Owner's Manual £RI:IFTZMAN 20.0HP ELECTRIC START 50" MOWER AUTOMATIC GARDEN TRACTOR Model No. 917.273061 • Safety • Assembly • Operation • Maintenance • Repair Parts CAUTION: Read and follow all Safety Rules and Instructions before about this product, operating this equipment. Sears Craftsman Help Line 5 am - 5 pro, Mon- Sat For answers to your questions 1-800-659-5917 Sears, Roebuck and Co., Hoffman Estates, II 60179 Visit our Craftsman Call: website:www.sears.
Warranty............................................... 2 SafetyRules.......................................... 2 ProductSpecifications..........................5 Assembly............................................... 8 Operation............................................ 12 MaintenanceSchedule......................19 Maintenance....................................... 19 Serviceand Adjustments....................23 Storage............................................... 31 Troubleshooting.................
• • • • • Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. Turn off blades when not mowing. Stop engine before removing grass catcher or unclogging chute. Mow only in daylight or good artificial light. Do not operate the machine while under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways. • Use extra care when loading or unloading the machine into a trailer or truck.
• Never run a machine inside a closed area. • Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing. Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. Never make adjustments or repairs with the engine running.
PRODUCT MAINTENANCE SPECIFICATIONS GASOLINE CAPACITY ANDTYPE: 3.5 GALLONS UNLEADED REGULAR OIL-I-YPE SAE 10W-30 API-SF/SG/SH): A Sears Maintenance Agreement is available on this product. Contact your nearest Sears store for details. CUSTOMER 32°F) OILCAPACITY: W/FILTER: 4.2PINTS W/O FILTER:3.TPINTS SPARK PLUG: GAP: .030") Champion VALVE CLEARANCE: NON-ADJUSTABLE GROUND SPEED RC12YC FORWARD: 5.8 (MPH): REVERSE: 2.
Parts Bag contents shown full size (1)ShoulderBolt 5/16-18 (1) Knob _ Washer 17/32 x 1-3/16 x 12 Gauge (3) Retainer J (4) Retainer Springs (single loop) 6 Springs (double loop)
Parts packed separately in carton Parts Bag contents not shown full size F_ 2) Shoulder Bolts (2) Washers L.
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin. TOOLS REQUIRED _1 FOR ASSEMBLY .J"'_ Steering _.-_" Wheel Insert A socket wrench set will make assembly easier. Standard wrench sizes you need are listed below.
INSTALL SEAT TO DRIVE Adjust seat before tightening knob. adjustment • Remove cardboard packing on seat pan. • Place seat on seat pan and assemble shoulder bolt. Tighten shoulder bolt securely. • Assemble adjustment knob and flat washer loosely. Do not tighten. • Lower seat into operating position and sit on seat. • Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. • Get off seat without moving its adjusted position.
INSTALL MOWER AND DRIVE BELT Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control (see Know Your Tractor in Operation section). Engage parking brake. • Cut and remove ties securing antisway bar and belts. Swing anti-sway bar to left side of mower deck. • Slide mower under tractor with discharge guard to right side of tractor. IMPORTANT: Check belt for proper routing in all mower pulley grooves. Install belt into electric clutch pulley groove.
_CHECKUST Before you operate and enjoy your new tractor, we wish to assure that you receive the best performance and satisfaction from this quality product. Please review the following checklist: ,/ All assembly instructions have been completed. ,/No remaining loose parts in carton. ,/Battery is properly prepared and charged. (Minimum 1 hour at 6 arnps). ,/Seat is adjusted comfortably and tightened securely. /" All tires are properly inflated.
These symbols may appear on your tractor Learn and understand their meaning. or in literature supplied with the product.
KNOW YOUR TRACTOR READ THIS OWNER'S YOUR TRACTOR MANUAL AND SAFETY RULES BEFORE OPERATING Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments, Save this manual for future reference, Ammeter Ignition Switch Attachment Clutch Switch Plunger Throttle Control, Clutch/Brake Pedal Attachment Lift Lever Choke Control Ig Brake Lever Height Adjustment Knob Motion Control Lever Free Wheel Our tractors AI-rACHMENT conform to the
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOWTO USEYOUR TO SET PARKING TRACTOR • Never use choke to stop engine. IMPORTANT: Leaving the ignition switch in any position other than "OFF" will cause the battery to be discharged, (dead).
