,,,, ...... _ _.,,_t=,,_ * _ OWNER'S MANUAL MODEL NOS. 625.348571 625.348591 Caution: Read and Follow All Safety Rules and Operating Instructions Before First Use of This Product, Deluxe Demand Water Softeners ÷ Warranty Start Up / Setting Timer If you have questions when installing, operating or maintaining your softener, and when setting the timer, call this toll-free number ....
SEARS RESIDENTUAL WATER SOFTENER FULL ONE YEAR WARRANTY ON WATER SOFTENER For one year from the date of purchase, when this water softener is installed and maintained in accordance with our instructions, Sears will repair, free of charge, defects in material or workmanship in this water softener.
TABLE OF CONTENTS _i _'!" ....... ii! iii ii I_ I PAGE NO. SECTION 1 A, B. C, D, E_ A. B.
SECTION 1 WATER SOFTENER l 1A. SAFETY GUIDES [] Read all steps, guides and rules carefully before installing and using your new water softener. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water softener. [] Your water softener will remove hardness erals and "clear water" iron from water, up limits shown on page 19.
SECT_O 1 WATER SOFTENER START-UP f .,.4 1B, j i CHECK ,i., ,i, ,,,111 i1,,i Refer to the Installation for step-by-step guides i LIST OF ALL STEP-BY-STEP HIIIH,q.,I III Manual, , , p, U, ,,,,_.... GUIDES TO INSTALL iii IIII ................................ part no, 7159931, To be sure you have done al! the steps to install the softener, read the following list., Page numbers referred to are in the Installation Manual.
SECTION 1 WATE. SOFTENER START-UP i i lC. , ,,,,, signal light adjust PROGRAM THE TIMER ,, salt level adjust display UP button \ SELECT button / Deluxe Kenmore Water Une for Customer Assistance t -800-426-9345 Demand Water Softener with Dual Segment Electronic Display LOW0 SALT ON/OFF-HOLD button (Recharge Tonight-Now) When the transformer is plugged in, the model code SR31, and a test number (example: kl0) show in the face plate display for 4 seconds° Then, I2:00 /_,_ and PRESENT TIM
SECTION I WATER SOFTENER START-UP i i lC° PROGRAM J......... 2. _ SET WATER HARDNESS [] Press the SELECT button (flashing) i , NUMBER: once to display 25 and HARDNESS. The grains per gallon (gpg) hardness of your water supply is on your water analysis reporL Be sure to enter water test results on page 2, for future reference. THE TIMER ...............................
SECTION I WATER SOFTENER 1D. SANITIZING THE WATER SOFTENER ADD WATER Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener wilt not infect or contaminate your water supply, and will not cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the softener. For this reason, sanitizing as follows is suggested[] when installing_ 1.
SECTION 1 WATER SOFTENER START-UP J it ,i ii 1E. l l,l,i Brine (salt dissolved , ii ,Ul Ulll,ii i1,,,i,ii1,1 FILL THE STORAGE in water) iii is needed , .... lUUll,i u , ,ill!ll,_ll i lu,i TANK WITH SALT ,,,i i , ' i i iii .... ADD SALT for each and every regeneration_ The water for making b_ine is metered into the salt storage tank by the softener. However, you must keep the tank filled with salt.
SEOT_O 2 HOW YOUR WATER SOFTENER 2A. FACE PLATE TIMER FEATURES u u,,, i i ,, SALT MONITOR EXTRA RECHARGE Sometimes, a manually charge) may be desired, are: started regeneration (reor neede& Two examples 1. 2. You can start a regeneration right awa}; or you can set the timer to regenerate at the next 2:00 AM (or other preset recharge time), Do the following_ 3_ NOW button and hold until *RE,_C,A,G_ M PIess theServ ON/OFF-HOLD i°']_77t_p,, CHARGE, and fill begin to flash in the display, Upon __.
