Instruction Manual
Table Of Contents
- English (United States)
- INTRODUCTION
- INSTALLATION
- ADJUSTMENT
- myQ® SMARTPHONE CONTROL
- OPERATION
- TROUBLESHOOTING
- REPAIR PARTS
- Accessories
- Warranty
- Automatic Garage Door Opener Safety & Maintenance Guide
- Repair Parts and Service
- Español (México)
- INTRODUCCIÓN
- Revisión de los símbolos y términos de seguridad
- Operación en estado pasivo
- Preparación de la puerta de garaje
- Pruebe la intensidad de la señal de Wi-Fi® en el garaje.
- Herramientas necesarias
- Planificación
- Contenido de la caja
- Inventario de herrajes
- ENSAMBLAJE PASO 1
- Ensamblaje Paso 2
- ensamblaje paso 3
- Ensamblaje paso 4
- Ensamblaje paso 5
- Ensamblaje paso 6
- INSTALACIÓN
- AJUSTES
- CONTROL myQ® PARA TELÉFONOS INTELIGENTES
- FUNCIONAMIENTO
- RESOLUCIÓN DE PROBLEMAS
- Piezas de repuesto
- Accesorios
- Garantía
- Guía de seguridad y mantenimiento del abre-puertas de garaje automático
- Piezas de repuesto y servicio
- INTRODUCCIÓN
INSTALLATION STEP 6
INSTALL THE LIGHTS
1. Press the release tabs on both sides of lens. Gently rotate lens back and
downward until the lens hinge is in the fully open position. Do not
remove the lens.
2. Insert an A19 incandescent (100 watt maximum) or compact fluorescent
(26W, 100W equivalent) light bulb into the light socket. The lights will
turn ON and remain lit for approximately 4-1/2 minutes when power is
connected. Then the lights will turn OFF.
3. Reverse the procedure to close the lens.
4. If the bulbs burn out prematurely due to vibration, replace with a garage
door opener bulb. Use A19, standard neck garage door opener for
replacement.
NOTE: Do not use halogen, short neck, or specialty light bulbs as these may
overheat the end panel or light socket. Do not use LED bulbs as they may reduce
the range or performance of your remote control(s).
To prevent possible OVERHEATING of the end panel or light socket:
l Use ONLY A19 incandescent (100W maximum) or compact fluorescent (26W
maximum) light bulbs.
l DO NOT use incandescent bulbs larger than 100W.
l DO NOT use compact fluorescent light bulbs larger than 26W (100W
equivalent).
l DO NOT use halogen bulbs.
l DO NOT use short neck or specialty light bulbs.
Release Tab
100 Watt (Max)
Standard Light Bulb
100 Watt (Max)
Standard Light Bulb
Compact Fluorescent
Light Bulb
Compact Fluorescent
Light Bulb
Lens
Hinge
or
or
INSTALLATION STEP 7
ATTACH THE EMERGENCY RELEASE ROPE AND HANDLE
1. Insert one end of the emergency release rope through the handle. Make
sure that “NOTICE” is right side up. Secure with an overhand knot at least
1" (2.5 cm) from the end of the rope to prevent slipping.
2. Insert the other end of the emergency release rope through the hole in the
trolley release arm. Mount the emergency release within reach, but at least
6 feet (1.83m) above floor, avoiding contact with vehicles to prevent
accidental release and secure with an overhand knot.
NOTE: If it is necessary to cut the emergency release rope, seal the cut end with a
match or lighter to prevent unraveling. Ensure the emergency release rope and
handle are above the top of all vehicles to avoid entanglement.
To prevent possible SERIOUS INJURY or DEATH from a falling garage door:
l If possible, use emergency release handle to disengage trolley ONLY when
garage door is CLOSED. Weak or broken springs or unbalanced door could
result in an open door falling rapidly and/or unexpectedly.
l NEVER use emergency release handle unless garage doorway is clear of
persons and obstructions.
l NEVER use handle to pull door open or closed. If rope knot becomes untied,
you could fall.
Trolley
Release Arm
Emergency
Release Handle
Overhand
Knot
Trolley
18