2723303 Owner's Manual Serial No. NOTE: Model and serial numbers may be found on the name plate located on the tool. You should record both numbers and retain them in a safe place. 1 E185030 CAUTION: Before using this Nailer, read this manual and follow all its Safety Rules and Operating Instructions. Sears, Roebuck and Co.
TABLE OF CONTENTS SECTION PAGE Warranty................................................................................................. 2 Product Specifications........................................................................ 2 Safety Instructions................................................................................ 3 Accessories and Attachments............................................................. 6 Know Your Brad Nailer..............................................................
SAFETY 6. DONT FORCE THE TOOL It will do GENERAL SAFETY INSTRUCTIONS the job better and safer if used at the rate for which it was designed. A WARNING Do not attempt to operate this tool until you have read and thoroughly understand all instructions, safety rules, etc., contained in this manual. Failure to comply can result in accidents involving fire, electric shock, or serious personal injury.
13. DtSC0NNECTT00L when not in 17. use, before servicing and when ioading or changing accessories. REPLACEMENT PARTS, When servicing, use only identical replacement parts ordered from a Sears service facility. 14. AVOID UNINTENTIONAL STARTING. Never carry tool with 18. WEAR HEARING PROTECTION during extended periods of operation. your finger on the switch. 15.STAY ALERT. Watch what you are doing and use common sense.
SPECtFIC SAFETY INSTRUCTIONS 10.OUR1NG OPERATION, the nailer may feel warm to the touch. This is FOR THIS NAILER normal. However, if the nailer starts to feel hot, discontinue use until the unit cools down. A WARNING DO NOT AIM NAILER OR SHOOT NAILS AT A PERSON OR ANIMAL. Released nails can cause severe injuries. GROUNDING INSTRUCTIONS 1. USE ONLY THE NAILS INDICATEDIN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides in this manual.
Figure B 3-Prong Plug Grounding Lug Make Sure This is Connected to a Known Ground Grounding Prong 2-Prong Receptacle Properfy Grounded 3-Prong Outlet Adapter FIGURE (A) Shows a 3-wire electrical plug and outlet that has a grounding conductor. If a properly grounded outlet is not available, an adapter (FIGURE B) can be used to temporarily connect this plug to a 2-contact ungrounded outlet.
KNOW YOUR BRAD NAILER OPERATION HOWTO LOAD YOUR BRAD NAILER (FIGURE 1) 1. Unplug nailer from power source. 2. Use only brad nails recommended; see brad nail chart. 3. Push up the latch (1) toward the magazine and slide out the magazine (2). 4. Position the nailer exposing the magazine chamber (3). 5. Load nails into the magazine, nail points facing down toward the bottom of the nailer. 6. When loading different lengths, do not load nail heads into the upper part of the slot.
TO NAIL (FIGURE 2) AWARNING AWARNING Do not allow familiarity of your nailer to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. Always wear safety goggles or safety glasses with side shields when operating your nailer. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. Fig. 2 1. Plug nailer into 120 Volt, 60Hz power outlet, 2.
7. Replace all parts in reverse order. 8. Tighten screws. 9. Make sure that the safety lock pin is correctly sticking out of the tacking mouth assembly. CLEARING A JAMMED NAIL (FIGURE 3) 1. Unplug the cord and remove all brads from the magazine. 2. Remove the two screws and Fig.3 washers (1) located on the tacking mouth cover, 3. Remove the cover (2). CAUTION: Be careful, the safety lock pin and spring may shoot forward. 4. Remove safety lock pin (3) and spring (4).
ELECTRIC BRAD NAILER MODEL NUMBER 836.
siavd
13 ICMFnHHirj, (U«mcMullen ==_^, 11 ^=Ь=щ^^ 14
For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7 days a week 1-800-4-REPAIR (1-800-473-7247) For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Cal! 9 am - 5 pm, Monday-Saturday 1-800-82