® MODEL NUMBER 917.250551 OWNER'SMANUAL o Assembly o Operation o Customer Responsibilities o Service and Adjustments o Repair Parts CAUTION: Read and follow all safety rules and instructions before operating this equipment.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE iS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH I. • • • • • • II. GENERAL OPERATION III. CHILDREN Read, understand, and fellow all instructions in the manual and on the machine before starting Only allow responsible adults, who are familiar with the instructions, to operate the machine.
PRODUCT CONGRATULATIONS on your purchase of a Sears Tractor It has been designed, engineered and manufactured to give you the best possible dependability and pefformance_ Should you experience any problem you cannot easily remedy, please contact your nearest Sears Authorized Service CentedDepartmenL We have competent, welltrained technicians and the proper tools to service or repair this tractor. Please read and retain this manual.
TABLE OF CONTENTS SAFETY RULES ............................................................ 2 PRODUCT SPECIFICATIONS ...................................... 3 CUSTOMER RESPONSIBILITIES ..................... 3, 15-18 WARRANTY .................................................................. 3 TRACTOR ACCESSORIES .......................................... 5 ASSEMBLY ............................................................. 7-10 OPERATION ..........................................................
ACCE$SORmES ANDATTACH ENTS These accessories and attachments were available through most Sears retail outlets and service centers when the tractor was purchased Most Sears stores can order these items for you when you provide the model number of your tractor ENGINE SPARK PLUG MAINTENANCE GAS CAN ENGINE OtL FUEL STABILIZER AIR FILTER BLADES BELTS PERFORMANCE Sears offers a wide variety of attachments that fit your tractor you This list was current at the time of publication; however, may be made in
CONTENTS OF HARDWARE PACK Parts Bag contents shown full size Parts packed separately (1) Shoulder Bolt 5/16-18 in carton Seat (1) Knob (2) Gauge Wheel Bars (1) Washer Steering Wheel 17/32 x 1-3/16 x 12 Gauge t I I Springs (double loop) I I I I I I I Owner's Manual Parts Bag ]er Springs (single loop) Parts bag contents not shown full size (2) Washers 3/8 x 7/8 x 14 Gauge (2) Shoulder Bolts Wheels _(2) Centerlock Nuts "_ Steering Wheel Insert ® (2) Hex Bolts 1/4-20 x 3/4 Front Link
ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely Use the correct tools as necessary to insure proper tightness TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed.
BLY CONNECT BATTERY & (See Fig. 2) INSTALL CAUTION: Do not short battery terminals. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. Lift hood to raised position • Open terminal access doors, remove terminal protective caps and discard.
ASSEMBLY INSTALL MOWER (See Figs. 4 and AND DRIVE BELT Connect anti-sway bar to chassis bracke[ under left footrest and retain with double loop retainer spring. 7) Turn height adjustment knob clockwise slack from mower suspension, Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control.
ASSEMBLY ,/CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THEBES TPERFORMANCE AND SA TISFACTION FROM THIS QUALITY PRODUCT, PLEASE REVIEW THE FOLLOWING CHECKLIST, ¢" All assembly instructions have been completed ¢" No remaining loose parts in carton ¢" Batteryis properly prepared and charged 1 hour at 6 amps) ¢ Seat is adjusted comfortably and tightened securely.
OPERATmON KNOWYOURTRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments this manual for future reference, AMMETER Save THRO_LECONTROL ATTACHMENT CLUTCH SWITCH LIFT LEVER CHOKE SWITCH LIFT LEVER CLUTCH/BRAKE PEDAL HEIGHT ADJUSTMENT KNOB RANGE PARKING SHIFT LEVER \ BRAKE LEVER GEARSHIFT LEVER FIG.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which carl result nnsevere eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs, We recommend a wide vision safety mask over the spectacles or standard safety glasses.
OPERATION TO ADJUST • GAUGE WHEELS (See Fig. 7) TO OPERATE Adjust mower to desired cutting height Lower mower with lift control Remove rear retainer spring and clevis pin which secure each gauge wheel Replace retainer springs into clevis pins. . RETAINER • SPRING hills with slopes greater than 15° and CAUTION: not any drive slope. up or down do not drive Do across I _ Lower gauge wheels to ground_ Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pins.