• Turn • Select desired height of cut. • Lower mower with attachment lift control. • Start mower blades by engaging attachment clutch control. • TO STOP MOWER BLADES - disen- knob counterclockwise (_) to lower cutting height. The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.
• Do not push or tow tractor at more than two (2) MPH. • To reengage transmission, reverse above procedure. NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.). TOWING CARTS AND OTHER ATrACHMENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing.
• Insert key into ignition and turn key clockwise to "START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.
• Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/ brake pedal. • Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position.
MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE Check Brake Check Tire Pressure Operation DATES _ _ _' w T Check Operator Presence and Interlock Systems I1_ R Check _ A Sharpen/Replace T for Loose Fasteners M°wer 11_7 Blades _' Lubrication Chart Batte_j I_ 0 Check g Clean Battery andCooling Terminals Check Trans_xfe Level _1_ I_' Adjust Blade Belt(s) Tension I_s Adjust Motion Drive Belt(s) Tension I##'s Check Change Engine Oil Level Engine
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. • Reassemble hex bolt, lock washer and flat washer in exact order as shown. If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES • Tighten bolt securely (27-35 Ft. Lbs.
BA'I-rERY TRANSAXLE Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
l Oil Drain Plug Air _ .------Oil CLEAN Fill Cap/ Dipstick AIR SCREEN • Reinstall the pre-cleaner (cleaned and oiled) over the paper cartridge. • Check rubber seal for damage and proper position around stud. Replace if necessary. • Reassemble air cleaner, cartridge plate, and nut. • Reinstall air cleaner cover and secure by tightening knob. Air screen must be kept free of dirt and chaff to prevent engine damage from overheating.
_kCAUTION: Before performing • • • • • • any service or adjustments: Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in "DISENGAGED" position. Turn ignition key "OFF" and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
. __ e_d°g _° omf_ _ mower t IL, _ ground _- ---- _=_,_=_;_ A'_'-_--_] SIDE-TO-SIDE j nr Bottom edge of _ mower l_-_,_l_t I to ground - ---_ Ground Line _'_-'-_- ADJUSTMENT Both Front Links Should be Equal in Length • Raise mower to its highest position. • Measure height from bottom of deck curl to ground level at front corners of mower. Distance "A" on both sides of mower should be the same. • If adjustment is necessary, make adjustment on one side of mower only.
Screws Idler Pulleys Mandrel_ Left Hand Cover Spring Electric Clutch Pulley Bolt in , Mower Left Hand Mandrel Mower Drive Belt Belt Keepers TO REPLACE BELT MOWER BLADE DRIVE • Check secondary idler arm and idler to see that they rotate freely. • Be sure spring is hooked in secondary idler arm and sway-bar bracket. Install new belt in lower groove of L.H. mandrel pulley, idler pulley, and center mandrel pulley as shown. • Roll belt over R.H. mandrel pulley.
TO ADJUST A'I-FACHMENT TO REPLACE CLUTCH The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required. Adjustments should be made by your nearest authorized service center/ department. • Make sure attachment clutch and ignition switches are in "OFF" position.
TO ADJUST LEVER MOTION FRONT CONTROL TOE-IN ADJUSTMENT Front wheel toe-in is required for proper steering operation. Toe-in was set at the factory and adjustment should not be necessary. If parts in the front axle or steering mechanism have been replaced or damaged, check toe-in and adjust if necessary. The motion control lever has been preset at the factory and adjustment should not be necessary.
REAR WHEEL • Block rear axle securely. • Remove five (5) hub bolts to allow wheel removal. • Repair tire and reassemble. Replace and tighten hub bolts securely. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.
INTERLOCKS AND RELAYS Idle Fuel Adjusting Needle -, Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from Idle speed Adjusting starting. • Check wiring. See electrical wiring diagram in the Repair Parts section. TO REPLACE FUSE Replace with 30 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. Control Cable TO REMOVE HOOD AND GRILL ASSEMBLY • Raise hood. • Unsnap headlight wire connector. • Stand in front of tractor.
