OWNER'S MANUAL JCRRFTSMRNI 6.0 Horsepower 2400 PSI 2.4 GPM High Pressure Washer Model No919.670280 • Safety • • • • WARNING: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Assembly Operation Maintenance Parts List • Fran(_ais Sold D20590 Re¥,0 _15/00 by Sears Canada, Inc., Toronto, Ont.
Warranty Safety ........................................................... Guidelines- Safety Guidelines Definitions ......................... ......................................... 2 Storage 2 Troubleshooting Parts ............................................................... Pump Parts .............................................. ..................................................... 5-7 Operation ...................................................
Improper operation or maintenance of this product could result in serious injury and property all warnings and operating instructions before using. HAZARD RISK OF EXPLOSION OR FIRE WHAT CAN HAPPEN • Spilled gasoline and it's vapors can become ignited from cigarette sparks, electrical arcing, exhaust gases, and hot engine components such as the muffler. • Heat will expand fuel in the tank which could result in spillage and possible fire explosion.
HAZARD WHAT CAN HAPPEN • Spray directed at electrical outlets or switches, or objects connected to an electrical circuit, could result in a fatal electrical shock. HOW TO PREVENT IT • Unplug any electrically operated product before attempting to clean it. Direct spray away from electric outlets and switches. ELECTRICAL SHOCK Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury.
The powerful spray from your pressure washer is capable of causing damage to fragile surfaces such as: wood, glass, automobile paint, auto stripping and trim, and delicate objects such as flowers and shrubs. Before spraying, check the item to be cleaned to assure yourself that it is robust enough to resist damage from the force of the spray. Avoid the use of the concentrated spray stream except for very strong surfaces like concrete and steel.
Tools Required for Assembly Mount the rubber isolator to the frame. To mount isolator place threaded end of bolt through the washer. 3, Adjustable wrench 5 mm Allen wrench (supplied) Remove Pressure Washer • Next with washer on bolt place threaded end of bolt through the larger hole in bottom of the rubber isolator• • Place threaded portion of bolt through the same hole location the wood plank was mounted to on the pressure washer.
, Place assembled washer holder. gun and wand on pressure , Place pull cord into the wire bracket holder. ,, Pull the cord under the wire bracket to the right of the wire loop. Gun/Wand Holder • Lift the pull cord handle up and slide the cord to the left, sliding the cord into the wire loop. • Next slide handle behind the wire bracket to the left of the wire loop. • Engine recoil will pull the cord into its final position.
Before • , CAUTION: Always check engine oil level before every start. Running engine low of oil or out of oil could result in serious damage. Note: included with your unit is a video cassette that demonstrates how to operate your pressure washer. If you have a video cassette recorder you should view the video before operation. Stopping Your Pressure I Engine Oil I Washer A CAUTION: Do not run pump without the water supply connected and turned on. Failure to do so will result in pump damage.
Use clean, fresh, regular unleaded gasoline with a minimum of 85 octane. De not mix oil with gasoline. if unleaded fuel is unavailable leaded fuel may be used. IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, hose or tank during storage. Also, experience indicates that alcohol-blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage.
How To Use Your Adjusting • Pressure Chemical Washer • Flow Turn the knob on the high pressure soap wand to adjust the soap flow. Turn knob counterclockwise for more soap (+) and clockwise for less soap (-). Start the pressure washer as outlined in the "To Start Your Pressure Washer" paragraph on page 9. _LWARNING: Stand on a stable surface and grip gun/wand firmly with both hands. Expect the gun to k ck when triggered.
CUSTOMER RESPONSIBILITIES MAINTENANCE TABLE Every 25 Before each use _hoors or year y TASK Every 50 hours or yearly Every 100 hours or yearly PRESSURE WASHER Check/clean inlet screen. x ICheck hioh pressure hose. Check soap and chemical hose and filter iCheck gun and wand for leaks.
