NanoLumens™ Flexible Display Setup and Operation Manual Rev B
NanoLumens Flexible Display Setup and Operation Manual NanoLumens™ Setup and Operation Manual DMAN-0001 REV B NanoLumens is a trademark of NanoLumens, Inc. Other companies‟ product names or trademarks are used herein for identification purposes only and belong to their respective companies. Copyright November 2010 NanoLumens, Inc. All rights reserved. 6225 The Corners Parkway, Suite 100 Norcross, GA 30092 678.421.9694 http://www.nanolumens.
NanoLumens Flexible Display Setup and Operation Manual Table of Contents 1.0 Introduction ........................................................................................................................ 1 1.1 FCC, UL, and CE Compliance ........................................................................... 1 2.0 Use of This Manual ............................................................................................................ 3 3.0 Overview of the Contents of This Manual ....
NanoLumens Flexible Display Setup and Operation Manual 6.5.2 Step 2: Connect the Display Controller to the Media Player ........................ 35 6.5.3 Step 3. Power Up and Test the System ......................................................... 36 7.0 Operational Checkout ....................................................................................................... 39 7.1.1 Visual Inspection ..........................................................................................
NanoLumens Flexible Display Setup and Operation Manual Figure 12. Load Points on a Hanging Bar (and Key) ....................................................... 21 Figure 13. Eye Bolt Load Points for a Ceiling Installation............................................... 22 Figure 14. Close-up of Eye Bolt Assembly ...................................................................... 22 Figure 15. Hanging Bracket Load Points for a Wall Installation ..................................... 23 Figure 16.
NanoLumens Flexible Display Setup and Operation Manual Revision History Revision vi Date Changes Made A September 15, 2010 Initial Release B November 16, 2010 Software configuration updates and Display Controller content.
Introduction 1.0 Introduction This is the Setup and Operations manual for the NanoLumens NL6 – 112" Flexible Display. The NanoLumens Flexible Display (hereafter called the “Flexible Display”) is a 112-inch diagonal screen that is less than two (2) inches thick, weighs less than 100 pounds, and is very energy efficient... running on standard 110VAC (universal input range). The extremely durable and robust screen is water resistant, sealed, and silent.
Use of This Manual 2.0 Use of This Manual This manual contains the information necessary to support Setup and Operation activities that are to be performed by qualified personnel installing and setting up the Flexible Display. Specific procedures can be located in the Table of Contents, which references a page number for each procedure contained in the manual. Conventions Used in This Manual When using this manual, you will note that some words and terms are in bold.
Contents of This Manual 3.0 Overview of the Contents of This Manual The following paragraphs describe the remaining sections of this manual. 4.0 Flexible Display Setup and Installation describes how to configure the Flexible Display hanging bar hardware. 5.0 System Setup Process provides an overview of the software system components and their setup. 6.0 Hardware Setup includes step-by-step procedures for connecting and setting up all components. 7.
Flexible Display Components 4.0 Flexible Display Setup and Installation 4.1 Flexible Display Components The following hardware, software and firmware components are provided by NanoLumens: Table 1.
NanoLumens Flexible Display Setup and Operation Manual Image Component Name Shipped with Shipping Crate Bushings Flat Washers Rolling Cart (2) (2) 1/4 - 20 (4) 3/8 - 16 (2) Cotter Pins (2) NanoLumens 48-60VDC Power Supply with one Power Supply A/C cable (1) Display Controller Unit with its own external power supply adapter (no image) 100‟ CAT5 data cable assembly (no image) 100‟ 10-gauge Shielded 48-60VDC power cable (no image) Spare Parts Kit (1):
Tool Requirements 4.1.1 Tool Requirements The following tools are not supplied by NanoLumens and are required to adjust the hanging bar‟s supplied hardware. You will need one of the tools checked in each column. Table 2.
Changing Out the Hanging Bars 4.2 Unloading and Loading Guidelines This section provides guidelines that should be taken into consideration whenever a Flexible Display is going to be unloaded from or loaded onto the shipping crate or the rolling cart. Upon delivery and prior to the start of any installation activities, a thorough inventory of equipment should be performed. Any missing hardware provided by NanoLumens should be addressed with NanoLumens immediately.
NanoLumens Flexible Display Setup and Operation Manual Cover the foam surface with clean blankets, and leave the soft, protective cover attached to the front of the display, for now. See Figure 1, below. Figure 1. Creating a Debris-Free, Level Work Surface 3. Extend the integral handle bars out on each side of the hanging bar. Figure 2. Extending the Handles Out Two people are required for steps 4 and 5. 4.