ACCELERATION In general, turning the adjusting needles In (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mixture. Turning the adjusting needles out (counterclockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture. IMPORTANT: Damage to the needles and the seats in carburetor may result if screw is turned in too tight. • Move throttle control lever from slow to fast position.
ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. • Drain the fuel tank. • Start the engine and let it run until the fuel lines and carburetor are empty. • Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. • Use fresh fuel next season.
TROUBLESHOOTING PROBLEM ;HART CORRECTION CAUSE Will not start • Out of fuel. • Engine not "CHOKED" properly. • Engine flooded, • Bad spark plug. Dirty air filter. • Dirty fuel filter. • Water in fuel. • Loose or damaged wiring. • Carburetor out of adjustment. • Engine valves out of adjustment. Hard to start • Dirty air filter. • Bad spark plug. • Weak or dead battery. • Dirty fuel filter. • Stale or dirty fuel. • Loose or damaged wiring. • Carburetor out of adjustment.
TROUBLESHOOTING PROBLEM CHART CORRECTION CAUSE Loss of power • Cutting too much grass/too fast. • Throttle in "CHOKE" position. • Build-up of grass, leaves and trash under mower. Dirty air filter. Low oil level/dirty oil. • Faulty spark plug. • Dirty fuel filter. • Stale or dirty fuel. • Water in fuel. • Spark plug wire loose. • Dirty engine air screen/ fins. • Dirty/clogged muffler. • Loose or damaged wiring. • Carburetor out of adjustment. • Engine va,lves out of adjustment.
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Poor grass discharge • Engine speed too slow, • Travel speed too fast. • Wet grass. • Mower deck not level. • Low/uneven tire air pressure. • Worn, bent or loose blade. • Buildup of grass, leaves and trash under • Place throttle control in "FAST" position. • Shift to slower speed. • Allow grass to dry before mowing. Level mower deck. Check tires for proper air pressure. • Replace/sharpen blade. Tighten blade bolt. !. Clean underside of mower housing.
TRACTOR- MODEL NUMBER 917.273061 SCHEMATIC RED BATTERY SOLENOID REO FUSE AMMETER (OPTIONAL) WHITE WHITE _K BLACK SEAT SWITCH CHARGING SYSTEM REGULATOR OUTPUT w _roSWITCH RELAY ON C + F, 8 + E_ A + D HEADLIGHTS GFC IGNITION POSITION SWITCH CIRCUIT OFF M+G+A1 ON +LIGH_ B+A1 ON B + A1 START E+S+A' REMOVABLE CONNECTIONS NON-REMOVABLE CONNECTIONS H B "MAKE" NONE L+A2 NONE NONE D A ENGINE CONNECTOR (PURPLE WIRE, REGULATOR RED WIRE) _ENGINE w,.,.G INSULATED CU.S C_.SU.ETO.
TRACTOR -- MODEL NUMBER 917.273061 ELECTRICAL 22 43 33 r ....
TRACTOR - MODEL NUMBER 917.273061 ELECTRICAL KEY PART NO. NO. 1 2 8 10 11 12 16 19 20 21 22 24 25 26 27 28 29 30 33 40 41 42 43 45 50 52 81 83 144927 74760412 7603J 145211 150109 145769 153664 STD551125 73350400 166184 4152J 4014J 146686 108824X 73510400 157899 160784 163968 140403 166176 17720408 131563 145673 122822X 154963 141940 109748X 163996 DESCRIPTION Battery Bolt Hex Head 1/4-20 x 3/4 Tray, Battery Bolt 1/4-20 x 7.
TRACTOR- MODEL NUMBER 917.
