MSDS

ManualsBrandsCRC ManualsChemicals & Cleaning Supplies12 WT OZ SILICONE MOLD RELEASE MOLD RELEASE LUBRICANT

SAFETY DATA SHEET

1. Identification

Silicone Mold ReleaseProduct identifier

Other means of identification

03300

Product code

Mold release

Recommended use

None known.

Recommended restrictions

Manufacturer/Importer/Supplier/Distributor information

Company name

CRC Industries, Inc.

Address

885 Louis Dr.

Warminster, PA 18974 US

Telephone

General Information

215-674-4300

Technical

Assistance

800-521-3168

Customer Service

800-272-4620

24-Hour Emergency

800-424-9300 (US)

(CHEMTREC)

703-527-3887 (International)

Website

www.crcindustries.com

2. Hazard(s) identification

Category 2Flammable aerosols

Physical hazards

Liquefied gasGases under pressure

Category 2Skin corrosion/irritation

Health hazards

Category 2Serious eye damage/eye irritation

Category 2Carcinogenicity

Category 1BReproductive toxicity

Category 3 respiratory tract irritationSpecific target organ toxicity, single exposure

Category 3 narcotic effectsSpecific target organ toxicity, single exposure

Category 2 (kidney, liver, nervous system)Specific target organ toxicity, repeated

exposure

Category 3Hazardous to the aquatic environment, acute

hazard

Environmental hazards

Category 3Hazardous to the aquatic environment,

long-term hazard

Not classified.

OSHA defined hazards

Label elements

Signal word

Danger

Hazard statement

Flammable aerosol. Contains gas under pressure; may explode if heated. Causes skin irritation.

Causes serious eye irritation. May cause respiratory irritation. May cause drowsiness or dizziness.

Suspected of causing cancer. May damage fertility or the unborn child. May cause damage to

organs (kidney, liver, nervous system) through prolonged or repeated exposure. Harmful to

aquatic life. Harmful to aquatic life with long lasting effects.

1 / 9

Material name: Silicone Mold Release

03300 Version #: 04 Revision date: 12-27-2016 Issue date: 02-10-2015

SDS US

Summary of content (9 pages)

PAGE 1
SAFETY DATA SHEET 1. Identification Product identifier Silicone Mold Release Other means of identification Product code 03300 Recommended use Mold release Recommended restrictions None known. Manufacturer/Importer/Supplier/Distributor information Company name Address Telephone General Information Technical Assistance Customer Service 24-Hour Emergency (CHEMTREC) Website CRC Industries, Inc. 885 Louis Dr.
PAGE 2
Precautionary statement Prevention Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Use with adequate ventilation. Open doors and windows or use other means to ensure a fresh air supply during use and while product is drying.
PAGE 3
Fire-fighting equipment/instructions In case of fire: Stop leak if safe to do so. Move containers from fire area if you can do so without risk. Containers should be cooled with water to prevent vapor pressure build up. General fire hazards Flammable aerosol. Contents under pressure. Pressurized container may rupture when exposed to heat or flame. 6.
PAGE 4
Appropriate engineering controls Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.
PAGE 5
Hazardous decomposition products Hydrogen bromide. Carbon oxides. 11. Toxicological information Information on likely routes of exposure May cause damage to organs through prolonged or repeated exposure by inhalation. May cause Inhalation drowsiness and dizziness. Headache. Nausea, vomiting. May cause irritation to the respiratory system. Skin contact Causes skin irritation. Eye contact Causes serious eye irritation.
PAGE 6
Specific target organ toxicity single exposure May cause respiratory irritation. May cause drowsiness and dizziness. Specific target organ toxicity repeated exposure May cause damage to organs (kidney, liver, nervous system) through prolonged or repeated exposure. Aspiration hazard Not an aspiration hazard. Chronic effects May cause damage to organs through prolonged or repeated exposure. Prolonged inhalation may be harmful. Prolonged exposure may cause chronic effects. 12.
PAGE 7
IATA UN number UN proper shipping name Transport hazard class(es) Class Subsidiary risk Packing group ERG Code Special precautions for user Other information Passenger and cargo aircraft Cargo aircraft only IMDG UN number UN proper shipping name Transport hazard class(es) Class Subsidiary risk Packing group Environmental hazards Marine pollutant EmS Special precautions for user UN1950 Aerosols, flammable, Limited Quantity 2.1 Not applicable.
PAGE 8
SARA 302 Extremely hazardous substance No US state regulations US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd. (a)) n-propyl bromide (CAS 106-94-5) US. New Jersey Worker and Community Right-to-Know Act dimethyl ether (CAS 115-10-6) n-propyl bromide (CAS 106-94-5) US. Massachusetts RTK - Substance List dimethyl ether (CAS 115-10-6) n-propyl bromide (CAS 106-94-5) US.
PAGE 9
Prepared by Allison Cho Version # 04 Not available. Further information HMIS® ratings NFPA ratings Health: 2* Flammability: 2 Physical hazard: 0 Personal protection: B Health: 2 Flammability: 2 Instability: 0 NFPA ratings 2 2 Disclaimer Revision Information 0 The information contained in this document applies to this specific material as supplied. It may not be valid for this material if it is used in combination with any other materials.