Operator's Manual CRI:IF X E MRN°I 12-Volt Lithium-Ion Cordless Multi-Tool Model No. 320.61199 c_ius LISTED • Warranty _k WARNING: To reduce the risk of injury, the user must read and understand the Operator's manual before using this product. • Safety • Assembly • Operation • Maintenance Charge battery Before first use Sears, Roebuck and Co., Hoffman Estates, IL 60179 www.craftsman.com U.S.A.
Warranty page 2 Safety Symbols page 3 Safety Instructions pages 4-12 Description page 13 Assembly pages 13-14 Operation pages 14-22 Application Page 23 Maintenance pages 24-25 Troubleshooting page 26 Exploded page 27 View and Part List Sears Repair Parts Phone Number Back Cover ONE YEAR FULL WARRANTY ON CRAFTSMAN® TOOL If this Craftsman tool fails to give complete satisfaction within one year from the date of purchase, return it to any Sears store or Parts & Repair Center or other C
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency W Watt Power rain Minutes "k., Alternating ---== Direct no Class ...
GENERAL SAFETY RULES _, WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. The term "power tool" in all of warnings listed below refers to corded power tools or battery-operated (cordless) power tools. READ AND SAVE THESE INSTRUCTIONS WORK AREA SAFETY • Keep your work area clean and well lit.
PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. Use safety equipment. Always wear eye protection. Safety equipment, as dust mask, non-skid safety shoes, hard hat, and hearing protection, used for appropriate conditions, will reduce personal injuries.
POWER TOOL USE AND CARE Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and more safely at the rate for which it was designated. Do not use the power tool if the switch does not turn it ON and OFF. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
BATTERY TOOL USE AND CARE • Make sure that the switch is in the OFF position before inserting the battery pack. Inserting the battery pack into power tools that have the switch ON invites accidents. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use power tools only with specifically designated battery other battery packs may create a risk of injury and fire. packs.
SERVICE • Have your power tool serviced • When servicing • Follow instructions by a qualified a power tool, use only identical in the Maintenance unauthorized parts or failure to follow risk of shock or injury. SPECIFIC SAFETY repair person. parts. section of this manual. Use of Maintenance RULES FOR CORDLESS to perform replacement instructions may create a MULTI-TOOL • Never use your Multi-Tool wet conditions. sanding or separating • Always wear eye protection.
• Only use application are torn or worn. accessories • Do not restart a cutting operation in the workpiece. To resume a cutting operation: while keeping the tool from contacting the workpiece, allow the tool reach full speed and then carefully guide the cutting accessory into the cut. • Keep your hands away from the cutting being cut. • Hold power tools by their insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.
• Keep the cord and charger from heat to prevent damage internal parts. • Do not allow gasoline, oils, petroleum-based products, etc. to come in contact with plastic parts. These materials contain chemicals that can damage, weaken, or destroy plastic. • An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and electric shock.
IM PORTANT SAFETY INSTRUCTIONS • Save these instructions. This manual contains instructions for 12V Multi-Tool 320.61199. • Before using the ,battery charger, read all instructions and cautionary markings on battery charger, the battery and the product using battery, well as the operator's manuals for these products. Fig.
ID]=_.'_o_[[o_] KNOW YOUR MULTI-TOOL (Fig.l) PRODUCT SEPCIFICATION Motor 12 Volt DC Tool Weight (with battery) 1.81bs Oscillation Rate 15000/Min Oscillation Angle _+1.
• If any part is damaged or missing, please refer to the numbers back page of operator's manual. listed on the PACKING LIST Multi-Tool, straight edge flush cut blade, circular saw blade, hardened steel scraping blade, carbide circular adhesive removal blade, carbide triangular rasp, sanding plate and 24 pcs sandpapers, hex key, vacuum adaptor, operator's manual.
BATTERY PROTECTION). BATTERY PROTECTION The battery circuitry protects the battery pack from extreme temperature, over discharge, and over-charge. To protect the battery from damage and prolong its life, the battery pack circuitry will turn off the battery pack if it becomes overloaded or if the temperature becomes too high during use. This may happen in situations involving extremely high torque, binding, and stalling.
HOW TO CHARGE THE BATTERY PACK NOTE: This Lithium-ion battery pack is shipped the first time, fully charge the battery pack. partially charged. A fully discharged battery pack will charge in about 30 minutes environment between 32 ° F (0 ° C) and 104 ° F (40 ° C). battery pack with the correct Before using it in an 1. Charge the Lithium-Ion charger. 2. Connect 3. Align the raised ribs of the battery pack with the slot in the charger. 4. Insert the battery pack into the charger 5.