TRACTOR -- MODEL NUMBER 917.273061 CHASSIS AND ENCLOSURES KEY PARr NO. NO. DESCRIPTION 1 2 4 5 6 7 8 14 15 16 17 18 19 20 21 23 24 28 30 31 32 33 34 35 36 37 39 49 42 43 44 45 47 50 RaiI, FrameRH Drawbar, Gt Nut, Lock Hex 7/16 Unc Dash YTGT 2 Cyl Dash, LowerVgt One Piece Screw, Thd Cut 1/4-20 x t/2 Support, Battery HoodAsm., PntYTGT Lens Asm Headlight Bar Cover, Access Screw, Thdrol 3/8-16x3/4 Grille Washer 13/82x13/16x12Ga.
TRACTOR GROUND -- MODEL NUMBER 917.
TRACTOR - MODEL NUMBER 917.273061 GROUND DRIVE KEY PART NO. NO. 1 ......
TRACTOR-- MODEL NUMBER 917.
TRACTOR -- MODEL NUMBER 917.273061 STEERING KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 44 45 Wheel, Steering Axle Asm., Front Fitting, Grease SpindleAsm, LH Spindle Asm., RH Bearing, Race Thrust Harden Washer 25/32 x 1-5/6 x 16 Ga. Ring, Klip#T5304-75 Cap, Spindle Bolt, Fin Hex 5/8-11 x 2-3/4 Spacer Bearing Axle Front Nut, Lock Flange 5/8-11 Unc Washer 25/32 x 1-1/4x 16 Ga.
TRACTOR-- MODEL NUMBER 917.
TRACTOR -- MODEL NUMBER 917.273061 ENGINE KEY PART NO. NO. 2 5 7 8 9 10 11 12 15 16 17 18 19 20 21 22 24 25 26 27 28 29 33 35 37 38 39 40 41 42 ,4.
TRACTOR -- MODEL NUMBER 917.273061 SEAT ASSEM BLY KEY PART NO. NO. 1 140124 2 140551 3 140675 4 127018X 5 145006 6 STD541437 7 124181X 8 150176 10 155925 12 121246)( 13 121248X DESCRIPTION Seat Bracket, Pivot Seat Strap, Fender Bolt, Shoulder 5/16-15 x .62 Clip, Push In, Hinged Nut, Crownlock 3/8-16 Unc Spring, Seat Cprsn Bolt 5/16-18 Unc x 3/4 w/Seres Pan, Seat Bracket, Mounting Switch Bushing, Snap KEY PART NO. NO.
TRACTOR -- MODEL NUMBER 917.273061 DECALS 17 17 18 25 25 9 5 12 22 KEY PART NO. NO. 1 164094 2 149516 3 163916 4 163917 5 140837 6 133644 7 164757 8 164884 9 163204 10 156439 11 4900J 12 146790 KEY PART NO. NO.
TRACTOR -- MODEL NUMBER 917.
TRACTOR-- MODEL NUMBER 917.273061 LIST ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 29 30 31 32 33 34 35 38 39 40 41 42 43 70 72 Rod Asm., Lever Shaft Asm., Lift Vgt Lever Asm., Lift Rh E-RingTruarc#5133-87 Washer 29/32 x 1-1/4 x 16 Ga. Bolt, Fin Hex 3/8-16 x 1-1/2 Grip, Handle Fluted Button, Plunger Pionger, Button Spring 2-1/8" Link Lift Retainer, Spring Arm, Suspension Vgt Beadng Nut, Crownleck 3/8-18 Unc Spring Asm.
TRACTOR -- MODEL NUMBER 917.
TRACTOR-- MODEL NUMBER 917.273061 MOWER DECK KEY PART NO. NO. 1 156990 2 STD541431 3 72110506 4 7631J 5 138457 6 STD624008 7 130832 8 850857 9 STD551137 10 140296 11 12 13 137380 129895 137553 14 15 16 17 18 19 20 21 22 23 24 25 27 28 30 137152 110485X 140329 106735X 19111016 105304X 123713X 137607 110452X 110509X 136320 19111216 STD551037 132823 157722 31 137266 32 153535 33 129963 34 72140610 35 72110616 36 72110608 37 137166 38 156085 KEY PART NO. NO.
TRACTORTRANSAXLE--MODEL MODEL NUMBER 917.