OIPERAT ON IVlOWING TiPS ADD GASOLINE Fill fuel tank Use fresh, clean, regular unleaded gasoline (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life) IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER G RADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING Tire chains cannot be used when the mower housing is attached to tractor.
CUSTOMER FILL ,NDATE S RESPONSUB_LnTmES _'_°_ _._"__Z_J__I _o_ A REGOLAR BY OUC OMPLETB SERV,CE ! .,_O_ _ _..
CUSTOMER RESlPONSIB L TIES TRACTOR o Always observe safety rules when performing any rrraintenance. The blade can be sharpened with a file or on a grinding wheel Do not attempt to sharpen while on the mower o To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer) = Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground.
CUSTOMER RESPONSIB L TmES , BATTERY TO CHANGE ENGINE OIL (See Fig& 14 and 15) Your tractor has a battery charging system which is sufficient for normal use However. periodic charging of the battery with an automotive charger will extend its life.
CUSTOM CLEAN AIR SCREEN RESPONSmBMLmTHES MUFFLER (See Fig. 15) Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage, Air screen must be kept free of dirt and chaff to prevent engine damage from overheating Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.
SERWCE AN CAUTION: o o ° • o BEFORE PERFORMING ADJUSTMENTS ANY SERVICE OR ADJUSTMENTS: Depress clutch/brake pedal fully and set parking brake. Place gearshift lever in neutral (N) position. Place attachment clutch in "DISENGAGED" position. Turn ignition key "OFF" and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
SERVICE ADJUSTMENTS TO REPLACE FRONT-TO-BACK ADJUSTMENT (See Figs. 20 and 21) IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE To obtain the best cutting results, the mower housing should be adjusted so the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.
SERVICE AND ADJUSTMENTS TO REPLACE (See Fig. 23) MOWER BLADE DRIVE BELT ROTOR Park the tractor on level surface, Engage parking brake • Remove mowerdrive belt (See'q-O REPLACE MOWER DRIVE BELT" in this section of this manual). Remove mower (See "TO REMOVE MOWER" in this section of this manual), o Remove four screws from R.H, mandrel cover and remove cover, Unhook spring from bolt on mower housing o Carefully roll belt off RH mandrel pulley.
SERVICE AND ADJUSTMENTS TO REPLACE (See Fig. 26) MOTION DRIVE BELT FRONT BELT REMOVAL Engage parking brake (creates slack in belt)_ Remove mower drive belt from electric clutch pulley only (See "TO REPLACE MOWER DRIVE BELT" in this section of this manual) Roll motion drive belt off transaxle pulley. Roll belt off clutching idler pulleys, then off engine pulley and front V-idler pulley_ Pull belt out of all belt keepers BELT INSTALLATION - TO ADJUST TOEqN (See Figs.
SERVICE AND ADJUSTMENTS TO REMOVE WHEEL FOR REPAIRS FRONT WHEEL (See Fig 29) Block up axle securely. Remove axle cover, retaining ring and washers to allow wheel removal • • Repair tire and reassemble. Replace washers and snap retaining ring securely in axle groove Replace axle cover L,H. PANEL WASHERS -- BOLT RETAINING RINI AXLE COVER "-e FIG. 30 FIG. 29 REAR WHEEL o TO REPLACE HEADLIGHT BULB Raise hood • Pull bulb holder out of the hole in the backside of the grill.
SERVICE AND ADJUSTMENTS TO ADJUST (See o A'F]'ACHMENT LIFT SPRING ADJUSTMENT Fig. 31) SPRING RUSHING While holding spring bushing with wrench, loosen jam nut Turn adjustment bolt clockwise to extend spring and reduce lift effort for heavier attachments.
SERVUCE ADJUSTMENTS ENGINE TO ADJUST CHOKE CONTROL Figs. 33 and 34) TO ADJUST THROTTLE CONTROL (See CABLE The choke control has been preset at the factory and adjustment should not be necessary check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows: (See Fig. 33) The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening eable.
SERVICE AND ADJUSTMENTS TO ADJUST CARBURETOR (See ACCELERATION Fig.
STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM Will not start CAUSE POINTS CORRECTION 1 Out of fuel 2 3 4 5 6 7 Engine not "CHOKED" Engine flooded Bad spark plug Dirty air filter Dirty fuel filter Water in fuel 1 Fill fuel tank properly 2 3 4 5 6 7 See "TO START ENGINE" in Operation section Wait several minutes before attempting to start Replace spark plug.
TRO PROBLEM Engine continues to run when operator leaves seat with attachment clutch BLESHOOTRNG POmNT$ CAUSE CORRECTION 1 Faulty operator-safety presence control system 1 2 Worn, bent or loose blade Mower deck notlevef 1 2 Replace blade Tighten blade bolt Level mower deck 3 4 Buildup of grass, leaves, and trash under mower Bent blade mandrel 5 Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels 3 4 5 Clean underside of mower ho_Jsing Replace blade mandrel
TRACTOR - - MODEL NUMBER 917.250551 SCHEMATIC RED BLACK BATTERY FUSE 3O AMP RED , AMMETER WttlTE p l ("_ I BLACK i ' SOLENOID CLUTCH / BRAKE (PEDAL UP) BLACK ELECTRIC CLUTCH RED E IGNITION SWITCH STARTER J F BLACK t k --I © S r G WHITE O__ i I L _ J BLACK ) A BLACK BLACK I i D L ..... ._ SEAT SWITCH (NOT OCCUPIED) PTO (DISENGAGED) i I I I q _ I I I u .........
REPAUR PARTS TRACTOR - - MODEL NUMBER 917,25055'1 7 7 DECALS 18 6 3 15 15 8 13 4 13 10 8 \ 9 2 20 5 19 11 12 14. KEY PART NO. NO. 1 2 3 4 5 138955 146708 146705 146706 145003 6 7 8 9 10 11 12 133644 138048 142241 146709 137537 4900J 146047 WHEELS KEY PART NO, NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.
REPAIR PARTS TRACTOR -- MODEL NUMBER 917.250551 ELECTRICAL KEY NO. PART NO.
REPAIR PARTS TRACTOR CHASSIS -- MODEL NUMBER 917.
REPARR PARTS TRACTOR CHASSIS - - MODEL NUMBER 917.250551 AND ENCLOSURES KEY NO. PART NO.
BEPAIB PAR'TSBAcTOB""_O0_L"""'_ l / / 9 69 36
REPAHR PARTS TRACTOR GROUND KEY NO, - - MODEL NUMBER 917.250551 DRIVE PART NO. 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 21 22 23 24 25 26 27 9858M1 7563R 17490508 73680600 76020412 135758 12000034 140080 142509 136927 9204H 139419 138901 19131316 143012 126909X 137104 136926 23260412 633A109 106932X 136925 136923 137552 17490528 28 29 30 34 35 36 37 73350600 137213 19131614 124236X 137648 138364 121749X KEY NO.
REPAIR PARTS TRACTOR STEERING - - MODEL NUMBER 917.
REPARR PARTS TRACTOR STEERING - - MODEL NUMBER 917.250551 ASSEMBLY KEY NO. PART NO.
_IVQ/NE / a,9 / / _i_:s---s 7 43 10 a_
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.250551 ENGINE KEY NO. PART NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.250551 SEAT ASSEMBLY _---16 19 12 3 KEY NO, PART NO. 1 2 3 4 5 6 7 8 9 10 12 13 140124 140551 140675 127018X 145006 73680600 124181X 17490508 19131614 140552 121246X 121248X DESCRIPTION Seat Bracket, Pivot Seat Strap, Fender Bolt, Shoulder 5/16-18 x _62 Clip, Push In, Hinged Nut, Crownlock 3/8-16 Uric Spring, Seat Cprsn Screw, Thdrol 5/16-18 X 1/2 Washer 13/32 X 1 X 14 Ga Pan, Seat Bracket, Mounting Switch Bushing, Snap KEY NO. PART NO.
REPAIR PARTS TRACTOR - MODEL NUMBER 917.250551 LIFT ASSEMBLY 4O 42 43 34 33 31 9 1o 39 / 1 /I 3 29 4 2 6 11 23 13 12 23 22 12 13 2O 41 KEY NO. PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 121006X 145542 121002X 12000022 19292016 74780624 125631X 122365X 122364X 2876H 146704 3146R 139868 140302 73680600 674A247 73350600 143363 19131316 5328J 74760616 127218 4939M KEY NO.