Pressure Washer Maintenance Check and Clean Inlet Screen: Examine inlet screen on pump inlet fitting. Clean if clogged; replace if torn. Check High Pressure Hose: High pressure hose can develop leaks from wear, kinking, abuse. Inspect hose each time before use. Check for cuts, leaks, abrasions or bulging of cover, and damage or movement of couplings. If any of these conditions exist, replace hose immediately. (Changing • Replace oil drain plug and tighten securely. • Refill engine with oil and fuel.
Changing • Engine Clean Oil Change oil while engine is still warm. Preferably drain oil from top of engine as illustrated below. Drain oil with air cleaner side up. Oil can be drained from engine bottom if necessary. IMPORTANT: Before tipping engine or equipment to drain oil, drain fuel from tank by running engine until fuel tank is empty. To drain oil from bottom of engine, remove drain plug as illustrated below. Allow oil to drain and replace drain plug.
Carburetor The carburetor of your high pressure washer is pre-set at the factory. The carburetor should not be tampered with. If your pressure washer is used at an altitude in excess of 5000 feet consult with your nearest Sears Service Center regarding high altitude set changes• • Shut off the pressure washer and turn off the water supply• • Disconnect spark plug wire. • Pull trigger on gun handle to relieve any water pressure• Disconnect the wand from the gun.
Preparing Pressure Washer for Storage A CAUTION: While preparing the engine make sure water supply is turned on and flowing to the unit. NEVER run unit without water supply running through pump. Failure to do so will cause pump damage. NOTE: If you do not plan to use your unit for 30 days or more, unit should be prepared for storage. IMPORTANT; It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, hose or tank during storage.
SYMPTOM CAUSE SOLUTION Engine won't start 1. Engine throttle is in "OFF" Position. 2. Choke lever has not been placed to choke. 3. Pressure buildup after initial use. 1, Slide throttle to "Run" position. 2, Slide choke lever to choke position. 3. Depress trigger gun. Won't Draw Chemical 1. Turn knob counterclockwise for more soap (+). 1. Adjustment knob on soap nozzle is turned fully clockwise for less soap (-). 2. Chemical screen is obstructed. 2. Check chemical screen; clean if obstructed. 3.
CRAFTSMAN 2400 PSI HIGH PRESSURE WASHER 919.670280 19 <:_m23 21 REF NO. PART NUMBER DESCRIPTION 1 2 3 4 5 6 7 8 11 12 13 14 15 16 17 19 900 D20588 C042 17628 17709 W137 17926 W131 17713 D20587 D20181 17569 F064 F469 17712 17716 17367 ..... 20 23 24 PK18148 Fl12 AL-650015 Handle, Bagged Knob - 5/16" Gun Tire Semi (8x2") Nut Pal 1/2" Rubber Foot, Hotlow Tee Nut 5/160" x 3/4" Frame Wand,High Pressure Soap Hose. 1/4" X 25 ft.
CRAFTSMAN 2400 PSI HIGH PRESSURE WASHER 919.670280 PUMP BREAKDOWN MODEL PK18148 Bottom View P _ 2..2 26 \26-3 26-5 Torque to 170-180 OF_[E NTATION V}E3N REF ITEMS 22 THRU 25 //I 14 TOFiQUE TO ADD TEFLON 150 IN-LB TAPE TO THREADS / // TORQUE 110-!20 TO IN.
CRAFTSMAN 2400 PSI HIGH PRESSURE WASHER 919.670280 K e.e_y_# 1 3 4 5 6 7 8 10 11 12 16 17 18 19 20 21 22 23 24 25 26 26-2 26-3 26-4 26-5 26-6 27 28 29 31 32 Chemical PK18148 Injector part, order the kit. 18301Oil Seal Kit, contains Key #s 20 17323 Valve Kit, contains Key#s 26-2 18246 Water Seal Kit contains Key#'s 17324 Bearing Kit contains Key #'s 5 NOTE: When ordering needed.
