How to Guide
Table Of Contents
- English (United States)
- Français (Canada)
- INTRODUCTION
- INSTALLATION
- RÉGLAGE
- BATTERIE DE SECOURS Modèle CMXEOCG982
- COMMANDE myQ® PAR TÉLÉPHONE INTELLIGENT
- FONCTIONNEMENT
- Caractéristiques
- Tableau de commande à double fonction Modèle CMXEOCG572
- Commande de porte Modèle CMXEOCG322
- Tableau de commande de détection de mouvement Modèles CMXEOCG772 et CMXEOCG982
- Télécommande et clavier sans fil
- Pour effacer la mémoire
- Ouverture manuelle de la porte
- La pile de la télécommande
- Soin de votre actionneur de porte
- DÉPANNAGE
- PIÈCES DE RÉPARATION
- ACCESSOIRES
- GARANTIE
- GUIDE DE SÉCURITÉ ET D’ENTRETIEN DE L’OUVRE-PORTE DE GARAGE AUTOMATIQUE
- Español (México)
- INTRODUCCIÓN
- INSTALACIÓN
- AJUSTES
- BATERÍA DE RESPALDO Modelo CMXEOCG982
- CONTROL myQ® PARA TELÉFONOS INTELIGENTES
- FUNCIONAMIENTO
- Características
- Panel de control de doble función modelo CMXEOCG572
- Control de la puerta Modelo CMXEOCG322
- Panel de control de detección de movimiento Para los modelos CMXEOCG772 y CMX...
- Control remoto y teclado inalámbrico
- Para borrar la memoria
- Para abrir la puerta manualmente
- La batería del control remoto
- Mantenimiento de su abre-puertas de garaje
- RESOLUCIÓN DE PROBLEMAS
- Piezas de repuesto
- ACCESORIOS
- GARANTÍA
- GUÍA DE SEGURIDAD Y MANTENIMIENTO DEL ABRE-PUERTAS DE GARAJE AUTOMÁTICO
ASSEMBLY STEP 6
INSTALL THE SPROCKET COVER
To avoid possible SERIOUS INJURY to finger from moving garage door opener:
• ALWAYS keep hand clear of sprocket while operating opener.
• Securely attach sprocket cover BEFORE operating.
1. Position the sprocket cover over the sprocket as shown and fasten to
the mounting plate with #8x3/8" hex screws provided.
Hex Screw #8x3/8"
(Packed with the
sprocket cover)
HARDWARE SHOWN ACTUAL SIZE
Hex Screws
Sprocket Cover
Hex Screws
Sprocket Cover
OR
You have now finished assembling your garage door opener. Please read the following
warnings before proceeding to the installation section.
INSTALLATION
IMPORTANT INSTALLATION INSTRUCTIONS
To reduce the risk of SEVERE INJURY or DEATH:
1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.
2. Install garage door opener ONLY on properly balanced and lubricated garage
door. An improperly balanced door may NOT reverse when required and could
result in SEVERE INJURY or DEATH.
3. ALL repairs to cables, spring assemblies and other hardware MUST be made by
a trained door systems technician BEFORE installing opener.
4. Disable ALL locks and remove ALL ropes connected to garage door BEFORE
installing opener to avoid entanglement.
5. Where possible, install the door opener 7 feet (2.13 m) or more above the floor.
6. Mount the emergency release within reach, but at least 6 feet (1.83 m) above
the floor and avoiding contact with vehicles to avoid accidental release.
7. NEVER connect garage door opener to power source until instructed to do so.
8. NEVER wear watches, rings or loose clothing while installing or servicing
opener. They could be caught in garage door or opener mechanisms.
9. Install wall-mounted garage door control:
• within sight of the garage door.
• out of reach of small children at a minimum height of 5feet (1.5m)
above floors, landings, steps or any other adjacent walking surface.
• away from ALL moving parts of the door.
10. Place entrapment warning label on wall next to garage door control in a
prominent location.
11. Place emergency release/safety reverse test label in plain view on inside of
garage door.
12. Upon completion of installation, test safety reversal system. Door MUST reverse
on contact with a 1-1/2" (3.8cm) high object (or a 2x4 laid flat) on the floor.
13. DO NOT install on a one-piece door if using devices or features providing
unattended close. Unattended devices and features are to be used ONLY with
sectional doors.
12