SECTION 2 .ow YOUR WATER SOFTE.ER WORKS i i 2A. FACE PLATE TIMER FEATURES OPTIONAL SETTINGS - CLEAN FEATURE MINUTES, MAXIMUM DAYS BETWEEN REGENERATIONS, and 12 / 24 HOUR TIME READINGS: WATER FLOW THROUGH THE SOFTENER If soft water is in use, the water flow bars continually scroll across the displa); The bars no water flow scroll slowly when water flow is slow, and move faster as water flow increases The flow bars do not show when all faucets and water using appliances are off_ Ftow_ 1.
SEOTnON 2 HowYourWATER SOFTENER WORKS t J 2B. SOFT WATER SERVlCE ....... i .......... v,, ,i,i AND REGENERATION ........... . ..... REGENERATION SERVICE When the softener is giving you soft water, it is called "Service"° During service, hard water flows through the house main water pipe into the softener° Inside the softener resin tank is a bed made up of thousands of tiny, plastic resin beads (FIG. 4)_ As hard water passes through the bed, each bead attracts and holds the hardness minerals.
SECTION 2 HOW YOUR WATER SOFTENER WORKS il i,i, ........... 2B. _n u,ii i n u.i SOFT WATER SERVICE AND REGENERATION WATER FLOW THROUGH THE SOFTENER IN BACKWASH F2qBRINING: During brining, the brine is moved from the salt storage area, into the resin tank, Inside the resin tank, brine cleans hardness minerals from the resin beads and they are discharged out the drain, How much brine is needed to clean the resin depends hard water 4_ bypass OUT a f nozzle and venturi (FIG.
SECTION 2 How YOUR WATER SOFTENER WORKS { J 2B. SOFT WATER SERVICE 'l AUTOMATIC .... AND REGENERATION ....................................
SECTmON 3 CARE OFYOUR SOFTENER i J ,llnu 3A. i i nlu,n,, SALT...REFILLING n ' ' nl ii ii ,lln STORAGE The Salt Monitor System (see page 10) will turn on the low salt light to warn you when to refill with salt. Check for a low salt light a few weeks after you install the softener, and every week after thatr Always refill at about the #2 salt monitor level. At this level, the tank is about 1/3 full. Never let the Ull A SALT .........................
SECTION 3 CA.EOFYOUR SOFTE.ER [ I 3B. KEEPING THE WATER SOFTENER CLEAN NOTE: COVERS Never use cleaners having amanonia or abrasives. They may scratch and dull the surfacer To keep your new Kenmore water softener looking nice, apply a coat of paste wax and repeat once a year. When dusty, wipe it with a damp cloth to keep it sparkling. CLEANING VENTURI NOZZLE & VENTURI A clean nozzle and venturi (FIG.
SECTION 3 3C. CARE OFYOUR SOFTENE. KEEP THE SOFTENER ...... ,i i,, ,,,_,,.n;_ .... ,,,i FROM FREEZING i, i, i, ,i, ,,1111 iii ..._._.._alJ If the softene_ is installed where it could freeze (summer cabin, lake home, etc,), you must drain all water from it to stop possible freeze damage To drain the softener 1. Close water tank° 2. Open a faucet in the soft water pressure in the softener_ o , ,ll.
SECTION SOFTENER CARE OFYOUR 3D, HELPFUL HINTS CHECKLIST ,., TO HELP YOU SAVE MONEY If your water softener fails to work, make the following easy checks, Often, you wilt find what's wrong yourself and you won't have to call and wait for service. If you do not find anything wrong, -while making the checks, and your softener still does not work, call your Sears Service Department. NOTES: 1_Also read ERROR CODE, page 11. 2.
SECTION 4 OTHE. THINGS TOKNOW t_ i ! 4A. DIMENSIONS/SPECIFICATIONS BYPASS VALVES J SINGLE-PLASTIC _<'-_/il I I I SING_-BRASS .... / 2 OUTWAeD ! SE_CE >x'_ /_\ _.,,,,/ f l 1 Inward For Bypass _nward For tSERVICE A \\ ey_ _VALVE E D I t I 1 t Bypass Vatve C l I t I 1 SERVICE Close Bypass Vatve Open Inlet & Outlet Vatves x Inlet Valve BYPASS Open Bypass Valve Close _nlet & Outlet Valves % A B MODEL NO. 625.348571 .# . Salt Tank Height ....
