Assembly Instruction

ManualsBrandsCrate & Barrel ManualsStorage FurnitureCrate & Barrel Abbott 52" Media Console

COMPONENTS

Made in China - r12 Page 1 of 6

Thank you for purchasing the Abbott Media Stand. This

page lists all the contents included in the box. Please

take time to identify the hardware as well as the individual

components of this product. As you unpack and prepare

for assembly, place the contents on a carpeted or

padded area to protect them from damage.

Note: 2 people are required to safely assemble this product.

ABBOTT MEDIA STAND

1 - middle

panel

2 - large drawer

front panels

1 - top panel

2 - small drawer

front panels

2 - side panels

(1 left, 1 right)

1 - back panel

2 - drawer

back panels

1 - bottom

panel

1 - top

partition

4 - drawer

side panels

1 - bottom

partition

1 - leg

2 - drawer

bottom panels

ASSEMBLY HARDWARE

TOOLS REQUIRED

Missing hardware?

Please call 800.606.6387 for

replacements.

18 - bolts 22 - wood

dowels

phillips head screwdriver

(We recommend the use of hand tools instead power tools)

6 - cam

screws

6 - cams

6 - cam

covers

56 - large

screws

WALL MOUNTING HARDWARE

1 - wall strap 1 - wall screw

12 - small

screws

Customer Service 800.967.6696 | Latest instructions available at www.crateandbarrel.com

Summary of content (6 pages)

PAGE 1
ABBOTT MEDIA STAND ASSEMBLY HARDWARE 12 - small screws 6 - cams 56 - large screws 18 - bolts 6 - cam covers 22 - wood dowels 6 - cam screws Missing hardware? Please call 800.606.6387 for replacements. WALL MOUNTING HARDWARE Thank you for purchasing the Abbott Media Stand. This page lists all the contents included in the box. Please take time to identify the hardware as well as the individual components of this product.
PAGE 2
ABBOTT MEDIA STAND NOTE: Do not over tighten the cam screws A A bottom partition left and right side panel B B top panel 1 A) Insert 4 wood dowels and 3 cam screws into left and right side panels as shown. Secure, but do not over tighten, cam screws using a phillips head screwdriver. B) Insert 8 wood dowels into top panel as shown. middle panel 2 A) Insert 4 wood dowels into bottom partition as shown. B) Insert 2 wood dowels into middle panel as shown.
PAGE 3
ABBOTT MEDIA STAND leg bottom panel 5 Fit dowels of bottom partition into corresponding holes of bottom panel. Secure with 4 large screws as shown. 6 Attach leg to bottom panel of assembly. Turn leg clockwise to secure. right side panel A NOTE: Make sure arrows on each cam point toward nearest edge with holes A B left side panel Made in China - r12 C 7 A. Fit dowels of left and right side panels into corresponding holes of assembled unit as shown and secure each side with 3 bolts. B.
PAGE 4
ABBOTT MEDIA STAND top panel back panel VIEW FROM BELOW NOTE: A short screwdriver is recommended to tighten small bolts during this assembly. Do not over tighten bolts. 8 With the assistance of another adult, carefully position unit upright. Fit dowels of top panel into corresponding holes of assembled unit. Secure top panel to assembled unit with 9 bolts as shown, using a screwdriver. 9 With the assistance of another adult, position unit face down as shown.
PAGE 5
ABBOTT MEDIA STAND large drawer front panel 12 Attach large drawer front panel to assembled unit with 4 large screws as shown. Repeat steps 11-13 for remaining drawer assembly. B 13 Fully extend drawer glides from assembled unit as shown. C CLEANING AND CARE Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the wood is finished with a protective clear lacquer.
PAGE 6
ABBOTT MEDIA STAND OPTIONAL SAFETY MOUNTING INSTRUCTIONS For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible. A. Insert wall screw (not included) through end of wall strap and into wall as shown. B. Insert wall screw (included) through end wall strap and into the top back of unit as shown.