Changing Out the Hanging Bars Figure 3. Lifting the Flexible Display Up and Out of the Shipping Crate 5. Lay the display face-down, on top of the front door‟s debris-free foam surface. Figure 4. Display Face-Down on the Crate's Front Door Surface The display is now ready for configuration modifications as needed for its final mounting destination or for transference to the rolling cart.
NanoLumens Flexible Display Setup and Operation Manual Removing any unnecessary brackets or eye bolts (be sure to keep them in a safe place for later use.) NOTE: The Flexible Display software connection activity will be completed at the mounting location. The soft, protective cover may be detached once mounted. 4.2.2 Load into the Shipping Crate Use these steps after the Flexible Display has been taken down from its mounted location.
Changing Out the Hanging Bars 1/4-20 Long Bolt 1/4-20 Flat Washers Hanging Bracket (wraps around bar) Blue Bushings 3/8-16 Flat Washers Nylon Locking Nut Figure 6. Close-up of Hanging Bracket Assembly Front View 5. Extend the integral handle bars out on each side of the hanging bar. Two people are required for steps 6 through 9. Load the Flexible Display into the shipping crate: 6. Grasping the handle bars, carefully lift the Flexible Display up off the floor. You should be facing the display‟s face.
NanoLumens Flexible Display Setup and Operation Manual 8. Lift the display hanging bar with brackets up and over the shipping bar. 9. Pull the hanging bar downward to secure the brackets. They will fit snugly over the shipping bar. No additional bolts are needed to secure. Protect the Flexible Display’s face with the soft cover: 10. If not already attached, affix the Velcro edge of the soft, protective cover along the top of the hanging bar.
Changing Out the Hanging Bars 3. Grasping the handle bars, lift the display up and pull off of the cart. NOTE: Refer to the NanoLumens NL6 – 112” Flexible Display Specifications for weight specifications. 4. The Flexible Display is now ready for one of the following scenarios. Use the following table to determine your next steps. Table 3. Flexible Display Mounting Options If the Display… Then Do This… …is already prepped and ready for mounting… Take the display directly to its mounting destination.
NanoLumens Flexible Display Setup and Operation Manual 1. Carefully lay the display face-down, flat, on the provided cover and debris-free surface. WARNING! VERY IMPORTANT! Clear the foam, floor or table work surface of any debris. It is very important that the display face does not get scratched. 2. Using the recommended tools, remove any installed mounting hardware. 3. Add the eye bolts with appropriate hardware to the hanging bar in the position shown. Figure 8.
Changing Out the Hanging Bars Load the Flexible Display onto the cart: 5. With the Flexible Display facing you, grasp the handle bars and carefully lift the Flexible Display up off the floor, or out of its current position. NOTE: Refer to the NanoLumens NL6 – 112” Flexible Display Specifications for weight specifications. 6. Place the eye bolts over the cart‟s protruding long bolts (load points). 7. Secure using the cotter pins. Figure 10.
NanoLumens Flexible Display Setup and Operation Manual Figure 11. Remove the Integrated Handles' Screws 3. Remove the hanging brackets using a 7/16” open end or a 7/16” socket with ¼” ratchet driver. 4. Remove any eye bolts using a 7/16” open end or a pair of pliers. 5. With the handles, hanging brackets and eye bolts removed, slide the straight hanging bar out. 6. Slide the curved hanging bar in. NOTE: The correct orientation of the bar is to have the OPEN END DOWN.
Software Setup Process Overview 4.4 Installation Methods This section provides guidelines that should be taken into consideration whenever a Flexible Display will be installed or mounted for display. NOTE: Reusable load points.
NanoLumens Flexible Display Setup and Operation Manual 4.4.2 Load Points for Ceiling Installation Figure 13. Eye Bolt Load Points for a Ceiling Installation Eye Bolt 3/8-16 Flat Washer Hanging Bar (open end down, in between flat washers) 1/4-20 Flat Washer #1 Standard Rubber Grommet 1/4-20 Flat Washer #2 Nylon Locking Nut Figure 14.
Software Setup Process Overview 4.4.3 Load Points for Wall Installation Figure 15. Hanging Bracket Load Points for a Wall Installation 1/4-20 Long Bolt 1/4-20 Flat Washers Hanging Bracket (wraps around bar) Blue Bushings 3/8-16 Flat Washers Nylon Locking Nut Figure 16.
