Instruction Manual
Table Of Contents
- English (United States)
- INTRODUCTION
- INSTALLATION
- ADJUSTMENT
- myQ® SMARTPHONE CONTROL
- OPERATION
- TROUBLESHOOTING
- REPAIR PARTS
- Accessories
- Warranty
- Automatic Garage Door Opener Safety & Maintenance Guide
- Repair Parts and Service
- Español (México)
- INTRODUCCIÓN
- Revisión de los símbolos y términos de seguridad
- Operación en estado pasivo
- Preparación de la puerta de garaje
- Pruebe la intensidad de la señal de Wi-Fi® en el garaje.
- Herramientas necesarias
- Planificación
- Contenido de la caja
- Inventario de herrajes
- ENSAMBLAJE PASO 1
- Ensamblaje Paso 2
- ensamblaje paso 3
- Ensamblaje paso 4
- Ensamblaje paso 5
- Ensamblaje paso 6
- INSTALACIÓN
- AJUSTES
- CONTROL myQ® PARA TELÉFONOS INTELIGENTES
- FUNCIONAMIENTO
- RESOLUCIÓN DE PROBLEMAS
- Piezas de repuesto
- Accesorios
- Garantía
- Guía de seguridad y mantenimiento del abre-puertas de garaje automático
- Piezas de repuesto y servicio
- INTRODUCCIÓN
INSTALLATION STEP 9
CONNECT DOOR ARM TO TROLLEY
Follow instructions which apply to your door type as illustrated below and on the
following page.
IMPORTANT: The groove on the straight door arm MUST face away from the curved
door arm (Figure 4).
SECTIONAL DOORS ONLY
1. Make sure garage door is fully closed. Pull the emergency release handle
to disconnect the outer trolley from the inner trolley. Slide the outer trolley
back (away from the pulley) about 8" (20 cm) as shown in Figures 1, 2 and
3.
2. Fasten straight door arm section to outer trolley with the 5/16"x1" clevis
pin. Secure the connection with a ring fastener (Figure 1).
3. Fasten curved section to the door bracket in the same way, using the
5/16"x1-1/4" clevis pin.
4. Bring arm sections together. Find two pairs of holes that line up and join
sections. Select holes as far apart as possible to increase door arm
rigidity (Figure 2).
Hole alignment alternative (Figure 3):
l If holes in curved arm are above holes in straight arm, disconnect straight
arm. Cut about 6" (15 cm) from the solid end. Reconnect to trolley with cut
end down as shown.
l Bring arm sections together.
l Find two pairs of holes that line up and join with bolts, lock washers and
nuts.
Pull the emergency release handle toward the opener at a 45° angle so that the
trolley release arm is horizontal. Trolley will re-engage automatically when opener
is operated during the adjustments.
Lock Washer 5/16"
Nut 5/16"-18
Ring Fastener
Hex Bolt
5/16"-18x7/8"
Clevis Pin
5/16"x1" (Trolley)
Clevis Pin
5/16"x1-1/4" (Door Bracket)
HARDWARE SHOWN ACTUAL SIZE
Ring
Fastener
Door
Bracket
Straight
Door Arm
Curved Door Arm
Inner
Trolley
Outer
Trolley
Lock
Washers
5/16"
Nuts
5/16"-18
Door Bracket
Hex Bolts
5/16"-18x7/8"
Cut this end
Emergency
Release
Handle
Lock
Washers
5/16"
Nuts
5/16"-18
Hex Bolts
5/16"-18x7/8"
Clevis Pin
5/16"x1"
Clevis Pin 5/16"x1-1/4"
Pulley
Pulley
Pulley
Figure 1
Figure 2
Figure 3
8" (20 cm) min.
8" (20 cm) min.
8" (20 cm) min.
Figure 4
CORRECT INCORRECT
Straight
Door Arm
Straight
Door Arm
Curved
Door Arm
Curved
Door
Arm
(Groove
facing out)
21