GROUND ENTRY ® Improper Crank Adjustment. Refer to Depth Adjustment and turn crank CLOCKWISE t or 2 turns at a time. e Badly worn Plow Share. Replace with a new Share. e Ground extremely dryand hard due to lack of moisture. Add extra weight to tractor or wait until soil conditions are suitable.
MOLDBOARD PLOW MODEL NUMBER 757.242330 11 PRinTEDiN U S A 2 27 25 7 29 \ 44 \ 13 24 32 38 21 I 22 38 37 34 45 47 PARTS LiST t 18 t5 Ref_ Re|° Qty,, Qty,, No, Part No Description Hex Lock Nut, 5/16" Hex Lock Nut, t/2" Hex Lock Nut, 5/8" Model No Decal Grease fitting, 5/16" Coulter Axle Spacer, 1/2" I,D x 9/16", Cou|ter Hub Standard Beam Half Threaded Tube Hitch Bracket (Yoke) Crank 3 3 2 1 1 1 1 1 1 2 1 I 1 24 25 26 27 28 29 30 31 32 33 34 35 36 Coulter Clamp 1-- Spacer, 5/