NanoLumens Flexible Display Setup and Operation Manual 5.0 System Setup Process 5.1 Overview The system is manufactured with the current firmware and software versions and default settings. Refer to Table 1 for a list of components shipped with the system. To install the hardware, follow the process outlined below. Each step below is described in further detail in section 6.5 System Setup Procedures.
Operational Checkout 6.0 Hardware Setup 6.1 Hardware Setup Guidelines This section provides guidelines that should be taken into consideration whenever a system is going to be set up. Every set of circumstances will be different, however, certain activities must be accomplished in every installation regardless of the details of the location or environment. These are: Upon delivery and prior to the start of any installation activities, a thorough inventory of equipment should be performed.
NanoLumens Flexible Display Setup and Operation Manual A/C Adapter 1. 112" Display NanoLumens Flexible Display 100 Feet Data Cable 2. Display Controller Unit Customer Media Player Optional Remote Power Supply ON/OFF 100 Feet Power Cable 3. AC-DC Power Supply 100-240VAC Figure 17: Overall System Configuration 6.3.
Operational Checkout Figure 19: NanoLumens Flexible Display Back View 6.3.2 NanoLumens Power Supply The NanoLumens 48-60VDC Power Supply is used to convert 110VAC power (US/domestic AC voltage) from a standard electrical outlet into 48-60VDC power to the Flexible Display.
NanoLumens Flexible Display Setup and Operation Manual On/Off Switch Figure 20: NanoLumens Power Supply Front View 30 DMAN-0001 REV B
Operational Checkout Fan Cable to Flexible Display Resettable Fuse Cable to Remote ON/OFF Control from Display Controller Unit Power Cable to 90-264VAC Outlet Figure 21: NanoLumens Power Supply Rear View DMAN-0001 REV B 31
NanoLumens Flexible Display Setup and Operation Manual 6.3.
Operational Checkout 6.4 Maintenance To maintain your system, NanoLumens recommends the following: Ensure that the Power Supply Unit air intake fan and area are free of dust. If the front of the Flexible Display becomes dusty or dirty, wipe it gently with a soft, dry cloth. 6.
NanoLumens Flexible Display Setup and Operation Manual 6.5.1 Step 1: Connect Power and Cables to the Flexible Display This step provides procedures to connect the cables from the Display Connector Unit and Power Supply to the Flexible Display. The data cable is the cable with the circular connector. Figure 25: Flexible Display Cable Connections 1. Connect the 48-60VDC power cable to the back of the Power Supply. 2. Using the AC power supply cable, connect the Power Supply to a 100-240V AC outlet.
Operational Checkout 6. On the front of the Power Supply, flip the black On/Off switch to the ON position. See Figure 20: NanoLumens Power Supply Front View. The Power Supply fan will start. 6.5.2 Step 2: Connect the Display Controller to the Media Player Next, provide power to the Display Controller Unit, and connect the Display Controller Unit to your Media Player. The following diagram is a depiction of the Basic Display Controller Unit Setup Configuration.
NanoLumens Flexible Display Setup and Operation Manual 2. Using the 18 Volt Power Supply, connect the Display Controller Unit into a 110240VAC power outlet. NOTE: The Display Controller has been calibrated to work specifically with the NanoLumens Flexible Display that has been shipped with. 6.5.3 Step 3. Power Up and Test the System 1. Press the Power button on the front of the Display Controller Unit to turn it on. The button should glow blue.
Operational Checkout Configuration Button Button Function Input Select Selects the Input Signal, allowing the manual selection of the Video Source. Cycles in the following order: VGA-Composite-SVideo-DVI- and then back to VGA. Reset Resets the Display Controller Unit. When this button is selected, the Unit cycles through the 4 Video Source types, above. If it does not find an input signal on a connector, it displays the message “No Input.
NanoLumens Flexible Display Setup and Operation Manual Rear of Box DB9/DB9 Male/Male Cable (Custom Length < 200feet) 3. AC-DC Power Supply 100-240VAC Green LED: Led ON = Power Supply is On Led OFF = Power Supply is OFF DB9 Port to Display Power Supply 2. Display Controller Box Toggle Switch Manual ON/OFF Figure 27: Power Supply Remote ON/OFF Configuration Front of Box USB NanoLumens Technical Support 2.
