Operator's Manual I CRRFTSMRN°I evolv I 4.5 AMP JIGSAW Model No. 320.17434 0 us WARNING: To reduce the risk of injury, the user must read and understand the Operator's Manual before using this product. Sears, Roebuck www.craftsman.com and Co., Hoffman • • • • • • Estates, WARRANTY SAFETY ASSEMBLY DESCRIPTION OPERATION MAINTENANCE IL 60179 U.S.A.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
When in doubt, use the next heavier gauge. Always extension cords. A_, WARNING: Be sure to read and understand all instructions in this manual before using the reciprocating saw. Failure to follow all instructions may result in hazardous radiation exposure, electric shock, fire, and/or serious personal injury. Recommended sizes of extension cords Volts Ampere _, WARNING: Do not attempt to operate this tool until you have thoroughly read all instructions, safety rules, and warnings.
unstable and may lead to loss of control. SAFETY Do not force tool. Use the correct tool for your application. The correct tool will do the job better and more safely at the rate for which is designed. The label on your tool may include the following V ............................................................... Volts Do not use tool if the switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. A .....................................
• • • could cause your hand to move into the blade. Never reach into the cutting path of the blade. Blade guide rollers must support the blade when cutting. The rollers must rest against the back edge of blade. The only cutting operation when rollers do not support the blade is the scrolling mode. When scrolling the blade must swivel as it is guided to follow scroll patterns. Always move the base back and blade guide up and back away from blade in scrolling mode.
ID]=_.'_o_l[e_] [e]__ ON/OFF TRIGGER SWITCH KNOW YOUR JIGSAW (Fig. 1) Before attempting to use this jigsaw, familiarize features and safety requirements. yourself with all its operating _, WARNING: Do not allow familiarity with your saw to make you careless. Remember that a careless fraction of a second is sufficient enough to inflict severe injury. Fig. 1 Lock On Button On/Off Triger Variable Speed Dial 1. Plug your saw's 2. Start the tool by squeezing 3. Release the trigger to stop the tool.
the blade quickly and easily, without 1. Unplug the jigsaw 2. Place your finger on the lower edge of the seethrough blade guard, and pull it forward until it locks in place (Fig. 4). 3. Lift the tool-free the use of additional tools. orbital control that allows you to choose Simply Turn the lever to a lower setting to decrease There are three orbital action cutting different types of material. blade the tool-free blade change holder. (Fig.
3. Loosen the hex screw that Fig. 9 secures the base plate. Move the base plate slightly forward, and tilt it to the required angle (between 0° and 45 °) using the scale (0 °, 15 °, 30°and 45 °) that is marked on the base 5. Press down (to keep saw base plate against the workpiece) as you slowly push the saw in the direction of the cut. 6. Gradually build up the blade speed, cutting as close to the line as possible (unless you want to leave enough room for finish sanding). 7.
CUTTING ,_ WITH A STRAIGHTEDGE WARNING: (Fig. 12) To avoid A_, WARNING: accidents, always disconnect the tool from the power source before making any adjustments or attaching accessories. by a qualified _1, WARNING: To ensure safety and reliability, service technician tool from the power source before performing Always use a rough-cut blade whenever possible. Periodic maintenance operation. A cleaning 2. Mark the cutting line.
b/_l[l_I_ PROBLEM CAUSE Will not start when trigger [,,1][[I][I]llll]_] is squeezed Check to be sure power cord is connected to power source and that power source (outlet) is operable SOLUTION Jigsaw MODEL NUMBER Always mention the Model Number when ordering Connect to power source. Confirm power source (outlet) is operable Will not cut Check blade Replace if teeth are dull or worn Clean, clear vents. Motor overheating Be sure cooling vents are free from saw dust and obstacles \ \ 320.
1 2750122000 Rotor 1 2 3700214000 Washer 1 3 3550146000 Located 4 2821972000 Roller Support 5 3520061000 Sliding Block 2 6 3700229000 Pendulum 1 7 5610042000 Tapping Screw 9 8 3700149000 Square Washer 2 9 3320295000 Right Housing 10 3550177000 Guiding 11 3121725000 Transparent 12 3120473000 Lock Button 1 13 5610044000 Tapping 2 14 3520060000 Bushing 15 5610024000 Tapping 16 3650007000 Wire Guard 1 17 5700184000 Needle Bearing 1 18 3120234000 Co
17434Manual Revised 09-0727 Page 22 17434Manual Revised 09-0727 Page 23
Your Home For expert troubleshooting and home solutions advice: manage home www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it ! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME (1-800-469-4663) www.sears.