CHARGING A HOT BATTERY PACK If the battery pack is above normal temperature range, the red LED will illuminate and the green LED will be off. When the battery pack cools down to approximately 104°F (40°C), the charger will automatically begin charging. CHARGING A COLD BATTERY PACK If the battery pack is below the normal temperature range, the red LED will illuminate and the green LED will be off. When the battery warms to a temperature of more than 32°F (0°C), the charger will automatically begin charging.
TO DETACH BATTERY PACK (Fig. 4) 1. Make sure that the tool is "OFF" 2. Depress the battery release buttons located on the both Fig. 4 sides of th of the battery pack to release the battery pack. 3. Pull the battery pack out and remove it from the tool. A_, CAUTION: When placing the battery pack in the tool, be sure that the raised rib on Fig. 5 battery pack aligns with the groove inside the tool and that the latches snap into place properly.
DETACHABLE VACUUM ADAPTOR (Fig.7) I Fig. 7 Always connect the vacuum adaptor when sanding. Remove the application tool before mounting the vacuum adaptor. To improve dust extraction from the working area, insert the dust-extraction adaptor into the rear of the tool, and connect the adaptor to a dust-extraction system or a suitable vacuum cleaner. ATTACHING THE APPLICATION A_, WARNING: TOOL (FIG.
Fig. 8 Fig. 9 Fig. 10 Ribs on shaft Grooves Fig. 11 0 30 120 60 150 MOUNTING/CHANGING A_, WARNING: 90 _ 180' 240' 300' 330' 210 THE SANDPAPER (Fig.12) Failure to remove the battery pack from the tool when assembling parts, making adjustments, or changing accidental starting causing possibly serious injury. 1. 270' Follow the directions for Attaching the Application Tool to attach the sanding plate to the Multi-Tool. 2.
SAWING Fig. 13 & WARNING: Use sharp, undamaged saw blades only. Deformed, blunt saw blades or saw blades that are otherwise damaged can break. WARNING: When sawing light building materials, observe the statutory provisions and the recommendations of the material _, suppliers. WARNING: Plunge cuts may only be applied to soft materials, such as wood, gypsum _, WARNING: plaster boards, etc. The sawing teeth are very sharp. Do not touch during mounting and application.
SANDING WARNING: very hot. Do not touch the gear box after prolonged use; it could be • The removal rate and the sanding pattern are determined sanding sheet and the work surface. by the choice of • Apply uniform sanding • Intensifying the sanding pressure does not lead to an increase of the sanding capacity, but instead it increases wear on the machine and the sanding sheet. • Use only the tip or an edge of the sanding sheet for precise sanding of edges, corners and hard to reach areas.
r:1-,J-,Jal[t]_aiil[,)_i ACCESSORY APPLI CATION Carbide Circular Adhesive Removal Blade Cut out the grout around tile Carbide Triangular Remove tile adhesive Hardened Steel Scraping Blade Rasp residue Remove floor coverings and scrape off adhesive residue Cut and remove the damaged part of plasterboard High Speed Steel Circular Saw Blade First make two parallel cuts, then break out the piece in between with chisel and sinker to lay the cable and plaster over High Carbide steel Straight Edge Flus
_, WARNING: To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance. _1, WARNING: When servicing, use only identical Craftsman Use of any other parts may create a hazard or cause product replacement parts. damage. A_, WARNING: It is not recommended to use compressed dry air as cleaning method of the tool.
(26°C) and free of moisture. • Store Lithium-Ion battery packs in a 30%-50% charged condition. • Every six months of storage, fully charge the Lithium-Ion battery • Exterior may be cleaned with a cloth or soft non-metallic brush. pack. BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING To preserve natural resources, please recycle or dispose of batteries properly. This product contains lithium-ion batteries.
PROBLEM CAUSE The tool does not work Battery Motor overheating Be sure cooling vents are free from dust and Clean, clear vents.
12 VOLT LITHIUM-ION CORDLESS MULTI-TOOL MODEL NUMBER 320.61199 The Model Number will be found on the Nameplate attached to the handle of the Multi-Tool. Always mention the Model Number when ordering parts for this tool.
61199 Manual_Revised_09 0310 Page 28
61199 Manual_Revised_09 0310 Page 29
Your Home For expert troubleshooting and home solutions advice: manage home www.managemyhome.