Operator’s Manual 10-in. 2.2 Amp Electric ® Weedwacker Trimmer Model No. 172.740100 CAUTION: Read, understand and follow all Safety Rules and Operating Instructions in this Manual before using this product. Sears Brands Management Corporation, Hoffman Estates, IL 60179 See the full line of Craftsman® products at craftsman.
SAFETY SYMBOLS TABLE OF CONTENTS Warranty……………………………..................................……………..Page Safety Symbols……………………..................................……………..Page Safety Instructions……………………..................................……….....Pages Unpacking..……………………………..............................………….....Page Description………………………………..................................………..Pages Assembly and Adjustments………………………………......................Pages Operation...................………………………..................................
SAFETY INSTRUCTIONS cont. SAFETY INSTRUCTIONS PERSONAL SAFETY cont. handle and efficient tool; if used improperly or without the due precautions it could become a dangerous tool. For pleasant and safe work, ALWAYS strictly comply with the safety rules that are contained in this manual. ! WARNING: BE SURE to read and understand all instructions in this manual before using this electric trimmer.
SAFETY INSTRUCTIONS cont. SAFETY INSTRUCTIONS cont. EXTENSION CORDS cont. ELECTRICAL SAFETY cont. 2. Double insulation eliminates the need for the three-wire grounded power cord and grounded power supply system. Applicable only to Class II (double-insulated) tools. This trimmer is a double insulated tool. ! WARNING: GFCI (Ground Fault Circuit Interrupter) protection should be provided on all circuits or outlets to be used for electric lawn and garden power tools.
SAFETY INSTRUCTIONS cont. SAFETY INSTRUCTIONS cont. SAFETY RULES FOR ELECTRIC TRIMMERS cont. SAFETY RULES FOR ELECTRIC TRIMMERS cont. 6. USE RIGHT TRIMMER. Do not use trimmer for any job except that for which it is intended. ! 7. AVOID accidental starting. DO NOT carry a plugged in trimmer with your finger on the switch. 8. DO NOT carry the trimmer by the cord or pull the cord to disconnect it from the receptacle. Keep cord away from heat, oil and sharp edges. 9.
DESCRIPTION UNPACKING 1. The trimmer comes in 2 pcs. (Upper and Lower Shafts), that must be connected by hand. The Safety Guard must be attached. 2. Remove the Upper and Lower Shafts and Safety Guard from the carton and inspect your trimmer. 3. Do not discard box or packing material until all parts are examined. ! WARNING: If any part of the trimmer is missing or damaged, do not plug in the trimmer until the damaged part is repaired or replaced. KNOW YOUR TRIMMER (Fig.
DESCRIPTION cont. DESCRIPTION cont. This Trimmer has the following features cont.: SPECIFICATIONS 8. Cord Retention Hook helps keep the extension cord in place. 9. Safety Guard helps keep cuttings and debris away from operator. Safety “On” Button Fig. 3 Finger Trigger Switch Auxiliary Handle Cord Retention Hook Pigtail Power Cord Plug Upper Shaft Cutting Path 10 inches No-Load Speed 11,000 RPM Rating 2.2 Amp Line Diameter Nylon monofilament round single-wound 0.065-in.
ASSEMBLY & ADJUSTMENTS cont. INSTALLING THE SAFETY GUARD cont. (Figs. 5 and 5a ) 4. Attach the Safety Guard to the trimmer head making sure the sides are located into the grooves. 5. Insert the edge of the guard into the slot along the back of the trimmer’s head, carefullly lining the screw hole in the guard up with the screw hole in the trimmer head. 6. Insert screw and securely attach the safety guard (see Fig. 5). ! WARNING: To avoid injury, ALWAYS turn off and disconnect the trimmer OPERATION cont.
OPERATION cont. OPERATION cont. TRIMMING (Figs. 7) THE CUTTING LINE While trimming, move the trimmer from left to right, keeping it well away from the body. ! WARNING: DO NOT grasp the exposed cutting line when picking up or holding the trimmer. Fig. 7 Tilt the front of the trimmer head to cut shorter grass. DO NOT overload your trimmer. Overloading your trimmer can be avoided by making sure the motor speed does not drop too much while trimming. (See Fig. 7). Nylon monofilament round single-wound 0.
OPERATION cont. OPERATION cont. FILLING SPOOL WITH CUTTING LINE cont. (Fig. 10) 4. When the wound cutting line reaches the eyelets (recesses), cut the line. Temporarily park the line in the spool rail notch on one side of the spool as shown in Fig. 10. 5. Repeat the above procedure for the second cutting line on the lower section of the spool. 6. Fit the spool onto the tool as described in “REPLACE THE SPOOL” page 18. TO REPLACE CUTTING LINE (Fig.
ACCESSORIES MAINTENANCE ! WARNING: To avoid injury, ALWAYS turn off and disconnect the trimmer from the power outlet BEFORE installing line, cleaning the trimmer or making any adjustments. GENERAL MAINTENANCE Keep your trimmer clean and in good repair for maximum long-lasting performance. Before each use, inspect the switch and cord for damage. Check for damaged, missing, or worn parts.
The model number will be found on the nameplate of the Trimmer. To order parts, call 1-800-469-4663 Model No. 172.740100 10-in. 2.