REPAIR PARTS TRACTOR MOWER - - MODEL NUMBER 917.250551 DECK 55 45 48 48 48 j45 I 63 _ 62 I 47 59 60 60 58 64 1 2 36 4 36 2 22 2 3 21 6 99 54 23 44 .
REPAaR PARTS TRACTOR MOWER - - MODEL NUMBER 917.25055'1 DECK KEY NO, PART NO.
REPAIR PARTS TRACTOR - - MODEL NUMBER 917.
REPARR PARTS TRACTOR - - MODEL NUMBER 917.250551 TRANSAXLE KEY PART NO. NO.
REPAIR PARTS TRACTOR KOHLER ENGINE - MODEL - - MODEL NUMBER NUMBER 917.250551 CV22 - PS67515 CYLINDER HEAD, VALVE AND BREATHER CRANKCASE ! 26-_Q---27 _' I • 25t 2 \ I 23,,_ _ _-' I-_11 22 14 151517 20 --1_ 18 1 _23 2 24 -- 27 16 15 18 17 1312_11_: _ _- 4 6-- 7 f0 ! -26 3m © Q 42 -26 _-29 45 44 _L.
REPAIR PARTS TRACTOR KOHLER ENGINE - MODEL NUMBER - - MODEL NUMBER CV22 - PS67515 CYLINDER HEAD/VALVE/BREATHER CRANKCASE KEY PART NO. NO. KEY PART NO. NO.
REPAIR PARTS TRACTOR KOHLER ENGINE - MODEL IGNITION / ELECTRICAL NUMBER - - MODEL NUMBER 917.250551 CV22 - PS67515 BLOWER HOUSING AND BAFFLES I I _2 O' 25_ 5 10 12 20 _1.
REPAIR PARTS TRACTOR KOHLER ENGINE - MODEL NUMBER -- MODEL NUMBER 917.250551 CV22 - PS67515 IGNITION/ELECTRICAL BLOWER HOUSING & BAFFLES KEY PART NO. NO. KEY PART NO. NO.
REPAUR PARTS TRACTOR KOHLER ENGINE - MODEL NUMBER - - MODEL NUMBER 917.
REPAUR PARTS TRACTOR KOHLER ENGINE - MODEL NUMBER - - MODEL NUMBER 917.250551 CV22 - PS67515 STARTING SYSTEM KEY PART NO° NOo DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 Screw M8 x 125 x70 Screw M8 x 1_25 x 80 Cover, Pinion Starter Assembly (Includes 6-11) Washer (3) Kit, Drive End Cap, Drive End Armature Kit, Brush and Spring Cap, Commutator End Bolt, Thru(2) M-0839070 M_0839080 24 096 05 25 098 03 12 468 01 12 755 54 12 227 06 45 170 03 82 755 28 12 22711 1208625 OIL PAN/LUBRICATION KEY PART NO. NO.
REPAnR PARTS TRACTOR KOHLER ENGINE - MODEL NUMBER - - MODEL NUMBER 917.250551 CV22 - PS67515 CRANKSHAFT ,,,..
REPAIR PARTS TRACTOR KOHLER ENGINE - MODEL NUMBER - - MODEL NUMBER CV22 - PS67515 FUEL SYSTEM KEY PART NO. NO. 1 24 853 25 2 3 24 041 15 24 053 25 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 NOT ----- 917.250551 CRANKSHAFT KEY PART NO. NO.
SERVICE NOTES 56
SERVICE NOTES 57
RVICE NOTES 58
iI Z I I d > LIJ 59
® SEARS OWNER'S MANUAL 22.5 HP TWIN CYLINDER ELECTRIC START 50" MOWER 6 SPEED TRANSAXLE GARDEN TRACTOR MODEL NO. 917.250551 Each tractor has its own model number_ Each engine has its own model number. The model number for your tractor will be found on the model plate located under the seat. The model number for your engine will be found on the blower housing of the engine. All parts listed herein may be ordered from any Sears, Roebuck and Co. Service Center/Department and most Retail Stores.
