Use And Care Manual

ENGLISH
10
Versatrack Variables
1ST_Figure 1ST_Callout 2ND_Callout
K 11 12

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the Versatrack™ hang
hook is securely tightened.

WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the hanghook.

WARNING: Ensure that the tool weight does not
exceed the maximum rated weight for the selected
Versatrack™ hook.

WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to
not exceed 75 lb (35 kg) per linear foot.
IMPORTANT: When attaching the Versatrack™ hang
hook, use only the screw that is provided. Be sure to
securely tighten the screw. Versatrack™ accessories
mount compatible tools securely to the Versatrack™
Trackwallsystem.
1. Turn tool off, remove the battery pack and
removeaccessories.

CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
theVersatrack™ Trackwall.
2. Attach the hang hook
11
on the tool.
a. Place the Versatrack™ hang hook onto the mounting
location at the base of the tool.
b. Use a screwdriver to secure the hang hook with the
provided screw
12
. Do not use any other screw for this.
NOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
11
Fig. K
12
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performingthis.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into aliquid.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury.
Accessories

WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with thisproduct.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
NOTE: In areas where blade visibility is limited, use the
edge of the pivoting shoe as aguide.
Fig.J
Project Tips
• Cut only with sharp blades; they cut cleaner, faster and put
less strain on the motor whilecutting.
• When cutting, always ensure that the pivoting shoe
is resting against the workpiece. This will improve
operator control and minimizevibration.
• For longer blade life, use bi-metal blades. These
utilize a carbon steel back welded to high speed steel
teeth making the blade more flexible and less prone
tobreaking.
Versatrack™ (Fig. K)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury.

WARNING: To reduce the risk of serious personal
injury, do not use a damaged Versatrack™ hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
hang hook or Versatrack™ Trackwall will not support
the weight of the tool.