SB9015F All-in-one Touch POS Terminal (i3 Processor) USER MANUAL
Table of Contents 1 Introduction ...................................................................................... 2 1.1 1.2 Safety Information ........................................................................................ 2 Electromagnetic compatibility statement ................................................. 3 2 Overview ............................................................................................ 4 2.1 2.2 2.3 2.4 Appearances .........................................
1 Introduction Thank you for purchasing the SB9015F(i3) all-in-one touch POS terminal, Bematech is committed to continuously improve product quality and provide better after-sales service. In order to take full advantage of our devices, we strongly recommend that you take the time to read this manual before diving into software solution. Note: Information in this manual may change without prior notice. 1.
Do not use harsh chemicals or strong cleaning solvents to clean the monitor screen. Wipe it clean with a soft terry cloth applied with a mild solution Do not share the same power outlet with high-power electrical appliances; keep distance from high level magnetic interference. Do not the use sharp pointed objects to work with the touch screen to avoid damage to the screen.
2 Overview 2.
2.
2.
2.4 Control Panel 1 Brightness – Press the “Brightness –” button to decrease brightness. The setting will be saved 6 seconds after releasing the button. 2 Brightness + Press the “Brightness +” button to increase brightness. The setting will be saved 6 seconds after releasing the button. 3 USB ports Connect external peripherals such as a memory drive. 4 Power Button Press to turn the POS terminal on or off. The LED lights up blue when the power is on.
3 Hardware Installation 3.1 Cable Routing 3.
3.3 Installing Customer Display 3.
3.5 Replacing System Core 3.
4 Setup and Driver Installation 4.1 Cash Drawer Port Pin-out 6 Pin 1 2 3 4 5 6 1 Description Sense input 2 Drive output 1 Sense input 1 +24V/+12V Drive output 2 Ground Note: The Y cable used to support two cash drawers on the single RJ-11 socket is same as that for Epson printers. Operation The Cash Drawer Controller use one I/O address to control the Cash Drawer.
4.2 Serial Ports Configurations Connectors COM1 COM2 COM3 COM4 COM5 COM6 Function External, RS232 External, RS232 Customer Display External, RS232 (RJ45) Touch controller External, RS232 Pin 9 Power Support RI/+5V/+12V select by jumper RI/+5V/+12V select by jumper +5V only RI/+5V/+12V select by jumper +5V only RI/+5V/+12V select by jumper COM4 RJ45 Socket Pin Assignment RJ45-10 Pin No. Signal Name 1 NC, or +5/+12 VDC 2 GND 3 DTR 4 CTS 5 TX 6 RTS 7 RX 8 DSR 9 DCD 10 NC 4.
JP6 - CN7 Cash Drawer Power Selection 1-2 +24V 2-3 +12V JP7 - CN1 USB Power Selection 1-2 +5VSB 2-3 Default=+5VSB +5V JP8 - CN4 USB Power Selection 1-2 +5VSB 2-3 Default=+24V Default=+5VSB +5V JP9 - COM4 RS232 pin 9 function select 1-2 RI 3-4 +5V 5-6 +12V Default=RI JP10 - COM6 RS232 pin 9 function select 1-2 RI 3-4 +5V 5-6 +12V Default=RI JP11 - COM2 RS232 pin 9 function select 1-2 RI 3-4 +5V 5-6 +12V Default=RI JP12 - COM1 RS232 pin 9 function select 1-2 RI 3-4 +5V 5-6 +12V Def
JP13 - PS/2 Keyboard Power Selection 1-2 +5VSB 2-3 +5V Default=+5VSB Note: Do not plug in or unplug any connector except USB devices when the power is on. The current loading for all COM ports should not exceed DC 5V/3A and DC 12V/2A.
4.4 Motherboard BIOS settings The POS terminal has a BIOS (Basic Input Output System) chip on the motherboard. Every time you start the terminals, the system will first run the BIOS self-test routine to check the main components of the system to ensure it is working properly. The terminal is loaded with default BIOS settings in the factory. change the parameters in the BIOS unless necessary.
Main Menu System Time and Date Setting: Under , select < System Date > or to change the system date and time.
AHCI Setting: Under < Advanced >, select .
Com and Parallel Port IRQ Setting: Under < Advanced >, select < F81866 Super IO Configuration >.
Security Tab Set the Supervisor or User password first to use the security features. Main Advanced Chipset Boot Security Save & Exit Password Description If ONLY the Administrator’s password is set, then this only limit access to Setup and is only asked for when entering Setup. → ←Select Screen If ONLY the User’s password is set, then this ↑↓ Select Item is a power on password and must be entered to Enter: Select boot or enter Setup.
4.5 Touch screen driver installation Step 1: Navigate to the installer directory to find the setup.exe file. Double-click on “setup.exe” to start installation. Step 2: When installation starts, click [Next] to proceed to the next step.
Step 4: Uncheck “Install PS/2 interface driver” and click [Next] to continue installation. Step 5: Uncheck “install RS232 interface driver” and click [Next] to continue installation.
Step 6: Select option “NONE”, click [Next] to continue installation.
Step 8: If there are additional touch monitors connected, please check “Support multi- monitor system”. Step 9: Select the destination location to install the touch driver. The default path is “C: \ Program Files \ eGalaxtouch”. Click [Next] to continue installation.
Step 10: Select the Program Folder to install the utility. “eGalaxtouch”. Click [Next] to continue installation. Step 11: Check the option to create a desktop shortcut icon.
After install the driver successfully, identify the USB controller is installed as shown below.
Touch calibration Touch device line test 26
27
5 Troubleshooting 1) Terminal does not boot If the terminal cannot boot after repeated pressing of the power switch when connect to the power, the terminal power light remains off, the fan does not operate, and the BIOS beeping is not heard, it might be power supply problems. (a) Check the power adapter is plugged in correctly to the power outlet. (b) Check the connection between the terminal and the power adapter, and then re-boot the machine.
(e) If the above steps do not resolve this problem, reinstall the operating system. 3) The touch screen does not respond (a) Remove the touch driver and then install it again. (b) Execute the “eGalaxTouch utility and check if the interface port is working. 4) When touching the screen, cursor always returns to a fixed position. (a) Check if there is anything pressing on the touch screen. (b) Other high power or high frequency equipment may affect the screen or controller.
8) The cursor in the touch screen can only move in a small area or touch positions are inaccurate. (a) This situation usually occurs first time after installing the driver. Please run the touch screen calibration program. We also recommend you to do this after changing monitor resolution. (b) Run the touch screen calibration program to do a 25-point recalibration.
6 Specifications MODEL Main Board CPU System Chipset Memory Storage Display LCD panel Resolution Brightness Touch Screen Tilting Angle I/O Ports External DC Input PS/2 Port Serial Ports SB9015F 15” i3 All-in-one Touch POS Terminal Intel i3-2310E Processor dual core 2.1GHz HM65 2 slots, DDR3 1066/1333, up to 4GB SATA 2.
SB9015F All-in-one Touch POS terminal 32