Cut Sheet
Disposal
Dispose of contents/container in accordance with local/regional/national regulations.
Hazard(s) not otherwise
classified (HNOC)
None known.
Supplemental information
When exposed to extreme heat or hot surfaces, vapors may decompose to harmful or fatal corrosive gases such as hydrogen
fluoride, hydrogen chloride and possibly phosgene.
3. Composition/information on ingredients
Mixtures
CAS number
%
Chemical name
Common name and synonyms
156-60-5trans-1,2-dichloroethylene 80 - 90
HFC 43-10mee 138495-42-8decafluoropentane 10 - 20
Specific chemical identity and/or percentage of composition has been withheld as a trade secret.
4. First-aid measures
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Inhalation
Remove contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Get
medical advice/attention. Wash contaminated clothing before reuse.
Skin contact
Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
Eye contact
Call a physician or poison control center immediately. Do not induce vomiting. If vomiting occurs,
keep head low so that stomach content doesn't get into the lungs.
Ingestion
Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.
Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,
redness, swelling, and blurred vision. Skin irritation. May cause redness and pain.
Most important
symptoms/effects, acute and
delayed
Provide general supportive measures and treat symptomatically. Keep victim warm. Keep victim
under observation. Symptoms may be delayed.
Indication of immediate
medical attention and special
treatment needed
Ensure that medical personnel are aware of the material(s) involved, and take precautions to
protect themselves. Show this safety data sheet to the doctor in attendance.
General information
5. Fire-fighting measures
Foam. Powder. Carbon dioxide (CO2).
Suitable extinguishing media
Do not use water jet as an extinguisher, as this will spread the fire.
Unsuitable extinguishing
media
When exposed to extreme heat or hot surfaces, vapors may decompose to harmful or fatal
corrosive gases such as hydrogen fluoride, hydrogen chloride and possibly phosgene.
Specific hazards arising from
the chemical
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Special protective equipment
and precautions for firefighters
Fire-fighting
equipment/instructions
Move containers from fire area if you can do so without risk.
No unusual fire or explosion hazards noted.
General fire hazards
6. Accidental release measures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear
appropriate protective equipment and clothing during clean-up. Avoid breathing mist or vapor. Do
not touch damaged containers or spilled material unless wearing appropriate protective clothing.
Ensure adequate ventilation. Local authorities should be advised if significant spillages cannot be
contained. For personal protection, see section 8 of the SDS.
Personal precautions,
protective equipment and
emergency procedures
Use water spray to reduce vapors or divert vapor cloud drift. This product is miscible in water.
Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is
possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product
recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.
Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.
Methods and materials for
containment and cleaning up
2 / 8
Material name: T-Force® Degreaser
No. 03118 (Item# 1003394) Version #: 02 Revision date: 10-11-2017 Issue date: 10-11-2017
SDS US