CRAFTSMAN 2400 PSI HIGH PRESSURE WASHER 919.670280 584 _ BRIGGS ENGINE MODEL #120612-0152-E10 684 '_ 585 267 842 525_ / 524_) I 404 6,6 REF NO. PART NO. 1 2 692670 399269 3 8 9 10 11 227 499675 691467 287 306 DESCRIPTION / REF NO. 566 1 PART NO.
CRAFTSMAN 2400 PSI HIGH PRESSURE WASHER 919.670280 BRIGGS ENGINE MODEL #120612-0152-E10 383_ 914 _' I I REF NO. PART NO. DESCRIPTION 5 7 695276 695166 Cylinder Cylinder Gasket 13 691137 33 34 35 36 499642 499641 691304 691304 Screw (Cylinder Head) Exhaust Valve Intake Valve 40 45 692194 690977 Head Head Valve Spring (intake) Valve Spring (Exhaust) Valve Retainer Valve Tappet REF NO. PART NO.
CRAFTSMAN 2400 PSI HIGH PRESSURE WASHER 919.670280 BRIGGS ENGINE MODEL #120612-0152-E10 741"_-_ e REF NO. o2o_9oR_ o :_1_'c_ PART NO. 4 12 15 16 20 22 499619 692232 691680 695487 399781 891092 24 25 222698 690021 25 25 694167 25 694168 20@ REF NO. DESCRIPTION PART NO, Engine Sump Crankcase Gasket 25 694169 Oil Drain P]ug Crankshaft 26 26 26 26 26 27 28 29 32 43 46 146 741 499631 Oil Seal (PTO Side) Screw (Crankcase Cover) Flywheel Key Piston Assembly (Standard) ....
CRAFTSMAN 2400 PSi HIGH PRESSURE BRIGGS ENGINE MODEL #120612-0152-E10 WASHER 919.670280 365 692 JR 122U _ 276 I j,._ 95_ __. ........ :,76Q 51 334' 18 8 _ REF NO. PART NO.
CRAFTSMAN 2400 PSI HIGH PRESSURE WASHER 919.670280 BRIGGS ENGINE MODEL #120612-0152-E10 425 443A_ 968 445 529A 613_ 883 957 670 REF PART NO. NO. 163 187 190 300 425 692667 691O50 690940 694248 690670 443 691637 443A 692523 ceoss0 r_ 0 3/_stce _) DESCRIPTION Air Cleaner Gasket Fuel Line Screw (Fuel Tank) Exhaust Muffler Screw (Air Cleaner Cover) Screw (Air Cleaner Primer Base) Screw (Air Cleaner Primer Base) REF PART NO. NO.
CRAFTSMAN BRIGGS ENGINE MODEL #120612-0152-E10 2400 PSI HIGH PRESSURE WASHER 919.670280 1036 EMISSIONS LABEL 332 3os 930 373 _ 100_ sosl 23 ss _ 592@ 55 58_,_.,_ .... I 689 12110 456 I_ 597 1210_ I REF NO. PART NO. 23 37 55 692693 694086 691421 58 693389 60 65 281434 690837 78 691108 REF NO. PART NO.
CRAFTSMAN 2400 PSI HIGH PRESSURE WASHER 919.670280 BRIGGS ENGINE MODEL 358 ENGINE GASKET #120612-0152-E10 SET 585 122( 842 0 1095 VALVE GASKET 121 CARBURETOR SET OVERHAUL KIT 127 276 137 O 633 O 633A O 122_ 977 CARBURETOR GASKET SET 633 O 276 (_ 122 REF NO. PART NO. 3 7 299819 695166 9 12 20 272481 692232 399781 51 104 121 692668 691242 692703 o_90 R_,.
-ENG o_o69o R_,0 _51oo
OWNER'S MANUAL The model number of your Sears Air Compressor can be found on the maintenance label on the top of the shroud or on the bar code label on the rear of the air tank. MODEL NO. 919.670280 SERVICE CALL SERVICE AND REPAIR PARTS 1-800-665-4455" Keep this number handy should you require a service call or need to order repair parts. If ordering parts make sure you have the name, make and model no. of the merchandise and the name and number of the part you wish to order.