Deli Shop Model 436 Setup Guide SPECIFICATIONS ..................................................................................................................................1 INTERNAL PARTS LOCATION ..........................................................................................................2 INTERNAL PARTS LOCATION (CONTINUED) ..............................................................................3 INITIAL SET UP ......................................................................
Deli Shop Model 436 Setup Guide Notes . . .
Deli Shop Model 436 Setup Guide SPECIFICATIONS DIMENSIONS: WEIGHT: ELECTRICAL (U.S.): (INTERNATIONAL): REFRIGERATION: MISCELLANEOUS: Height - 183 cm (72 in.) Width - 73.6 cm (29 in.) Depth - 88.3 cm (34 3/4 in.) 266.3 kg (587 lbs.) 115 Volts AC, 60 Hertz, 12 Amps, Single Phase 230 Volts AC, 50 Hertz, 6 Amps, Single Phase Refrigerant - 134a Charge - 213 g (7.5 oz.
Deli Shop Model 436 Setup Guide INTERNAL PARTS LOCATION 2 4360001
Deli Shop Model 436 Setup Guide INTERNAL PARTS LOCATION (CONTINUED) 4360001 3
Deli Shop Model 436 Setup Guide INITIAL SET UP Unpack and Inspect 1. Carefully remove the merchandiser from its shipping carton and place it on a level surface. 2. Inspect the outside of the merchandiser for dents, scratches, or any damage resulting from improper handling. 3. If the merchandiser has the optional door lock, the key will be in the coin return receptacle. 4. Inspect the inside of the cabinet. Observe the location and position of the packing material should you need to reuse it.
Deli Shop Model 436 Setup Guide INSTALLATION NOTE This merchandiser is intended for INDOOR use only. CAUTION Make sure the merchandiser is properly leveled on a flat, solid, stable floor or base foundation. IF THIS IS NOT DONE, PERSONAL INJURY AND/OR DAMAGE TO EQUIPMENT MAY RESULT! 1. Move the merchandiser to the desired location. 2. Position the merchandiser at least 6 inches (15 cm) from any wall. 3. Using a spirit level, level the machine front to back and side to side.
Deli Shop Model 436 Setup Guide INSTALL THE COIN MECHANISM CAUTION Make sure the main power switch is turned OFF before you work on the merchandiser. Failure to do so could result in damage to electronic components. 1. Turn OFF the main power switch. Refer to the instructions provided with the coin mechanism and remove the coin validator assembly. 2. Loosen the coin mechanism mounting screws on the merchandiser so they stand off about 1/8" (0.3 cm). 3.
Deli Shop Model 436 Setup Guide INSTALL LABELS 4360001 7
Deli Shop Model 436 Setup Guide INSTALL THE DOOR LOCK There are two optional door locks: FLEX-ACE (P/N 9992000) a. Corresponding key b. (P/N 9994000) LOCK SPRING VAN LOCK (P/N 3112163) a. Coresponding key b. (P/N 3112164) c. Lock and key kit (P/N 3122165) SQUARE HOLE KEY Install the door lock as follows: LOCK CYLINDER 1. Remove the lock spring. 2. Depress the lock pin and push the lock cylinder in the lever until the pin snaps into place. LEVER 3. Test the lock mechanism with the key.
Deli Shop Model 436 Setup Guide LOAD THE MERCHANDISER 1. Adjust the product dividers, if necessary (page 23). 2. Set new prices, if desired. NOTE If the food carousel is loaded with items which are too large for the compartments, the carousel will not rotate properly. 3. Load any empty compartments. 4. Push in the load switch until the carousel rotates enough to expose more empty compartments. SWITCH 5. Repeat steps 3 and 4 until the carousel is fully loaded. VEND DOO 6. Close the door.
Deli Shop Model 436 Setup Guide PROGRAMMING Getting Around Getting around the Deli Shop software is pretty easy once you know the features that are available to you, and how to use them. The three main parts you will use are the SELECTION SWITCH PANEL, the DISPLAY, and the MODE switch. The Selection Switch Panel The selection switch panel is located on the monetary panel. These are the keys customers use to make selections, but you will use these keys during programming procedures.
Deli Shop Model 436 Setup Guide The Displays The display group consists of a 4-character digital display which performs two functions, and is referred to in this book as "the display": 1. It shows the customer's selection and how much credit is in the machine, as well as the standby message. ES USE EXACT CHANGE SELECTION PRICE 2. It provides information and feedback to the service person during maintenance.
Deli Shop Model 436 Setup Guide The display group also contains two lamps which light up under certain conditions: 1. The "USE EXACT CHANGE" lamp lights when there are insufficient coins in the merchandiser to provide change for a vend. You can set the criteria for this condition in the programming section. 2. The "SELECTION PRICE" lamp lights when the customer has inserted insufficient credit into the machine to vend the selected product.
Deli Shop Model 436 Setup Guide DATA View several types of sales data: NOTE All data is not resettable. 1. Press the MODE switch on the main controller. 2. Press until the display shows . The display will flash the total cash sales: . . . XXXX . . . XX.XX 3. If you have the DEX option, press to transfer data into your DEX device. 4. Press . The display shows - -, then flashes 4 to 8 digits. This is the dollar and cents amount of door 1 sales. 5. Press to view cash sales for doors 2 through 9. 6.
