Owner`s manual

V100H Tube Guitar Amplifier with Reverb
6
The Rear Panel
22. AC Socket and Fuse: This is where
you connect the included power cord.
The grounded power cord should only
be plugged into a grounded power out-
let that meets all applicable electrical
codes. Make sure the Voltage Select
switch [23] is set for the correct voltage.
The fuse is located behind the fuse cover,
at the bottom of the AC socket. See the
“Service Information” section on page 14
for information about replacing the fuse.
Do not attempt to defeat the safety
ground connection.
23. Voltage Select Switch: Set this switch
to “115” for 100-120 VAC mains, and
to “230” for 220-240 VAC mains.
With the amplifier power cord
unplugged, use the tip of a small flat-
blade screwdriver to slide this switch to
the proper position.
24.
BOOST/REVERB FOOTSWITCH Jack:
Use this 1/4" TRS jack to connect
one of the footswitch cables to the
three-button footswitch (optional). This
allows for remote control switching of
the boost effect and the reverb (Tip =
boost on/off, Ring = reverb on/off).
Note: The footswitch overrides the
Boost In/Out switch [15] on the front
panel.
25. CHANNEL FOOTSWITCH Jack:
Use this 1/4" TS jack to connect one
of the footswitch cables to the three-
button footswitch (optional). This allows
for remote control of channel switching
(Clean/Overdrive).
Note: The footswitch overrides the
CHANNEL Select switch [7] on the front
panel.
26.
EFFECT SEND: Use this 1/4" TS jack to
send the signal to an external effects box.
Note: The Effect Send jack can be used
as a line-level output from the preamplifier
stage of the V100H to a mixer or recorder.
The signal comes after the EQ and Boost
stages but before the reverb stage.
27.
EFFECT RETURN: Use this 1/4" TS
jack to return the signal from an exter-
nal effects box.
Note: The Effect Return jack discon-
nects the signal from the preamplifier
stage of the V100H, so only the signal
at the Effect Return jack is sent on to
the power amplifier.
28. SPEAKER Outputs: Use these 1/4"
TS jacks to connect the amplifier to
one or more speaker cabinets, like the
Crate V412. Be sure the Impedance
switch [29] setting matches the total
impedance of all the speakers con-
nected to these two parallel jacks.
29. IMPEDANCE Switch: Set this switch to
the same impedance as the total load
of the speakers that are connected to
the Speaker Output jacks.
SPEAKER CABINET IMPEDANCE divided by
NUMBER OF CABINETS = TOTAL LOAD
1 x 16 ohm cabinet = 16 ohms
2 x 16 ohm cabinets = 8 ohms
2 x 8 ohm cabinets = 4 ohms
DO NOT USE A COMBINATION WITH A
TOTAL IMPEDANCE BELOW 4 OHMS!
c 2007 LOUD TECHNOLOGIES INC
DESIGNED IN ST.LOUIS MO, USA. MANUFACTURED IN CHINA, FABRIQUE EN CHINE
FOOTSWITCH
EFFECT
SEND
EFFECT
RETURN
SPEAKER
CHANNEL
BOOST/
REVERB
MINIMUM IMPEDANCE 4 OHMS
SPEAKER IMPEDANCE
4
8
16
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR
THE U.S. AND ICES-003, FOR CANADA. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
SERIAL NUMBER / MANF. DATE
AVI S: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
115
22 23
24 25 26 27 28 29