SECTIO 5 SERVICE TECH. INFORMATION | i 5A. TROUBLESHOOTING Keep this manual with your water softener.. If repairs are needed, the service technician must have the information on the following 8 pages, For telephone assistance, call toll free, 1-800-426-9345 WIRING SCHEMATIC BACK OF TIMER (PWA) AClttPL_ O0 pos t IUKS#_Q c-_,__ _]on DO IH Motor, 24VAC © _rn Turbine Sensor _J bm o.,.
SECTION 5 SERVICE TECH INFORMATION I P ,,, ','', ,,,._, ii, 5A. AUTOMATIC n,i, i ....... ELECTRONIC DIAGNOSTICS While an error code appears in the display, all face plate buttons are inoperable except the SELECT button. SELECT remains operational so the service person can make the MANUAL INITIATED ELECTRONIC DIAGNOSTICS (below) to further isolate the defect, and check the water meter.
SECTION 5 SERVICE TECH. I.FORMAT O. 5A. VALVE POSITION the valve position, in the display: INDICATOR Serv .......... Fill ............. Brine ......... Bkwsh .......... Rinse ......... TROUBLESHOOTING INDICATORS: the following days this face plate has had electrical power applied. _.
SECTION 5 SERV,CE TECH ,NFORMAT,ON L I ,,,,,,, iii, .............. i,, i 5A. ,,,, ,,,,,,,,,;,;;, .............. MANUAL ADVANCE lUl TROUBLESHOOTING _ _ ,,,,, REGENERATION i .... CHECK NOTE: If water system pressure is low, an elevated drain hose may cause back pressure, stopping brine draw, This check verifies proper operation of the valve motor, brine tank fill, brine draw; regeneration flow iates, and other controller functions.
SEOTBON 5 SERV,CE TEC,.,NFORMAT, O, [ ,J 5B. ROTARY VALVE SERVICE tightening the screws, install the valve cam and gear_ Then, turn the rotor (clockwise only) to service position. Tighten the screws using a crisscross pattern. If a torque wrench is available, torque to 30-40 inch poundsr Before working on the valve, turn off the water supply and disconnect from electrical power. TO RELIEVE PRESSURE: --3 VALVE BYPASS: Close the inlet valve and open a soft water faucet.
SECTBON 5 SERVICE TECH INFORMATION t ] 50 . WATER FLOW THROUGH SERVICE THE SOFTENER VALVE CYCLE from Valve Inlet (hard water) distributor To Valve Outlet (soft water) resin tank POSITION Hard water enters the valve inlet port° Internal valve porting routes the water down and out the top distributor, into the resin tank. Hard water is softened as it passes through the resin bed, then enters the bottom distiibutor.
SECTION 5 SERVICE TECH.
$EGTIO 5 5C. SERVICE TECH INFORMATION WATER FLOW THROUGH THE SOFTENER VALVE FAST RINSE CYCLE soft water to valve outlet POSITION ! t \ \ During FAST RINSE, the rotor & disc is positioned so water flow enters the resin tap2< through the top distributor, and exits through the bottom distributor, to the drain ]-he electronic timer again energizes the motor to return the valve to service. As the valve rotates, the position switch lever drops to open the circuit.
SECTION 6 REPAIR PARTS KENMORE WATER SOFTENERS MODEL NOS. 625.348571 AND 625.348591 KEY I PART NO. I NUMBER Valve Assembly page 30) 1 2 7137612 Cover (main) Salt Hole Cover 3 7095373 Transformer, 24'7-10VA @.
SECTION 6 REPAIR PARTS ! t KENMORE WATER SOFTENERS MODEL NOS. 625.348571 AND 625.
SECTION 6 REPAIR PA.TS I ] KENMORE WATER SOFTENERS MODEL NOS° 625.
SECTION 8 REPAIR PARTS I ] KENMORE WATER SOFTENERS MODEL NOS. 625.348571 AND 625,348591 PARTS LIST KEY NO.
Deluxe Demand Water Softeners MODEL NOS. 625.348571 625.