Owner`s manual

PLOW BOTTOM AND STANDARD
Referto Fig.2
@Assemblethe landsideto frog usingtwo 3/8"x 1"
plow boltsand 3/8" hexnuts.
@Attachstandardto frog using1/2"x2" plowbolt
and 1/2" hexnut as shown,
© Insertthe 1/2"x 1_1/2"carriagebott throughfrog
andstandardandsecurewith a 1/2" hexnut.
@Insertone1/2"x I-1/2" HexBott(Tracking
AdjustingBolt)throughthe "tab"atthe bottom
of standard.Placethe 1/2" Squarenut between
the 'q'ab"andFrog,andthreadtheTracking
AdjustingBolt intothe squarenut untiltight,
Tightenall fastenerssecurely.
PLOW FRAME AND BOTTOM (Refer to Fig 3]
e Straddle the beams over standard and fasten together
at the LOWER hole in the standard with one 1/2"x 1-3/4"
bolt and 1/2" hex lock nut
e Attach end of threaded tube to side of standard at
the UPPER hole with a 1/2"x 1-1/2" hex bolt followed by
the 1/2" flat washer, then place the 9/16"spacer in the
hole in standard and secure this assembly with one 1/2"
hex lock nut
e Tighten these fasteners so that the threaded tube is
free to pivot
COULTER BLADE (Refer to Fig 4]
e Insert coulter standard into fork, align the holes and
drive the 5/t6"x 1-1/4" pin through, leaving an equal
amount of pin on each side
e Attach the coulter hub to the coulter blade using
three 5/16"x 3/4" carria£;e bolts, 5/16" flat washers, and
5/16" lock nuts
e Install the coulter blade on the fork by inserting
the axle through one leg of the fork, the coulter
hub, and other leg of fork, Secure with the two 5/8" flat
washers and 1/8"x 1-1/4" cotter pin, bend the legs over°
e Attach the coulter assembly to the plow beam as
shown, using the "U" bolt, coulter clamp, two spacers
(locate BETWEEN the plow beams), and secure with two
5/8" hex nuts
Q Position the coulter standard between the "U" bolt and
coulter clamp and move up to the highest position
eRefer to the coulter adjustment section for proper set-
ting, to be adjusted AFTER you begin plowing,
_ WARNING
O The "Attachment Clutch" Switch on dash of Tractor
(device that engages Tractor Mower) needs to be
ENGAGED at afl times while operating Tractor This
actuates the Operators Sensing Device in the Tractor
seat ---Tractor Engine wil! stop in case you dismount
or fall off Tractor Failure to actuate this device
can cause personae injury or damage to your Tractor
and Property if you were to fatl off, SWITCH MUST BE
DISENGAGED IN ORDER TO RESTART ENGINE!
1/2" x 2" Ptow bott
1/2"X1-1/2"
Carriage bolt Standard
Landside
/
1/2" Square nut
1/2"× 1-1
He× bolt- !/2"Hex nut
(Tracking Ad
3/8" Hex nuts
FIG 2
Threaded tube
Standard ___.. Crank
1/2"1D x9/16 Spacer
l/2' .I_-_,. 1/2- Lock nut
Fiat washer
t
1/2"x 1-t/2'
Hex Bolt
tube
1/2" Lock nut
1/2" x 1-3/4"
Hex Bolt Lower hole in standard
FIG. 3
5/8"1D × 1/2" Spacers _'l "U" Bolt
Ptew Beam _'_'_- ""_©
5/16"X3/4" Carriage bott
-Coutter
clamp
5/16" Locknut
Cotter pin
i
Coulter standard
I /8 5/t6 x t-1/4" Pin
Flat wa,sher Coulter fork
_-_ Coulter blade
FIG. 4