TRACTOR -- MODEL NUMBER 917.273061 TRANSAXLE--MODEL NUMBER 222-3010L KEY PART NO. NO. 1 2 7 16 20 164591 164592 153765 142876 142877 21 22 33 35 36 37 38 142878 142879 142929 142880 142882 142883 142884 39 40 41 42 43 45 46 47 49 63 64 142885 142886 142887 142888 142889 142890 142891 142892 153766 142894 150818 65 67 68 69 70 71 142897 142898 142899 142900 142901 142902 KEY PART NO. NO. DESCRIPTION Assembly, Housing, LH Assembly, Housing, RH Oil Seat .984 x 1.5 x .
TRACTOR TRANSAXLE--MODEL KEY NO. 1 2 3 4 5 6 8 12 13 14 15 17 19 21 22 23 PART NO. 144569 122716X 122745X 122715X 122700X 122699X 122767X 122717X 122748X 122749X 144571 122770X 153801 122722X 144573 142978 -- MODEL NUMBER NUMBER 917.273061 222-3010L KEY PART NO. NO.
TRACTOR -- MODEL NUMBER 917.273061 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 STARTING SYSTEM J ENGINE CONTROLS J 5 _3 %, 4 2 t 5 1/4 S _i/S__ ,o,-..,_,/_L,,_.ll_ ,o 7_Q ! 22 18 13 I IL PAN / LUBRICATION I 0 l @ 0-- 2 --3 _j., 4 .
TRACTOR-KOHLER ENGINE-MODEL STARTING KEY NO. MODELNUMBER NUMBER CV20S, TYPE NUMBER 65551 OIL PAN/LUBRICATION SYSTEM PART NO. M-0839070 2 3 24-096-05 M-0839080 4 5 6 7 6 9 10 11 12-468-01 25-098-05 12-221-01 12-227-13 12-211-01 124755-54 12-227-06 12-170-05 DESCRIPTION KEY NO. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO. PART NO. M-0645025 Screw, hex. flange M8x1.25x70 Cover, pinion Screw, hex. flange M8x1.
TRACTOR -- MODEL NUMBER 917.273061 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 IGNITION/ELECTRICAL I BLOWER HOUSING AND BAFFLES I 12 s_- v J "--__ U .
TRACTOR -- MODEL NUMBER 917.273061 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 BLOWER HOUSING & BAFFLES IGNITION/CHARGING KEY NO. PART NO. DESCRIPTION 1 54-755-15 Kit, grass screen (Includes 2-4,and 24 113 2 M.0403025 Screw, hex. cap M4x0.7x25 KEY NO. PART NO.
TRACTOR -- MODEL NUMBER 917.273061 KOHLER ENGINE-MODEL NUMBER CV20S, TYPE NUMBER 65551 CYLINDER HEAD, VALVE AND BREATHER I j16 ,\ _17 21 2s, I'_ll _,.
TRACTORKOHLER ENGINE-MODEL MODEL NUMBER 917.273061 NUMBER CV20S, TYPE NUMBER 65551 HEAD/VALVE/BREATHER CRANKCASE KEY NO. KEY NO, PART NO.
TRACTOR-- MODEL NUMBER 917.
TRACTOR -- MODEL NUMBER 917.273061 KOHLERENGINE-MODELNUMBERCV20S,TYPENUMBER65551 CRANKSHAFT KEY NO. 1 2 FUEL SYSTEM PART NO. DESCRIPTION 24-014-72 52-139-09 Crankshaft Plug, cup (Includes KEY NO. 2) PART NO. 1 24-853-25 2 3 24-041-15 EXHAUST KEY NO. 1 2 PART NO. DESCRIPTION 24-041-02 25-072-04 Gasket, exhaust (2) Stud, M8x1.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL I _!] /,_ AJk O i| Operate your Tractor up and down the face of slopes (not greater than 15°), never across the face. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes.
For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME'" (1-800-469-4663) Para pedir servicio de reparacibn a domicilio 1-800-676-5811 In Canada for all your service and parts needs call Au Canada pour tout le service ou les pieces 1-800-665-4455 For the repair or replacement parts you need: Call 6 am - 11 pm CST, 7 days a week PartsDirect sM 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio 1-800-659-7084 For the location of a Sears Parts a
