Owner`s manual

OPERATION
PREADJUSTMENT [Refer to Fig. 5 and 6]
Note: During normal plowing, the right side Tractor Wheels
will be riding in the previously plowed furrow A furrow
is the cut area your plow makes when turning the soil,
An initial setting for your plow is required to cut the
first furrow on level ground The following pre-sets will
result in an approximate 5" to 6" plowing depth,,
Remove Stabilizer Bolts and Nuts from Sleeve Hitch
The plow must be free to move side to side on Hitch
Lower your Tractor Lift Handle and lock in Lowered
Position. You may need to Lower the "Attachment Depth
Control" on your Tractor to do this
e Mount the Plow to the Sleeve Hitch with the Hitch Pin
furnished with the Hitch Refer to Figure 1 and Table 1 to
select the proper mounting hole
e Adiust Lift Spring Tension on Hitch as required, see
Hitch Manual for instructions
e Adjust the Depth Crank of Plow until Point of
Plow Share is on the ground and the rear of Plow
Landside is approximately 1" off the ground. (Refer
to Figure 5)
Note: The Plow will appear to be angled to left,
This will allow the Plow to run level when the
Right Hand Tractor Wheels are in the plowed furrow°
eThe plowing depth is set by adjusting the
Tractor Sleeve Hitch Turnbuckle until Hitch Drawstrap
has about I" of slot exposed between Pin and end
of Slot. Loosen the Hex Nut on the Hitch
Turnbuckle to adjust it Make sureto retighten it
after adjusting
eAdjust the Plow Coulter to its highest position,
e Go and make your first two furrows as described
in the diagram (X to A and turn B to C )., Make
sure the Tractor Lift Handle is Lowered and Locked
into the down position. Plow in Third Gear and near
Full Throttle Raise the Plow to the Transport
Position when turning
e If your Plow is not plowing at 4"to 5" deep
on your initial two passes, readjust the Plow Depth
Crank by turning it clockwise (.,-e.) to go deeper
or counter-clockwise (.e_) to go shallower. (See
Fig 8) Make this adjustment ONE TURN at a time
until desired depth is obtained,
Note: The rest of the furrows will be made with
the Tractor Tires in the previously cut furrows;
therefore, the Pitch (Depth) of the Plow must be
readjusted to a 5" to 6" plowing depth,
Position your Tractor with the inside of the
Right (Side) wheels against the side of the
previously plowed furrow
Start plowing for a short distance and check the
depth of the furrow Adjust the Depth Crank Clock-
wise or Counter-Clockwise ONE turn at a time and
retry until the 5" to 6" depth is obtained
FIG,. 6
e After plowing depth is set with plow in furrow,
stop the Tractor and measure the distance from the
centerline of the Plow Coulter Axle Bolt---it
should be about 2"above the ground If it is not,
raise the Plow out of the ground and adjust the
Coulter up or down to obtain this dimension Be
sure to adjust side motion at thistime (See
Coulter Adjustment page 8)
TRACKING ADJUSTMENT (OPTIONAL)
Note: If the Plow appears to track to the left Standard and turning the Tracking Adjustment Bolt
while plowing, an adjustment is available to correct Clockwise ("_') two turns,, Retighten Hex Nuts
this condition (Refer to Figure 9) securely, Repeat Adjustment as necessary until plow
®The Tracking Adjustment is made by loosening both pulls straight at !0" from the adjacent plowed
.].[2" Hex .Nuts spcuring the Plow Bottom to the 7 swath