Owner's Manual II:RRFTSMRN'I Single Speed / Reversible 318 in. PROFESSIONAL CORDLESS DRILL-DRIVER Model No. 973.274950 Save this manual for future reference ;A CAUTION: Read and follow all Safety Rules_and Operating Instructions before first use of this product. Sears, Roebuck 972000-528 4-98 and Co.
• Warranty......................................................................................................................................................... 2 • Introduction and Product Specifications ......................................................................................................... 2 • Rules For Safe Operation ..:........................................................................................................................ 3-5 A.
Thepurposeof safetysymbolsIsto attractyour attentionto possibledangers.Thesafetysymbols,and the explanationswiththem,deserveyourcarefulattentionandunderstanding.Thesafetywarningsdo not by themselveseliminateanydanger.TheInstructionsor warningsthey givearenot substitutesfor properaccidentpreventionmeasures. SYMBOL A MEANING SAFETY ALERT SYMBOL: Indicateswarningor caution.May be usedin conjunctionwith othersymbolsor pictographs.
RULESFORSAFEOPERATION(Continued) • _ NEVER USE IN AN EXPLOSIVE ATMO- DO NOT PLACE BATFERY TOOLS OR THEIR SPHERE. Normal sparking of the motor could ignite flammable liquids, gases, or fumes. M • BATTERIES NEAR FIRE OR HEAT. They may explode. KEEP HANDLES DRY, CLEAN, AND FREE FRO• OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products or any strong solvents to clean your tool. STAY ALERT. Watch what you are doing and use common sense.
RULES FOR SAFE OPERATION (Continued) B ' An extension cord should not be used unless • absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. • Do not disassemble charger; take it to a qualified serviceman when service or repair is required.
Thefollowingrecommended accessories arecurrentlyavailableatSearsRetailStores, • 6-Pc, Extra Length Magnite Power Bit Set • 30-Pc. Power ScrewdrivedNutddver Set and Case • 17-Pc. Power Screwdriver/Nutddver Set and Case • High Speed Bits (For Wood or Metal)......3/4.inch Max, • Keyless Chuck (Item No. 9-20988) _LWARNING: KNOW The use of aHachments or accessories not listed might be hazardous. WRIST YOUR DRILL-DRIVER STRAP See Figure 1. See Figure 1.
,_ If battery pack is deeply discharged, red light should become steady after voltage has increased, normally within 30 minutes. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. If after one hour red light is still flashing, this indicates a defective battery pack and should be replaced.
SWITCH TO INSTALL See Figure 2. • Lock switch trigger on your drill by placing the direction of rotation selector in center position. See Figure 2. • Place battery pack in your drill. Align raised rib inside drill with groove on battery pack. See Figure 3. To turn your drill ON, depress the switch tdgger. To turn it OFF, release the switch trigger. CENTERPosmoN (LOCK BATTERY PACK SELECTOR SWITCH TRIGGER BATTERYPACK 1_ Fig. 2 SWITCH LOCK LATCHES See Figure 2.
REVERSIBLE KEYLESS CHUCK See Figure 4. See Figure 6. This tool has the feature of being reversible. The direction of rotation is controlled by a selector located above the switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch for drilling. The drilling direction isreversad when the selector is to the right of the switch. When the selector is in center position, the switch trigger is locked.
INSTALLING BITS REMOVING See Figure 7. See Figure 7. Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 2. Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 2. Open or close chuck jaws to a point where the Loosen the chuck jaws from drill bit. opening is slightly larger than the bit size you intendtouse.Also,raisethefront of your drill slightly to keep the bit from falling out of the chuck jaws.
BIT STORAGE DRILLING See Figure 10. See Figure12. When not in use, bits provided with your drill can be placed in the storage area located on the top of your drill as shown in figure 10. SCREWDRIVER BITS BITSTORAGEAREA Fig. 10 WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. Fig.
CHUCK REMOVAL Insert allen wrench in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It can now be unscrewed by hand. See Figure 15. See Figures 13, 14, and 15. The chuck must be removed in order to use some accessories. To remove: • Lock the switch tdgger by placing the direction of rotation selector in center position.
,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Do not abuse power tools. Abusive practices can damage tool as well as workpiece. Only the parts shown on parts list, page fifteen, are intended to be repaired or replaced by the customer. All other parts should be replaced by a qualified service technician at an authorized service facility. Avoid using solvents when cleaning plastic parts.
Topreservenaturalresources, please recycleor disposeofexpiredbattery packproperly. BA'n'ERY PACK REMOVAL PREPARATION AND FOR RECYCLING WARNING: Upon removal, cover the battery pack's terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Nickelcadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children.
CRAFTSMAN PROFESSIONAL MODEL 3/8 Inch CORDLESS NO. 973.274950 DRILL-DRIVER | I number in all correspondence regarding your 3/8 in. CORDLESS DRILL-DRIVER or when ordering The model numberwill be found on a plate attached to the motor housing. Always mention the model repair parts. | SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 1 5 3 4 PARTS LIST Key No. Part Number Description 1 616478-003 Screw (Special) ............................................. 1 2 973015-001 Chuck (Item No.
Forthe repair or replacementpartsyouneed delivereddirectlyto yourhome Call7 am - 7 pm,7 daysa week 1-800-366-PART (1-800-366-7278) Forrepairservice Call24 hours a day,7 daysa week 1.800.4.REPAIR (1-800-473-7247) Forthelocationof a SearsPartsandRepairCenterinyourarea Call24 hours a day,7 daysa week 1-800-488-1222 mnmmmm mmmmmm The modelnumberof thistoolwill be foundona serial plate attachedto the motorhousing.
