Owner's Manual Model No. 875.199800 3/8-in. Butterfly impact Wrench Unpacking When unpacking inspect occurred loose before this for any damage during fittings, putting transit. bolts, this product, carefully that may have Make sure any etc. are tightened product into service. WARNING: Please read and save these safety and operating instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Owner's Manual Model No. 875.199800 Owner's Manual Model No. 875.
Owner's Manual Disconnect Model No. 875.199800 the air tool from air supply and during non-operation. Do not wear loose fitting clothing, Manual Some materials before changing tools or attachments, servicing Owner's tar, contain Use attachments designed for use with air powered tool. Always examine could accessories prolonged before mounting for chips, such as adhesives chemicals cause serious Model whose injury exposure. and vapors with Always No. 875.
Owner's Manual Model No. 875.199800 Owner's Manual be a flexible Air Tool Hook Up movement Model No. 875.199800 hose in order to isolate of the compressor. This tool features a regulator valve. Rotate Route the initial take-off line (pipe) as regulator straight The setting (H) and (L) on the regulator up the shop wall and as high as possible. This will help minimize water leaving the compressor traveling and through system until desired output is achieved.
Owner's Manual Model No. 875.199800 1. Disconnect the impact wrench from the air supply. An in-line filter-regulator-lubricator (fig 1) is recommended as it increases tool life and keeps the tool in sustained operation. The in-line lubricator should be regularly checked and filled with air tool oil. Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to the tools exhaust ports and holding the throttle open approximately 30 seconds.
Owner's Tool runs slow or will Manual 1. Grit or gum in tool not operate. Model No. 875.199800 1. Flush the tool with air tool oil, gum solvent, or an equal mixture of SAE 10 motor oil and kerosene. Lubricate the tool after cleaning. 2. No oil in tool 2. Lubricate the tool according to the lubrication instructions in this manual. 3. Low air pressure 3a. Adjust the regulator on the tool to the maximum setting (If applicable). 3b.
Manual dei Propietario Modelo No. 875.199800 Llave de impacto de mariposa de 3/8 puig Desempaquetar Despues examinelo identificar ocurrido de desempaquetar cuidadosamente el producto, para da_os que pudieron durante el transporte. Cerci6rese de apretar accesorio, perno, este producto haber cualquier etc., antes de poner en servicio. ADVERTENCIA: Lea y guarde estas instrucciones de seguridad y operaci6n.
Manual del Propietario Modelo Caracteristicas y operaci6n Especificaciones Garantia del producto Requisitos del compresor Instrucciones de seguridad importantes Instalaci6n y operaci6n Mantenimiento Piano de vista despiezada y lista de piezas Localizaci6n y soluci6n de fallas La Ilave de impacto de mariposa con mando cuadrado de 3/8 pulg Craftsman, Modelo 875.199800, es ideal para usar en el ensamble general, asi como en aplicaciones de autom6viles, agricultura e industriales.
Manual del Propietario Desconecte la herramienta del suministro de aire antes de cambiar herramientas o accesorios, darte servicio o durante el tiempo que no este funcionando. No use ropa suelta, bufandas o corbatas en el area de trabajo. La ropa sueIta podria quedar atrapada en las piezas en movimiento y resultar en una Iesi6n personal grave. No use joyas mientras usa la herramienta. Las joyas podrian quedar atrapadas en Ias piezas en movimiento y resultar en una Iesi6n personal grave.
Manual del Propietario Cone×i6n Modelo de la manguera Linea principal = Dia. int. min. tnclinado hacia abajo y Linea Dia. Lubricador Regulador 1 = 1/2 pulg Linea de admision Filtro de drenaje Valvula de ! drenaje Valvula Manguera de aislamiento de drenaje Figura 1 Conexion de la manguera de aire correcto y que esten bien conectados antes de usar Ia herramienta neumatica.
Manual del Propietario Modelo 1. No. 875.199800 Desconecte la Ilave de impacto del suministro de aire. Manual del Propietario Piano Modelo No. 875.199800 de vista despiezada 7 2. Quite el tornillo ranurado o de cabezal Allen Lubricacibn Se recomienda usar un filtro-reguladorlubricador en linea (Fig.l) ya que incrementa la duraci6n de la herramienta y mantiene la herramienta en una operaci6n sostenida. Debera comprobar el lubricador en linea con regularidad y Ilenarlo con aceite para 4.
Manual del Propietario La herramienta funciona lentamente o no funciona. Modelo 1. Irrigue la herramienta con aceite para herramientas neumaticas, diluyente de resinas, o una mezcla de igual proproci6n de aceite de motor SAE 10 y queroseno. Lubrique la herramienta despues de la limpieza. 1. En la herramienta hay polvo, arena o resina. 2. En la herramienta aceite, no hay 3. La presi6n del aire esta baja. 4. Fugas de la manguera aire 5. Caidas de presi6n. No. 875.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME ® (1-800-469-4663) Call anytime, day or night (U.S.A. and Canada) www.sears,com www.sears.