Deli Shop Model 436 Setup Guide PRICE Set prices for all the selections in your merchandiser: 4 5 9 The price display: 0 - -... changes to ... . Door number D C F Selection price 1. Press the MODE switch on the main controller. 427P0014 2. Press until the display shows . 3. Press , and the display shows - - , then .XX. "XX" is the price for door number 1. 4. Press until the selection you want to price is displayed. 5. Enter a new price with the number keys. 6.
Deli Shop Model 436 Setup Guide Faults Display all the active faults on your merchandiser: 1. Press the MODE switch on the main controller. 2. Press until the display shows 3. If errors are present, press . Note: If no faults are present, this will not be displayed. to see the list of faults: The EPROM is bad. RAM is not initialized or is not compatible with the currently loaded software.
Deli Shop Model 436 Setup Guide Configure Configure various machine functions: 1. Press the MODE switch on the main controller. 5 9 2. Press until the display shows 3. Press . The display shows the coin mechanism options: . 4 . = dumb mech 0 D C F . = MDB . = Exec mech . = No mech 427P0014 Press 4. Press . to switch between the coin mech choices. . The display shows the bill validator options: = Pulse validator (not supported at this time) . . . = MDB validator.
Deli Shop Model 436 Setup Guide 7. Press . The display shows: X.XX. The customer will see the USE EXACT CHANGE lamp lighted when the amount of available change in the coin mechanism falls below the level you set for X.XX. Enter a value with the number keys. For example, if . is selected, the customer sees the USE EXACT CHANGE lamp when less than a dollar’s worth of change is in the coin mechanism. 8. Press . The display shows either: . = More than one vend is allowed, with a declining balance.
Deli Shop Model 436 Setup Guide ROUTINE SERVICE AND SANITATION Sanitation is an important phase of merchandiser operation. The lack of proper cleaning and sanitation can cause merchandiser malfunction and loss of sales. The periods and suggested procedures for cleaning and sanitation are given as guides only, and are not to be construed as absolute or invariable. Local conditions must always be taken into consideration.
Deli Shop Model 436 Setup Guide General Set the main power switch OFF before cleaning or servicing the merchandiser. Use aerosol spray cleaners or spray waxes only in well-ventilated areas. NEVER use any spray product containing silicone. Silicone sprays can coat electrical contacts, causing a machine malfunction. WARNING Before using any liquid cleaner, unplug the merchandiser power cord or shut off power to the wall receptacle to avoid any possibility of electrical shock.
Deli Shop Model 436 Setup Guide Daily Sanitation 1. Remove all past-date merchandise from the merchandiser. 2. Check for liquid spillage on the merchandiser modules. If there is spillage, remove the module shelves and dividers affected. Wash and sanitize the shelves and dividers with a clean, damp disposable paper wiper or a clean soft-bristle brush. Rinse with clean hot water and dry thoroughly. 3. Wipe the exterior of the merchandiser with a damp disposable paper wiper and dry thoroughly. 4.
Deli Shop Model 436 Setup Guide Semi-annual Service 1. Follow the weekly service instructions. 2. Inspect the merchandiser for worn parts and replace where necessary. NOTICE Do not use silicone lubricants. Silicone can cause electrical contact failures. We recommend using Lubriplate Portable Tool Grease No. 905 (or equivalent), available from: Industrial Lubricating Company, Inc. P.O. Box 3871 St. Louis, MO 63122 3. Lubricate all moving parts that do not come into contact with food.
Deli Shop Model 436 Setup Guide Make copies of this record of cleaning form, cut it out, and keep it in a safe place. It will be your record of cleaning your merchandiser.
Deli Shop Model 436 Setup Guide ADJUSTING THE PRODUCT DIVIDERS Add or remove product dividers to accomodate various size products. Each tray segment can be left alone or divided into as many as 6 compartments, allowing the machine to vend up to 12 products per level. Proceed as follows: 1. Remove tray segment: a. Align the carousel as shown. b. Pull down on the spring clip to release the pin. c. Pull the tray segment directly out from the center. SPRING CLIP 427P0015 PIN RETAINER 2.
Deli Shop Model 436 Setup Guide ADJUSTING THE PRODUCT DIVIDERS (CONTINUED) 3. Install tray segment: a. Make sure the carousel is still aligned as shown. b. Carefully move the tray segment into position. Make sure the tabs on the ends of the tray segment line up with the tabs on the mating tray segment. c. Pull down the spring clip in order to allow the pin to seat into the hole in the spring clip. d. Push the tray segment the rest of the way home. e.
Deli Shop Model 436 Setup Guide TIMING THE CAROUSEL The tray dividers should be aligned with the adjacent edge on the vend door stop. If they are not aligned properly, follow the steps listed below: 1. Turn the main power switch OFF. 2. Remove the chain guard cover and the motor cover. 3. Verify that the motor is positioned so that the switch lever is bottomed out in one of the two cam detents. (This determines the motor’s stop position. You may have to release the brake and manually move the carousel.) 4.