How to Guide
Table Of Contents
- English (United States)
- Français (Canada)
- INTRODUCTION
- INSTALLATION
- RÉGLAGE
- BATTERIE DE SECOURS Modèle CMXEOCG982
- COMMANDE myQ® PAR TÉLÉPHONE INTELLIGENT
- FONCTIONNEMENT
- Caractéristiques
- Tableau de commande à double fonction Modèle CMXEOCG572
- Commande de porte Modèle CMXEOCG322
- Tableau de commande de détection de mouvement Modèles CMXEOCG772 et CMXEOCG982
- Télécommande et clavier sans fil
- Pour effacer la mémoire
- Ouverture manuelle de la porte
- La pile de la télécommande
- Soin de votre actionneur de porte
- DÉPANNAGE
- PIÈCES DE RÉPARATION
- ACCESSOIRES
- GARANTIE
- GUIDE DE SÉCURITÉ ET D’ENTRETIEN DE L’OUVRE-PORTE DE GARAGE AUTOMATIQUE
- Español (México)
- INTRODUCCIÓN
- INSTALACIÓN
- AJUSTES
- BATERÍA DE RESPALDO Modelo CMXEOCG982
- CONTROL myQ® PARA TELÉFONOS INTELIGENTES
- FUNCIONAMIENTO
- Características
- Panel de control de doble función modelo CMXEOCG572
- Control de la puerta Modelo CMXEOCG322
- Panel de control de detección de movimiento Para los modelos CMXEOCG772 y CMX...
- Control remoto y teclado inalámbrico
- Para borrar la memoria
- Para abrir la puerta manualmente
- La batería del control remoto
- Mantenimiento de su abre-puertas de garaje
- RESOLUCIÓN DE PROBLEMAS
- Piezas de repuesto
- ACCESORIOS
- GARANTÍA
- GUÍA DE SEGURIDAD Y MANTENIMIENTO DEL ABRE-PUERTAS DE GARAJE AUTOMÁTICO
INSTALLATION STEP 9
CONNECT DOOR ARM TO TROLLEY
Follow instructions which apply to your door type as illustrated below and on the
following page.
IMPORTANT: The groove on the straight door arm MUST face away from the curved
door arm (Figure 4).
SECTIONAL DOORS ONLY
1. Make sure garage door is fully closed. Pull the emergency release handle to
disconnect the outer trolley from the inner trolley. Slide the outer trolley back
(away from the pulley) about 8" (20 cm) as shown in Figures 1, 2 and 3.
2. Fasten straight door arm section to outer trolley with the 5/16"x1" clevis pin.
Secure the connection with a ring fastener (Figure 1).
3. Fasten curved section to the door bracket in the same way, using the
5/16"x1-1/4" clevis pin.
4. Bring arm sections together. Find two pairs of holes that line up and join
sections. Select holes as far apart as possible to increase door arm rigidity
(Figure 2).
Hole alignment alternative (Figure 3):
• If holes in curved arm are above holes in straight arm, disconnect straight
arm. Cut about 6" (15 cm) from the solid end. Reconnect to trolley with cut
end down as shown.
• Bring arm sections together.
• Find two pairs of holes that line up and join with bolts, lock washers and
nuts.
Pull the emergency release handle toward the opener at a 45° angle so that the trolley
release arm is horizontal. Trolley will re-engage automatically when opener is
operated during the adjustments.
Lock Washer 5/16"
Nut 5/16"-18
Ring Fastener
Hex Bolt
5/16"-18x7/8"
Clevis Pin
5/16"x1" (Trolley)
Clevis Pin
5/16"x1-1/4" (Door Bracket)
HARDWARE SHOWN ACTUAL SIZE
Ring
Fastener
Door
Bracket
Straight
Door Arm
Curved Door Arm
Inner
Trolley
Outer
Trolley
Lock
Washers
5/16"
Nuts
5/16"-18
Door Bracket
Hex Bolts
5/16"-18x7/8"
Cut this end
Emergency
Release
Handle
Lock
Washers
5/16"
Nuts
5/16"-18
Hex Bolts
5/16"-18x7/8"
Clevis Pin
5/16"x1"
Clevis Pin 5/16"x1-1/4"
Pulley
Pulley
Pulley
Figure 1
Figure 2
Figure 3
8" (20 cm) min.
8" (20 cm) min.
8" (20 cm) min.
Figure 4
CORRECT INCORRECT
Straight
Door Arm
Straight
Door Arm
Curved
Door Arm
Curved
Door
Arm
(Groove
facing out)
21