Operational Checkout 7.0 Operational Checkout The following procedure can be used to verify that the system has been installed properly and that it is operational following installation. This procedure is divided into two parts; first, is a visual inspection that can be performed prior to turning the system on; and second, is a step-by-step procedure that shall be performed to ensure the system is fully operational. Troubleshooting is embedded within the body of this procedure. 7.1.
NanoLumens Flexible Display Setup and Operation Manual 7.1.2 Flexible Display Monitor Status LEDs On the back of the Flexible Display, at the bottom of the unit, are two (2) rows of Light Emitting Diodes (LEDs). Figure 29: Flexible Display Status LEDs The LEDs function as follows: Table 6. Flexible Display Monitor Status LEDs LEDs Description 4 Red Solid LEDs Normal condition. 1 Orange Solid LED Normal condition. Flexible Display Unit is getting 4860VDC power.
Operational Checkout 7.1.4 Bending the Flexible Display The Flexible Display is designed to fit around curved surfaces, making it perfect for fitting around large pillars or other curved surfaces. The Flexible Display has a 48-inch bend radius. WARNING! Never try to fold the Flexible Display or bend it around anything smaller than 48 inches in radius, in any direction. 7.1.5 Flexible Display Environments The Flexible Display and all cables are sealed and water resistant.
NanoLumens Flexible Display Setup and Operation Manual 7.1.6 Checking System Operation Power up the PC. Power up the Power Supply. Check the following: o Flexible Display Status LEDs are lit. See Figure 29: Flexible Display Status LEDs. o The Video Processor Unit Status LEDs are lit (green is blinking; red is solid). o The resolution is set properly. o The image appears on the PC monitor. o The same image appears on the Flexible Display.
Technical Support 8.0 Technical Support The NanoLumens team is ready to help you. For technical support in the U.S., contact NanoLumens using the information below. Call NanoLumens at 678-421-9694, extension 111. Email NanoLumens at support@nanolumens.com.
Reference Information 9.0 Reference Information 9.1 NanoLumens NL6 – 112" Flexible Display Overview Product Name: NL6 - 112" Flexible Display Product Summary Thin Lightweight Flexible Energy Efficient System Components and Setup The NanoLumens Flexible Display solutions include the following components: 7. 112" Diagonal Flexible Display 8. Display Controller Box (With AC-DC Adapter) 9. AC-DC Power Supply A/C Adapter 1. 112" Display NanoLumens Flexible Display 100 Feet Data Cable 2.
NanoLumens Flexible Display Setup and Operation Manual 9.2 NanoLumens NL6 – 112" Flexible Display Specifications (Design and specifications subject to change without notice) DISPLAY DRAWINGS Front and Side Views Dimensions Table 7.
Specifications DISPLAY SPECIFICATIONS Table 8. Flexible Display Specifications Display Screen Size (Diagonal) 112" (2845 mm) Aspect Ratio 1:1.87 (Close to 16:9 or 1:1.
NanoLumens Flexible Display Setup and Operation Manual 9.
Specifications UNIT SPECIFICATIONS Table 9. Display Controller Specifications Inputs / Outputs Video Inputs: DVI-D (DVI + VGA), Composite, S-Video, Control Inputs: Main Power Switch, Display Management Output. RJ45 (Data) Remote Power Control Inputs Rocker Switch (Illuminated). Remote Power Control Outputs DB9 for Remote ON/OFF Control User Buttons Video Input Select, Reset, Diagnostics Main Power Input. 2.5mm Plug Threaded, Positive Center. Electrical Power Requirements, Input Specs.
NanoLumens Flexible Display Setup and Operation Manual 9.
Specifications UNIT SPECIFICATIONS Table 10. Main Power Supply Specifications Input / Output Power Requirements, Input Nema 5-15 to IEC320 C19, 6ft Cord. Power Requirements, Output IEC Connector for direct power line connection Control Input Remote ON/OFF Control (through Display Controller Unit) Electrical Power Requirements, Input Specs. AC 100 - 240V, 50Hz/60Hz, 20amp circuit Power Requirements, Output Specs. 48 to 60VDC, 30amp fused. Power Consumption 1500W Maximum.
NanoLumens Flexible Display Setup and Operation Manual 9.
Specifications Index C M Checkout, operational ......................... 39 Maintenance ........................................ 33 Contents of this manual ........................ 5 O E Operation............................................. 42 Environment ........................................ 41 Operational Description ...................... 28 Equipment Description and Purpose ... 27 P F Power Supply ...................................... 30 Flexible Display Diagrams .................
